TEAC IF-AV/DM IF-AV:DM Owner's Manual - Page 1

IF-AV/DM Aviom Pro16 A-Net Interface Card Introduction Thank you for purchasing the TASCAM IF-AV/DM Aviom Pro16 A-Net Interface Card. This card allows your TASCAM Digital Mixer to feed monitor audio to any number of Aviom Pro16 A-Net devices such as the A-16II Personal Mixer. Before using the unit, please take time to read this manual thoroughly to ensure you understand how to properly set up and connect the unit, as well as the operation of its many useful and convenient functions. After you have finished reading this manual, please keep it in a safe place for future reference. You can also download the Owner's Manual from the TASCAM web site (http://www.tascam.com). Features •• Transmission of up to 16 channels of audio. •• Compatible with 24 bit quantization and 44.1 kHz and 48 kHz sampling frequency •• Convenient on-screen stereo link control. Trademarks •• TASCAM is a trademark of TEAC Corporation, registered in the U.S. and other countries. •• Aviom, A-Net, and Pro16 are trademarks of Aviom, Inc. •• Other company names, product names and logos in this document are the trademarks or registered trademarks of their respective owners. Product components The included items are listed below. Take care when opening the package not to damage the items. Keep the package materials for transportation in the future. Please contact the store where you purchased this unit if any of these items are missing or have been damaged during transportation. •• Main unit 1 •• Attachment screws 5 •• Owner's Manual (this document 1 Names and functions of parts 1 RJ-45 Connector for A-Net D01106120A DM-3200/DM-4800 requirements In order to use the IF-AV/DM card, the DM-4800/DM-3200 must use software version 1.70 or later. The mixer cannot recognize the IF-AV/DM card when using earlier versions. Check the TASCAM website (http://www.tascam.com/) for the latest DM-4800/DM-3200 software and download the TFI update file. Install TMCompanion, which is included on the CD-ROM included with the DM-4800/DM-3200, on the computer that you are using. Launch TMCompanion and use the TFI update file to upgrade the software version used by the DM-4800/DM-3200. Installation NOTE • DM-3200: Install the IF-AV/DM in mixer slot 1. It will not function in slot 2. • DM-4800: Install the IF-AV/DM in mixer slot 1 or 3. It will not function in slot 2 or 4. • Turn the mixer power OFF before beginning installation. 1 Remove the five screws from the cover panel of the slot where you want to install the IF-AV/DM card (slot 1 on a DM-3200, slot 1 or 3 on a DM-4800), and then remove the panel. (If that slot already contains a card, remove the card.) 2 Insert the IF-AV/DM card into the slot. Insert the card completely, aligning its edges with the white guidelines on the inside of the slot. Push the card in until it clicks into place and its backplate is even with the back of the mixer. Do not, however, push the card too hard. If you are having difficulty inserting it properly, pull it out once and try again. 3 Use the five screws that you removed earlier or the five screws included with this card to fix the card in place. 4 Turn the mixer's power ON, and open the DIGITAL screen (with the ALT key indicator lit, press screen mode selection key 2). Select the SLOT tab (SLOT 1-2 or SLOT 3-4 for the DM-4800), and confirm that the unit recognizes the installed card. If a "No Card" message appears, the card might not have been inserted properly or the screws might not be tight enough. Compatibility The IF-AV/DM interface card, when installed and properly configured, is compatible with the following Aviom Pro16 Series products: •• A-16II Personal Mixer (the original A-16 is not supported) •• A-16R rack-mounted Personal Mixer •• AN-16/o Output Module