TEAC W-890RmkII-B Manual for W-890R - Page 13

Continuous playback, RTZ I (TAPE I only), A-B Repeat playback

Get TEAC W-890RmkII-B PDF manuals and user guides View all TEAC W-890RmkII-B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

ENGLISH Continuous playback RTZ I (TAPE I only)  Continuous playback can be performed between TAPE I and TAPE II. When one tape is played back to the end, the other tape automatically starts playback, in a relay fashion. 1 Load pre-recorded tapes into the TAPE I and TAPE II compartments. 2 Set the DOLBY NR switch. Always set the DOLBY NR switch to the same position that was used for recording. When you press the RTZI key, the TAPE I deck fast-forwards or rewinds the tape until the counter reads , and then stops. NOTE < RTZ (Return-to-zero) only works on TAPEI. < If the counter position is too close to the 0000 mark (greater than 9994 or less than 0005), the RTZ function cannot be used. A-B Repeat playback 3 Set the REV MODE switch to the p(CONT PLAY) position. 4 Press the PLAY (h or y) key of the deck you want to start first. 1. During playback, press the REPEAT key at the point where you want to start the repeat playback interval (A point). 4' appears on the display when this point is set. You can start continuous playback from either TAPE I or TAPE II. Playback cycles through four tape sides as follows, and will continue as many as 5 times when you start the playback from Side "A" on TAPE I, or until you stop the operation. TAPE I Side"A" w Side "B" 2 x TAPE II Side "B" s Side "A" 2. Next, press the REPEAT key at the point where you want to end the repeat playback interval (B point). 4'appears on the display. The tape automatically rewinds to the A point where playback restarts. When the B point is reached, playback stops temporarily, the tape rewinds again to the A point, and playback continues to repeat. 3. Press the STOP (H) key to end repeat playback. CAUTION < During repeat playback, only the REPEAT and STOP keys can be used. < This function cannot be used for durations of less than 10 counts on the tape counter between the starting and end points. < Only intervals in the current playback direction can be repeated. < Repeat playback stops automatically after 20 repetitions. 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
13
ENGLISH
Continuous playback
±
Continuous playback can be performed between TAPE
I
and TAPE
II
.
When one tape is played back to the end, the other tape automatically
starts playback, in a relay fashion.
1
Load pre-recorded tapes into the TAPE
I
and TAPE
II
compartments.
2
Set the DOLBY NR switch.
Always set the DOLBY NR switch to the same position that
was used for recording.
3
Set the REV MODE switch to the
p
(CONT PLAY) position.
4
Press the PLAY (
h
or
y
) key of the deck you want to start
first.
You can start continuous playback from either TAPE
I
or TAPE
II
.
Playback cycles through four tape sides as follows, and will
continue as many as 5 times when you start the playback from
Side “A” on TAPE
I
, or until you stop the operation.
TAPE
I
Side“A”
w
Side “B”
2
x
TAPE
II
Side “B”
s
Side “A”
RTZ
I
(TAPE
I
only)
When you press the RTZ
I
key, the TAPE
I
deck fast-forwards or rewinds
the tape until the counter reads
, and then stops.
NOTE
<
RTZ (Return-to-zero) only works on TAPE
I
.
<
If the counter position is too close to the 0000 mark (greater than
9994 or less than 0005), the RTZ function cannot be used.
A-B Repeat playback
1. During playback, press the REPEAT key at the point where
you want to start the repeat playback interval (A point).
appears on the display when this point is set.
2. Next, press the REPEAT key at the point where you want to
end the repeat playback interval (B point).
appears
on the display.
The tape automatically rewinds to the A point where
playback restarts. When the B point is reached, playback
stops temporarily, the tape rewinds again to the A point,
and playback continues to repeat.
3. Press the STOP (
H
) key to end repeat playback.
CAUTION
<
During repeat playback, only the
REPEAT
and
STOP
keys can be
used.
<
This function cannot be used for durations of less than 10 counts
on the tape counter between the starting and end points.
<
Only intervals in the current playback direction can be repeated.
<
Repeat playback stops automatically after 20 repetitions.