TP-Link 13dBi CPE510 V1 QIG

TP-Link 13dBi Manual

Get TP-Link 13dBi PDF manuals and user guides View all TP-Link 13dBi manuals
Add to My Manuals
Save this manual to your list of manuals

TP-Link 13dBi manual content summary:

  • TP-Link 13dBi | CPE510 V1 QIG - Page 1
    Installation Guide Outdoor CPE CPE210 / CPE220 / CPE510 / CPE520
  • TP-Link 13dBi | CPE510 V1 QIG - Page 2
  • TP-Link 13dBi | CPE510 V1 QIG - Page 3
    Site Consideration 3 Connection and Installation 5 Lightning & ESD Protection 6 Software Configuration Logging into the PharOS 8 Configuration for Typical Applications 11 • Point-to-Point 11 • Point-to-Multipoint 13 • Hotspot 15 Antenna Alignment 17 Specifications 18 FAQ
  • TP-Link 13dBi | CPE510 V1 QIG - Page 4
    products including CPE210, CPE220, CPE510 and CPE520. • Package Contents Power Cord Pharos CPE Passive PoE Adapter • LED Explanation Pole Mounting Straps Installation Guide LAN1 LAN0 POWER AP/AP Router mode: All four LEDS remain solid. Client/Bridge/Repeater/AP Client Router mode: That the
  • TP-Link 13dBi | CPE510 V1 QIG - Page 5
    • Panel Layout Pharos CPE: Grounding Shielded Ethernet Port Shielded Ethernet Port Terminal LAN0 (Passive PoE in) LAN1 RESET Passive PoE Adapter: Power LED The Power LED indicates the status of the electric current: green (0~0.8A), red (0.8A~1A). 2
  • TP-Link 13dBi | CPE510 V1 QIG - Page 6
    Hardware Connection 1. Site Consideration • Mounting Height Ensure a clear line of sight between the wireless devices for an optimum performance. An elevated location is recommended as obstacles like trees, buildings and large steel structures will weaken the wireless signal. See 'Q2' in 'FAQ' for
  • TP-Link 13dBi | CPE510 V1 QIG - Page 7
    • Orientation Install the CPE devices with the front facing the intended signal receiving devices. You can orient the devices with the assistance of Google Maps, GPS and some landmarks according to the horizontal beamwidth listed below. Models Horizontal Beamwidth CPE210 70° CPE220 45° CPE510 45
  • TP-Link 13dBi | CPE510 V1 QIG - Page 8
    2. Connection and Installation Please connect and install the device as shown in the figure below. 5734 cause undesired operation. IP: 192.168.0.254 Username: admin Password: admin Power: 24V 1A 5GHz 300Mbps 13dBi Outdoor CPE Default Settings: Model: CPE510 LAN0 POE LAN Ethernet cable
  • TP-Link 13dBi | CPE510 V1 QIG - Page 9
    connection, then it is necessary to connect the grounding terminal of the CPE to earth ground through grounding cable (method 2 ). Two Methods: 1 Cable CPE Grounding Terminal Grounding Cable Grounded 3-wire Power Outlet 1 1 Shielded CAT5e (or above) Cable with Ground Wire 1 2 PoE Adapter
  • TP-Link 13dBi | CPE510 V1 QIG - Page 10
    Sheath Twisted Pair Ground Wire Cable Shield Secondary Cable Shield Shielded RJ45 Connector Shielded CAT5e (or above) Cable with Ground Wire 7
  • TP-Link 13dBi | CPE510 V1 QIG - Page 11
    introduces the login to the PharOS Web Interface and the software configurations to implement three typical applications, including point-to-point, point-to-multipoint and hotspot. 1. Logging into the PharOS 1. Before accessing the PharOS Web Interface, you need to assign a static IP address 192
  • TP-Link 13dBi | CPE510 V1 QIG - Page 12
    and press 'Enter'. It is recommended to use the latest version of Google Chrome, Safari or Firefox. 3. The 'Login' page will appear, set the parameters as below. • Username: admin. • Password: admin. • Region: select according to your country/region. • Select 'I agree to these terms of use'. • Click
  • TP-Link 13dBi | CPE510 V1 QIG - Page 13
    5. Then you will log in to the PharOS Web Interface and see the Status page as shown in the figure below. 10
  • TP-Link 13dBi | CPE510 V1 QIG - Page 14
    . Computer Access Point LAN: 192.168.0.254 Client LAN: 192.168.0.2 IP camera Refer to the following steps to configure the CPEs. Configure the Access Point 1. Log in to PharOS 2. Go to the Quick Setup page 3. Operation Mode • Select 'Access Point'. • Click 'Next'. 4. LAN Settings: Click
  • TP-Link 13dBi | CPE510 V1 QIG - Page 15
    Configure the Client 1. Log in to PharOS 2. Go to the Quick Setup page 3. Operation Mode • Select 'Client'. • Click 'Next'. 4. LAN Settings • IP Address: 192.168.0.2 (in the same subnet with the Access Point) • Click 'Next'. 5. Wireless Client Settings • SSID of Remote AP: click 'Survey', select the
  • TP-Link 13dBi | CPE510 V1 QIG - Page 16
    CPE of the subscribers, please contact the ISP for related information, as the configuration may vary due to different ISPs. Configure the Access Point (a typical configuration for Internet Service Provider): 1. Log in to PharOS 2. Go to the Quick Setup page 3. Operation Mode • Select 'Access Point
  • TP-Link 13dBi | CPE510 V1 QIG - Page 17
    password of the Access Point. • Distance Setting: enter the distance between the client and the remote Access Point to be connected. It is recommended to round the number up to the nearest integer. 6. Wireless AP Settings: Click 'Next'. 7. Finsh: Click 'Finish'. After finishing the CPE configuration
  • TP-Link 13dBi | CPE510 V1 QIG - Page 18
    CPE. Configure the Access Point 1. Log in to PharOS 2. Go to the Quick Setup page 3. Operation Mode • Select 'Access Point'. • Click 'Next'. 4. LAN Settings: Click 'Next'. 5. WAN AP Settings • SSID: customize the name for the network as you like. • Security: select 'WPA-PSK/WPA2-PSK'. • PSK Password
  • TP-Link 13dBi | CPE510 V1 QIG - Page 19
    Laptop Tablet Refer to the following steps to configure the CPE. Configure the AP Router (equal to a SOHO router) 1. Log in to PharOS 2. Go to the Quick Setup page 3. Operation Mode • Select 'AP Router'. • Click 'Next'. 4. WAN Connection Type *These settings may vary depending on the ISP. Please
  • TP-Link 13dBi | CPE510 V1 QIG - Page 20
    Antenna Alignment In order to get the best performance, you can precisely align the direction of the CPE with the assistance of 'Wireless Signal Quality' on 'STATUS' page of the PharOS Web Interface. Adjust the direction of the CPE until the device reaches the highest SNR. WISP WISP 17
  • TP-Link 13dBi | CPE510 V1 QIG - Page 21
    CPE520/CPE220: 275.83*79*60.3mm CPE510/CPE210: 224.34*79*60.3mm LAN0: 10/100Mbps Ethernet Port(PoE IN) LAN1: 10/100Mbps Ethernet Port GND: Grounding Terminal for Lightning Protection RESET: Button to restore the device to Factory Default 24V Passive PoE Adapter Included 15kV Up to 6kV -30℃ ~ 70
  • TP-Link 13dBi | CPE510 V1 QIG - Page 22
    FAQ (Frequently Asked Questions) Q1. How to restore the CPE to its factory default settings? With the CPE powered on, press and hold the 'RESET' button of the CPE or the 'Remote Reset' button of the passive PoE adapter for about 8 seconds until the Wireless Signal Strength LEDs flash. Method 1:
  • TP-Link 13dBi | CPE510 V1 QIG - Page 23
    signal strength of the devices, installers need to minimize the effect H h+r*(1 40%) (H is the height of the CPE) d1 r h = the height of obstacle at this point r = d1 × d2 ⋅ c d1 + the distances between the point and the devices in meters For example, assume d1 is 2km, d2 is 8km, and f is 2.4GHz,
  • TP-Link 13dBi | CPE510 V1 QIG - Page 24
    Click the button. 2. The following window will pop up. Click 'Yes' and you will then get into the 'Spectrum Analysis' page. 3. Select the 'Frequency Range' and click the 'Start' button, the PharOS will begin to analyze the power of the frequency. Watch the curves for a period of time, and then
  • TP-Link 13dBi | CPE510 V1 QIG - Page 25
    frequency is within the noted frequency range. So, in this example, the recommended Channel/Frequency is 116/5580MHz. Q4. What is Pharos MAXtream? Pharos MAXtream is a proprietary protocol developed on the basis of Time Division Multiple Access (TDMA) by TP-LINK. The MAXtream technology has the
  • TP-Link 13dBi | CPE510 V1 QIG - Page 26
    STATEMENT This equipment has been tested and found to comply with radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio warranty. If you need service, please contact us. • Avoid water and wet locations.
  • TP-Link 13dBi | CPE510 V1 QIG - Page 27
    NCC Notice & BSMI Notice 注意！ 於 5.25GHz 至 5.35GHz 5.250~5.350GHz This product can be used in the following countries: AT / BG / BY / CA / CZ / DE / DK / EE / ES / FI / FR / GB / GR / HU / IE / IT LT / LV / MT / NL / NO / PL / PT / RO / RU / SE / SK / TR / UA / US
  • TP-Link 13dBi | CPE510 V1 QIG - Page 28
    to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2014 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. Website: http://www.tp-link.com Tel: +86 755 26504400 E-mail: [email protected] 7106504648 REV1.0.0
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
Installation Guide
Outdoor CPE
CPE210 / CPE220 / CPE510 / CPE520