TP-Link Archer MR400 Archer MR400EU V1 Quickk Installation Guide - Page 2

Customize the 4G LTE Router 1. Make sure your computer is connected to the router (via wired or wireless). 2. Launch a web browser and type in http://tplinkmodem.net or 192.168.1.1. Create a new password and click Let's Get Started. Note: If the login page does not appear, please refer to FAQ > Q1. http://tplinkmodem.net New Password Low Middle High Confirm Password Let's Get Started 3. Follow the step-by-step instructions of the Quick Setup to complete the initial configuration. On the Wireless Settings page, you can customize your 2.4GHz and 5GHz wireless network names and passwords. 2.4GHz Wireless: Network Name (SSID): Password: 5GHz Wireless: Network Name (SSID): Password: Enable Wireless Radio TP-Link_XXXX XXXXXXXX Enable Wireless Radio TP-Link_XXXX_5G XXXXXXXX Back Next Note: The router can also be used (or configured) in Wireless Router Mode for ADSL/Cable connections. For more advanced configurations, please refer to the User Guide on TP-Link official website at www.tp-link.com. LED Indicators LED Status Indication (Power) (Internet) (4G) (Wireless) (LAN) (WPS) (Signal Strength) On Off On Off On Off On Off On Off On/Off Flashing On Off Power is on. Power is off. The router is connected to the internet. There is no internet connection. The router is connected to the 4G network. The router is disconnected from the 4G network. At least one wireless radio band (2.4GHz or 5GHz) is enabled. The wireless radio band is disabled. At least one LAN port is connected to a powered-on device. No LAN port is connected to a powered-on device. This light remains on for 5 minutes when a WPS connection is established, then turns off. WPS connection is in progress. This may take up to 2 minutes. Indicates the signal strength received from the mobile internet network. More lit bars indicate a better signal strength. There is no mobile internet signal. Tether App To manage your network conveniently on your mobile device, scan the QR code to download the Tether App. FAQ (Frequently Asked Questions) Q1. What should I do if I cannot access the web management page? A1. If the computer is set to a static IP address, change its settings to obtain an IP address automatically. A2. Make sure http://tplinkmodem.net or http://192.168.1.1 is correctly entered in the web browser. A3. Use another web browser and try again. A4. Reboot your router and try again. A5. Disable and enable the active network adapter in use. Q2. What should I do if I cannot access the internet? A1. Verify that your SIM card is an LTE, WCDMA or GSM card. A2. Verify that your SIM card is in your internet service provider's service area. A3. Verify that your SIM card has sufficient credit. A4. Check the LAN connection: Open a web browser and enter http://tplinkmodem.net or http://192.168.1.1 in the address bar. If the login page does not appear, refer to FAQ > Q1 and then try again. A5. Check your ISP parameters: 1) Open a web browser and log in to the web management page. 2) Go to Advanced > Network > Internet to verify the parameters (including the APN, Username and Password) provided by your ISP are correctly entered. If the parameters are incorrect, click Create Profile and enter the correct parameters, then select the new profile from the Profile Name list. A6. Check the PIN settings: 1) Open a web browser and log in to the web management page. 2) Go to Advanced > Network > PIN Management to verify if PIN is required. If it is, enter the correct PIN provided by your ISP, and click Apply. A7. Check the Data Limit: 1) Open a web browser and log in to the web management page. 2) Go to Advanced > Network > Data Settings to verify if the Total/Monthly Used exceeds the Total/Monthly Allowance. If it does, click Correct and set Total/Monthly Used to 0 (zero), or disable Data Limit. A8. Check the Mobile Data: 1) Open a web browser and log in to the web management page. 2) Go to Advanced > Network > Internet to verify that Mobile Data is enabled. If it is not, enable it to access the internet. A9. Check the Data Roaming: 1) Confirm with your ISP if you are in a roaming service area. If you are, open a web browser and log in to the web management page. 2) Go to Advanced > Network > Internet to enable Data Roaming. Q3. How do I restore the router to its factory default settings? A1. With the router powered on, press and hold the WPS/RESET button on the rear panel of the router until all the LEDs except the Power LED turn on momentarily, then release the button. Wait while the router resets. A2. Log in to the web management page of the router, and go to Advanced > System Tools > Backup & Restore, click Factory Restore and wait until the reset process is complete. WPS/RESET Button Q4. What should I do if I forget my web management page password? A. Refer to FAQ > Q3 to reset the router, and then set a new password. Q5. What should I do if I forget my wireless network password? A1. The default Wireless Password is printed on the product label of the router. A2. If the default Wireless Password has been changed, log in to the router's web management page and go to Basic > Wireless to retrieve or reset your password. For technical support and other information, please visit http://www.tp-link.com/support, or simply scan the QR code. 7106507241 REV1.0.0 ©2017 TP-Link