TP-Link T2600G-28TS TL-SG3424 T2600G-28TS V1 Installation Guide
TP-Link T2600G-28TS TL-SG3424 Manual
View all TP-Link T2600G-28TS TL-SG3424 manuals
Add to My Manuals
Save this manual to your list of manuals |
TP-Link T2600G-28TS TL-SG3424 manual content summary:
- TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 1
Business Networking Solution Installation Guide Gigabit L2 Managed Switch T2600G-28TS (TL-SG3424) T2600G-52TS (TL-SG3452) - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 2
- TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 3
. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 4
: http://www.tp-link.com About this Installation Guide This Installation Guide describes the hardware characteristics, installation methods and the switch. Chapter 5 Configuration. This chapter instructs you to configure the switch via Web Interface and CLI commands. Appendix A Troubleshooting. - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 5
Due to the similarity in the structure of the L2 Managed Switch series, in this Installation Guide we take T2600G-28TS as an example to illustrate Chapter 2 Installation, Chapter 3 Lightning Protection and Chapter 4 Connection. This guide uses the specific formats to highlight special messages. The - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 6
Port 14 4.3 Console Port 15 4.4 Verify Installation 16 4.5 Power On 17 4.6 Initialization 17 Chapter 5 Configuration 18 5.1 Configure the Switch via GUI 18 5.2 Configure the Switch Using CLI 19 Appendix A Troubleshooting----------- 22 Appendix B Hardware Specifications------- 24 IV Contents - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 7
large and medium-sized network. Designed for workgroups and departments, T2600G-28TS/T2600G-52TS from TP-LINK provides wire-speed performance and full set of L2 management features. It provides a variety of service features and multiple powerful functions with high security. The EIA-standardized - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 8
the USB port of a computer for monitoring and configuring the switch. The switch has an RJ-45 console port and a micro-USB console to install the SFP module. T2600G-28TS features 4 individual SFP ports and supports 1000M SFP module connection only. The front panel of T2600G-52TS is shown as the - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 9
the USB port of a computer for monitoring and configuring the switch. The switch has an RJ-45 console port and a micro-USB console the SFP module. T2600G-52TS features 4 individual SFP ports and supports 1000M SFP module connection only. Port Feature Model T2600G-28TS T2600G-52TS 10/100/1000Mbps - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 10
Rear Panel of T2600G-28TS Power Socket Connect the female connector of the power cord here, and the male connector to the AC power outlet. Please make sure the voltage of the power supply meets the requirement of the input voltage (100-240V~ 50/60Hz). Grounding Terminal The switch already comes with - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 11
items. If any of the listed items is damaged or missing, please contact your distributor. One Switch One Power Cord, One Console Installation Guide Cable and One USB Cable T2600-28TS One Resource CD Two Mounting Brackets and the Fittings 2.2 Safety Precautions To avoid any device damage and - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 12
of the insulation materials and can thus significantly shorten the service life of the device. For normal temperature and humidity %RH Non-condensing 5% ~ 90%RH Non-condensing Clearness T2600-28TS The dust accumulated on the Switch can be absorbed by static electricity and result in poor contact of - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 13
Managed Switch instant current please refer to Chapter 3 Lightning Protection. Installation Site T2600-28TS When installing the device on a rack or a flat : ■■ The rack or workbench is flat and stable, and sturdy enough to support the weight of 5.5kg at least. ■■ The rack or workbench has a good - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 14
T2600-28TS Gigabit L2 Managed Switch 3. Turnover the device and attach the supplied rubber feet to Rack Installation To install the device in an EIA standard-sized, 19-inch rack, follow the instructions described below: 1. Check the grounding and stability of the rack. 2. Secure the supplied rack- - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 15
Gigabit L2 Managed Switch Chapter 3 Lightning Protection 3.1 Cabling Reasonably In the actual network environment, you may need cable outdoors and indoors, and the requirements for cabling outdoors and indoors - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 16
Gigabit L2 Managed Switch ■■ Requirements for the distance between Ethernet cable and other pipelines are shown in the table. Other Pipelines Ethernet Cable Min Parallel Net Length Min Parallel-overlapping Net Height L (mm) H (mm) Down-conductor 1000 300 PE 50 20 Service pipe 150 20 - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 17
different environments, the device may be grounded differently. The following will instruct you to connect the device to the ground in two ways, connecting shown in the following figure. 100-240V~50/60Hz 0.5A Switch (Rear Panel) Ground Cable Grounding Terminal Grounding Bar Figure 3-1 Connecting - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 18
Gigabit L2 Managed Switch Note: ■■ The figure is to illustrate the application and principle. The power cord you get from the package and the socket in your situation will - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 19
Gigabit L2 Managed Switch 3.4 Use Lightning Arrester Power lightning arrester and signal lightning arrester device and connect it to the ground via a shorter ground cable. T2600-28TS Grounding Terminal Signal Lightning Arrester Equipotential Bonding Cable Device Ethernet Cable Figure 3-4 - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 20
Chapter 4 Connection 4.1 Ethernet Port Connect the Ethernet ports of the switch to the network devices by RJ45 cable as the following figure shows. RJ45 Port T2600-28TS RJ45 Cable Figure 4-1 Connecting the RJ45 Port 4.2 SFP Port Figure 4-2 demonstrates the connection of SFP port to an SFP module - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 21
1,050 meters that is 3,440 feet. T2600G-28TS and T2600G-52TS are compatible with all kinds of table shows the detailed information of two SFP modules (TL-SM311LS and TL-SM311LM) produced by TP-LINK, which makes you Interface) enables you to manage the switch, thus you can load the CLI after connecting the - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 22
by the USB cable as the following figure shows. Console(USB) T2600-28TS Figure 4-5 Connecting the Console (USB) Port You can also manage the device through the console port, for details please refer to the CLI Reference Guide on the resource CD. Note: ■■ Console (RJ-45) port and Console (USB - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 23
Gigabit L2 Managed Switch 4.5 Power On Plug the female connector of the provided power cord into the power socket of the device, and the male connector into a power outlet - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 24
set in the same subnet addresses of the switch. The IP address is 192.168.0.x ("x" is any number from 2 to 254), Subnet Mask is 255.255.255.0. For the detailed instructions as to how to do this, please refer to Appendix B in the User Guide on the Resource CD. 2. Enter admin for the - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 25
to the User Guide to learn more about the installation. To log on to the switch by the console port on the switch, please take the Parity: none ■■ Stop bits: 1 ■■ Flow control: none 5. The DOS prompt "T2600G-28TS>" will appear after pressing the Enter button as Figure 5-4 shows. It indicates that - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 26
refer to the CLI Reference Guide on the resource CD. Here we take login local mode as an example. 2. Make sure the switch and the PC are prompt shown as Figure 5-6, and press the Enter button. Figure 5-6 Connecting the Switch 5. Type the default user name and password (both of them are admin), then - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 27
Gigabit L2 Managed Switch Appendix A Troubleshooting Q1. What could I do if I forgot the username and password of the switch? 1. Connect the console port of the PC to the console port of the switch and open a terminal emulation program. 2. Power off and restart the switch. When you are prompted that - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 28
Gigabit L2 Managed Switch Q4. Why does the terminal emulation program display abnormally? Please check as follows: 1. Make sure the power supply is normal and the correct: configure Bits per second as 38400, Data bits as 8, Parity as None, Stop bits as 1, and Flow control as None. 22 Troubleshooting - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 29
Gigabit L2 Managed Switch Appendix B Hardware Specifications Item Content IEEE 802.3 10Base-T IEEE . 5e, and Cat. 6 or above 1000Base-X: MMF or SMF SFP Module (Optional) LEDs T2600G-28TS: PWR, SYS, 1000Mbps, Link/Act T2600G-52TS: PWR, SYS, 10/100/1000Mbps (Port 1-48), Link/Act (Port 49-52) - TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 30
- TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 31
- TP-Link T2600G-28TS TL-SG3424 | T2600G-28TS V1 Installation Guide - Page 32
Website: http://www.tp-link.com Tel: +86 755 26504400 E-mail: [email protected] 7106505249 REV1.0.0
Installation Guide
Gigabit L2 Managed Switch
T2600G-28TS (TL-SG3424)
T2600G-52TS (TL-SG3452)
Business Networking Solution