TP-Link TL-SF1005P TL-SF1005PUN V1 Installation Guide - Page 2

Frequently Asked Questions (FAQ) Q1. Why is the Power LED not lit? The Power LED should be lit when the power system is working normally. If the Power LED is not lit, please try the following: A1: Make sure the AC power cord is connected to the switch with power source properly. A2: Make sure the voltage of the power supply meets the requirements of the input voltage of the switch. A3: Make sure the power source is ON. Q2. Why is the Link/Act LED not lit while a device is connected to the corresponding port? Please try the following: A1: Make sure that the cable connectors are firmly plugged into the switch and the device. A2: Make sure the connected device is turned on and works normally. A3: The cable must be less than 100 meters long (328 feet). Q3. Why is port 4 not supplying power for PoE devices? If connected PoE device's total power consumption exceeds 58W, the system will cut off the power to port 4. For example, port 1, 2 and 4 are consuming 15.4W respectively, if an additional PoE device with 12W is inserted to port 3, the system will cut off the power of port 4 to compensate for the overload. Specifications General Specifications Standard Protocol Interface Network Media (Cable) Switching Capacity MAC Address Table Transfer Method MAC Address Learning Power Supply IEEE802.3i, 802.3u, 802.3x, 802.3af CSMA/CD 5 10/100Mbps RJ45 Ports, Auto-Negotiation MDI/MDIX PoE Ports: Port1-Port4, Total Power Supply:58W 10BASE-T: UTP category 3, 4, 5 cable (maximum 100m); EIA/TIA-568 100Ω STP (maximum 100m) 100BASE-TX: UTP category 5, 5e cable (maximum 100m); EIA/TIA-568 100Ω STP (maximum 100m) 1Gbps 2K Store-and-Forward Automatically learning, automatically aging External Power Adapter Input: 100-240VAC, 50/60Hz Output: 48VDC /1.25A Environmental and Physical Specifications Operating Temperature 0˚C to 40˚C (32˚F to 104˚F) Storage Temperature -40˚C to 70˚C (-40˚F to 158˚F) Operating Humidity Storage Humidity 10% to 90%RH non-condensing 5% to 95%RH non-condensing For technical support and other information, please visit http://www.tp-link.com/support, or simply scan the QR code. FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. BSMI Notice b b a b b b b b b CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. SAFETY NOTICES Cautions Do not use this product near water, for example, in a wet basement or near a swimming pool. Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC and 2011/65/EU. The original EU declaration of conformity may be found at http://www.tp-link.com/en/ce. Explanation of the symbols on the product label DC voltage Indoor use only RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment. Industry Canada Statement CAN ICES-3 (B)/NMB-3(B) © 2017 TP-Link