TP-Link TL-SF1024M TL-SF1024M V1 Quick Install Guide - Page 2

Frequently Asked Questions (FAQ) Q1. The Power LED is not lit The Power LED should be lit when the power system is working normally. If the Power LED is not lit, please check as follows: A1: Make sure the power cord is connected to the switch with power source properly. A2: Make sure the voltage of the power supply meets the requirements of the input voltage of the switch. A3: Make sure the power source is ON. Q2. The Link/Act LED is not lit when a device is connected to the corresponding port. It is recommended that you check the following items: A1: Make sure that the cable connectors are firmly plugged into the switch and the device. A2: Make sure the connected device is turned on and working well. A3: The cable must be less than 100 meters long (328 feet). General Specifications Standard IEEE 802.3,IEEE 802.3i, IEEE 802.3u,
IEEE 802.3x Protocol CSMA/CD Interface 24 10/100Mbps Auto-Negotiation RJ45 Ports 10BASE-T: UTP category 3, 4, 5 cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m) Network Media (Cable) 100BASE-TX: UTP category 5, 5e cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m) LED indicators Power, Link/Act LEDs Data Transfer Rate Ethernet: 10Mbps (Half Duplex), 20Mbps (Full Duplex) Fast Ethernet: 100Mbps (Half Duplex), 200Mbps (Full Duplex) Transfer Method Store-and-Forward MAC Address Learning Automatically learning, automatically aging Frame Filter Rate 10Base-T: 14880pps/Port 100Base-Tx: 148800pps/Port Frame Foward Rate 10Base-T: 14880pps/Port 100Base-Tx: 148800pps/Port Environmental and Physical Specifications Certification FCC, CE, RoHS Operating Temperature 0˚C~40˚C (32˚F~104˚F) Storage Temperature -40˚C~70˚C (-40˚F~158˚F) Operating Humidity 10%~90% non-condensing Storage Humidity 5%~90% non-condensing SAFETY NOTICES Cautions Do not use this product near water, for example, in a wet basement or near a swimming pool. Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, FCC STATEMENT transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2015 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.com CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.