TP-Link TL-SG105E TL-SG105E V1 QIG - Page 2

LED Explanation 1000M (Green) On: Connected to a 1000Mbps device Flashing: Transmitting/receiving data 10/100M (Yellow) On: Connected to a 10/100Mbps device Flashing: Transmitting/receiving data Power On: Power on Off: Power off Frequently Asked Questions (FAQ) Q1. The Power LED is not lit The Power LED should be lit when the power system is working normally. If the Power LED is not lit, please check as follows: A1: Make sure the power adapter is connected to the switch with power source properly. A2: Make sure the voltage of the power supply meets the requirements of the input voltage of the switch. A3: Make sure the power source is ON. Q2. The Link/Act LED is not lit when a device is connected to the corresponding port It is recommended that you check the following items: A1: Make sure that the cable connectors are firmly plugged into the switch and the device. A2: Make sure the connected device is turned on and works normally. A3: The cable must be less than 100 meters long (328 feet). Environmental and Physical Specifications Operating Temperature Storage Temperature Operating Humidity Storage Humidity 0˚C~40˚C (32˚F~104˚F) -40˚C~70˚C (-40˚F~158˚F) 10%~90% non-condensing 5%~90% non-condensing General Specifications Standard Protocol Data Transfer Rate Network Media (Cable) Interface LED indicators Transfer Method MAC Address Learning Frame Filter Rate Frame Forward Rate IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3x, IEEE802.1p, IEEE802.1q CSMA/CD Ethernet: 10Mbps (Half Duplex) 20Mbps (Full Duplex) Fast Ethernet: 100Mbps (Half Duplex) 200Mbps (Full Duplex) Gigabit Ethernet: 2000Mbps (Full Duplex) 10Base-T: UTP category 3, 4, 5 cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m) 100Base-TX: UTP category 5, 5e cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m) 1000Base-T: UTP category 5 cable (maximum 100m) EIA/TIA-568 100Ȥ STP (maximum 100m) 5/8 10/100/1000Mbps Auto-Negotiation RJ45 Ports Power, 10/100M LED, 1000M LED Store-and-Forward Automatically learning, automatically aging 10Base-T: 14881pps/Port 100Base-Tx: 148810pps/Port 1000Base-T: 1488095pps/Port 10Base-T: 14881pps/Port 100Base-Tx: 148810pps/Port 1000Base-T: 1488095pps/Port SAFETY NOTICES Cautions Do not use this product near water, for example, in a wet basement or near a swimming pool. Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, FCC STATEMENT transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2014 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.com CE Mark Warning This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.