Home » TP-Link Manuals » Hubs & Switches » TP-Link TL-SL2428WEB » Manual Viewer

TP-Link TL-SL2428WEB User Guide - Page 57

TP-Link TL-SL2428WEB Manual

UPC - 845973020361

View all TP-Link TL-SL2428WEB manuals

Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide "aging time". Further Explanation 1) The aging time ranges from 0 to 3825 seconds. An appropriate aging time should be configured here. An aging time that is too long lengthens the time of the dynamic MAC address being deleted and further causes the packets to be forwarded incorrectly. An aging time that is too short causes the table entries to be deleted quickly. Some packets have to be broadcasted because no corresponding entries can be abided by. The efficiency of packet forwarding is reduced. 2) The MAC addresses in static MAC address table, filtering MAC address table and bound MAC address table are free of the aging time. 5.3.3.7 Ping The ping function is to test the connectedness of the link between the switch and destination. This page is showed as below: Figure 5-34 Ping  Destination IP Address: Indicates the IP Address of the test destination.  Ping Count: Indicates the ping times in one submission.  Data Size: Indicates the data field length of ping packet.  Ping Interval: Indicates the time interval between two continuous pings. 50

Section	Page
Package contents	8
Chapter 1: Introduction	9
1.1 Intended Audience	9
1.2 Agreement	9
1.3 Guide Overview	9
Chapter 2: Device Description	11
2.1 Introduction to the Device	11
2.2 Features and Technical Specifications	11
2.2.1 Features	11
2.2.2 Technical Specifications	12
Chapter 3: Mounting Device	14
3.1 Install the Device	14
3.1.1 Desktop or Shelf Installation	14
3.1.2 Rack Installation	14
3.1.3 AC Power	15
3.2 Switch Aspect Description	15
3.2.1 Front Panel	15
3.2.2 Back Panel	17
3.2.3 SFP Module	17
3.3 Note	18
Chapter 4: Function Description	19
4.1 System Setting	19
4.1.1 System Information	19
4.1.2 File Transfer	19
4.1.3 Reboot & Reset	19
4.1.4 User	20
4.2 Port Setting	20
4.2.1 Port Parameter	20
4.2.1.1 Duplex Mode	20
4.2.1.2 Flow Control	20
4.2.1.3 Port Security	20
4.2.2 Port Statistic and Port Status	21
4.2.3 Storm Control	21
4.2.4 Port Description	22
4.3 Network Setting	22
4.3.1 Switch IP Address	22
4.3.2 Aging Time and Dynamic Address Table	23
4.3.3 Static MAC Address Table	23
4.3.4 Filtering MAC Address Table	24
4.3.5 Dynamic Binding	24
4.3.6 Ping	25
4.4 VLAN Setting	25
4.4.1 VLAN Mode	26
4.5 Port Trunking	27
4.6 Priority Setting	27
4.6.1 Priority Mode	27
4.6.2 Port-Based Priority	28
4.6.3 Port Default Priority	28
4.6.4 802.1p Priority	28
4.7 Port Mirroring	28
4.8 Virtual Cable Test	29
Chapter 5: WEB Management	30
5.1 Overview	30
5.2 Connecting to the Device	30
5.2.1 Getting Started	30
5.2.2 Login the Switch	34
5.3 Setting the Device	34
5.3.1 System Setting	39
5.3.1.1 System Information	39
5.3.1.2 File Transfer	40
5.3.1.3 Reboot & Reset	41
5.3.1.4 User	42
5.3.2 Port Setting	43
5.3.2.1 Port Parameter	43
5.3.2.2 Port Statistic	44
5.3.2.3 Port Status	46
5.3.2.4 Storm Control	47
5.3.2.5 Port Description	48
5.3.3 Network Setting	48
5.3.3.1 Switch IP Address	49
5.3.3.2 Static MAC Address	50
5.3.3.3 Filtering MAC Address	52
5.3.3.4 Dynamic Binding	53
5.3.3.5 Bound MAC Address	55
5.3.3.6 Aging Time	56
5.3.3.7 Ping	57
5.3.4 VLAN Setting	58
5.3.4.1 VLAN Mode	58
5.3.4.2 Port VLAN Setting	58
5.3.4.3 Tag VLAN Global Setting	60
5.3.4.4 Tag VLAN Setting	61
5.3.4.5 MTU VLAN Setting	63
5.3.5 Port Trunking	63
5.3.6 Priority Setting	64
5.3.6.1 Priority Mode	65
5.3.6.2 Port-Based Priority	65
5.3.6.3 Port Default Priority	66
5.3.6.4 802.1p Priority Class	66
5.3.7 Port Mirroring	67
5.3.8 Virtual Cable Test	68
Appendix A Pin Explain For RJ-45 Connector	70
Appendix B Table of Factory Defaults	72