TP-Link TL-WPA4220KIT TL-WPA4220KIT V1 QIG - Page 2

Method 2: Setup via Wi-Fi Clone Extend the Router's Wireless Network 1. Plug TL-WPA4220 into a wall socket near your router. Wireless Router ( supporting WPS ) AV500 TL-WPA4220 Blink quickly in about 15 seconds. AV500 2. Press the WPS button on your router, and within 1 minute, press the Wi-Fi Clone button on your TL-WPA4220. WPS Wireless Router AV500 TL-WPA4220 • Blink every second after pressing the Wi-Fi Clone button. • Blink quickly within 1 minute when Wi-Fi Clone is completed. AV500 TL-WPA4220 will automatically copy the wireless network name and password of the router when Wi-Fi clone is completed. 3. Connect your devices as follows. SSID: ABCDE Internet TL-PA4010 LAN WAN SSID: ABCDE AV500 TL-WPA4220 All the Powerline LEDs will turn solid within 1 minute. Enjoy! Use the router's SSID (ABCDE) and password to access the Internet. If the Powerline LEDs don't turn solid, reset all the powerline devices, or create a powerline network by referring to FAQ->Q1. Read this to install additional devices 1. Make sure the additional devices are factory default settings. If not, please reset them. 2. If the additional devices have Wi-Fi Clone function, follow step 1 and 2 of Method 2 to install them. If not, skip this. 3. Plug them into the outlets and wait about 1 minute until their Powerline LEDs turn solid. TL-PA4010 AV500 TL-WPA4220 Installation is completed when all the Powerline LEDs turn solid. AV500 Additional Device If the Powerline LEDs do not turn solid, please follow the instructions in FAQ->Q1: 1. For the two devices connected before, use the Pair Button to create a powerline network (Q1->A). (Skip this step if you have already done this.) 2. For additional devices, use the Pair Button to join the existing powerline network (Q1->B). FAQ (Frequently Asked Questions) Q1. How do I use the Pair button to create or join a powerline network? You can use the Pair button on only two devices at a time. A. To create a powerline network 1. Press the Pair button on TL-WPA4220. The Power LED will blink. 2. Within 2 minutes, press the Pair button on TL-PA4010. The Power LED will blink. 3. In about 1 minute, all the Powerline LEDs will turn solid. B. To join an existing powerline network 1. Press the Pair button on a third powerline device. The Power LED will blink. 2. Within 2 minutes, press the Pair button on either TL-PA4220 or TL-PA4010 you have paired. The Power LED will blink. 3. In about 1 minute, all the Powerline LEDs will turn solid. Q2. How do I reset TL-WPA4220? With TL-WPA4220 turned on, use a pin to press and hold the Reset button for more than 5 seconds. The Power LED will be o momentarily before turning solid and the Wi-Fi LED will blink quickly. This indicates that the reset process is completed. Q3. How do I customize the wireless settings on the web management page? 1. Find the utility on the provided CD (for Windows only) or download it from our o cial website. 2. Open the utility and click 'Connect'. 3. Log in to the web management page using the default user name and password (admin/admin). 4. Con gure the SSID and click 'Save' on the 'Wireless>Wireless Settings' page. 5. Con gure the password and click 'Save' on the 'Wireless> Wireless Security' page. 6. Click 'click here' at the page bottom to reboot the extender. Q4. What can I do if my computer can't access the Internet after it is connected to a powerline adapter/extender? Check the following: 1. Connect your computer to the modem or router to test the Internet connection. 2. Make sure the hardware connection is correct. 3. Make sure the Powerline LEDs light up on all of your adapters/extenders. If not, create or join a powerline network by referring to FAQ-Q1. 4. Make sure your computer is set to 'Obtain an IP address automatically'. If your computer still can't access the Internet after following these steps, please contact our technical support. For more information about the advanced settings, please refer to the User Guide.