TRENDnet TEW-676APBO User's Guide

TRENDnet TEW-676APBO Manual

Get TRENDnet TEW-676APBO PDF manuals and user guides View all TRENDnet TEW-676APBO manuals
Add to My Manuals
Save this manual to your list of manuals

TRENDnet TEW-676APBO manual content summary:

  • TRENDnet TEW-676APBO | User's Guide - Page 1
    TRENDnet User's Guide Table of Contents
  • TRENDnet TEW-676APBO | User's Guide - Page 2
    TRENDnet User's Guide Contents Introduction ...5 Features ...5 Package Contents ...5 Hardware Feature...6 System Concept...7 12 Web Management Interface Instructions 13 AP Mode Configuration 13 External Network Connection 14 Network Requirement 14 Configure LAN IP ...14 Wireless LAN Network
  • TRENDnet TEW-676APBO | User's Guide - Page 3
    TRENDnet User's Guide QoS Setup...48 Resource Sharing ...50 DMZ...50 Virtual Server (Port Network Creation 68 Repeater AP Setup 68 Wireless MAC Filter Setup 70 Access Control List ...70 IP Filter Setup ...70 MAC Filter Setup ...71 Parental Control Setup 72 QoS Setup...73 Resource Sharing
  • TRENDnet TEW-676APBO | User's Guide - Page 4
    TRENDnet User's Guide Wireless LAN Network Creation 102 Wireless General Setup 102 Wireless Advanced Setup 103 Create Virtual AP (VAP 107 Wireless MAC Filter Setup 110 Wireless Network Expansion 111 Access Control List ...112 IP and Reset to Factory 127 Firmware Upgrade 128 Network Utility
  • TRENDnet TEW-676APBO | User's Guide - Page 5
    support for device configuration of Internet applications © Copyright 2012TRENDnet. All Rights Reserved. TEW-676APBO • Complete wireless security with WPA/WPA2-RADIUS, WPA /WPA2-PSK, and WEP • Multiple pass-through sessions for popular VPN applications (IPSec, L2TP, and PPTP) • Quality of Service
  • TRENDnet TEW-676APBO | User's Guide - Page 6
    TRENDnet User's Guide Hardware Feature Front Panel Housing • Housing - IP 66/67 housing © Copyright 2012TRENDnet. All Rights Reserved. Bottom Panel TEW-676APBO for more than 10 seconds to restore the unit back to factory default settings. • PoE Port (unscrew cap) - Connect the network cable
  • TRENDnet TEW-676APBO | User's Guide - Page 7
    TRENDnet User's Guide System Concept The TEW-676APBO is not only designed and used as a traditional outdoor AP, but also with rich features tailored indoor and outdoor grounds in private resorts, home yards, or gulf course communities. © Copyright 2012TRENDnet. All Rights Reserved. TEW-676APBO 7
  • TRENDnet TEW-676APBO | User's Guide - Page 8
    TRENDnet User's Guide Product Benefit The N300 Wireless 12dBi Outdoor 5GHz PoE Access Point is the point of connection to Wireless Outdoor Network for service provider deploying last mile services service tier using per-subscriber rate limiting features, and manage centrally. TEW-676APBO the range of
  • TRENDnet TEW-676APBO | User's Guide - Page 9
    TRENDnet User's Guide Installation 1. Unscrew the black cap covering the PoE port of the TEW-676APBO 2. Install the waterproof kit and insert one end of an Ethernet cable through the kit. TEW-676APBO 3. Connect the Ethernet cable to the PoE port of the TEW-676APBO 7. Connect the other end of the
  • TRENDnet TEW-676APBO | User's Guide - Page 10
    TRENDnet User's Guide Applications TEW-676APBO is multiple mode system which can be configured either as AP Mode, WDS Mode, CPE Mode, Client Bridge + Universal Repeater Mode and CPE + AP Mode. TEW-676APBO Remote Bass WDS : Router AP Mode (Gateway + Access Point + WDS) Example 1 : Router AP without
  • TRENDnet TEW-676APBO | User's Guide - Page 11
    TRENDnet User's Guide  Example 2 : Access Point with WDS  It can be deployed as a tradition fixed wireless Access Point and provides WDS link to expand network Remote Main WDS TEW-676APBO to a network wirelessly. In this mode, it can support single or multiple WDS links and no wireless clients can
  • TRENDnet TEW-676APBO | User's Guide - Page 12
    TRENDnet User's Guide  Example 3 : Multi-Point Repeating bridge Inter NA Main Base WIFI WAN LAN Station TEW-676APBO Client service to residents and business customers. In the CPE mode, TEW676APBO is a gateway enabled with NAT and DHCP Server functions. The wired clients connected to TEW-676APBO
  • TRENDnet TEW-676APBO | User's Guide - Page 13
    TRENDnet User's Guide Web Management Interface Instructions TEW-676APBO supports web-based configuration. Upon the completion of hardware installation, TEW-676APBO can be configured through a PC/NB by using its web browser such as Internet Explorer version 6.0.  Default IP Address : 192.168.10.
  • TRENDnet TEW-676APBO | User's Guide - Page 14
    manually setup the LAN IP address when static IP is available/ preferred.  IP Address : The IP address of the LAN port; default IP address is 192.168.2.254  IP Netmask : The Subnet mask of the LAN port; default Netmask is 255.255.255.0 © Copyright 2012TRENDnet. All Rights Reserved. TEW-676APBO
  • TRENDnet TEW-676APBO | User's Guide - Page 15
    TRENDnet User's Guide © Copyright 2012TRENDnet. All Rights Reserved. WDS Remote Base Station LOOP WDS WDS Blocked by Spanning Tree Protocol TEW-676APBO Remote Base Station WDS Remote Base Station LOOP WDS Blocked by Spanning Tree Protocol Base Station WDS Remote Base Station 15
  • TRENDnet TEW-676APBO | User's Guide - Page 16
    TRENDnet User's Guide Reserved. TEW-676APBO unit is %) for your environment. If you are not sure which setting to choose, then keep the default setting, 100 Default is enabled.  A-MSDU : Aggregated Mac Service Data Unit. Select Enable to allow aggregation for multiple MSDUs in one MPDU Default
  • TRENDnet TEW-676APBO | User's Guide - Page 17
    TRENDnet User's Guide  Short Slot : By default, it's "Enable" for reducing the range of 1~255 and set in unit of microsecond. The default value is 32 microsecond. All data transmission in 802.11b/g request an "Acknowledgement" (ACK) send by © Copyright 2012TRENDnet. All Rights Reserved. TEW-676APBO
  • TRENDnet TEW-676APBO | User's Guide - Page 18
    TRENDnet User's Guide  Fragment Threshold : The Fragment Threshold is in the range of 256~2346 byte. The default default, it's "Disable". To Enable is to use WMM and the WMM parameters should appears. © Copyright 2012TRENDnet. All Rights Reserved. TEW-676APBO queue traditional IP AC_VI AC_VO
  • TRENDnet TEW-676APBO | User's Guide - Page 19
    TRENDnet User's Guide applications, and rely on best-effort parameters for traditional IP data. As an Example, time-sensitive Voice & Video, and multimedia are given effectively higher priority for transmission (lower wait times for channel access), while other applications and traditional IP data
  • TRENDnet TEW-676APBO | User's Guide - Page 20
    TRENDnet User's Guide and delay. Most data is sent to this queue traditional IP AC_VI Video High Minimum delay. Time-sensitive video data is to all VAPs and WDS Links. TEW-676APBO Create Virtual AP (VAP) The TEW-676APBO support broadcasting multiple SSIDs, allowing the creation
  • TRENDnet TEW-676APBO | User's Guide - Page 21
    TRENDnet User's Guide TEW-676APBO  Enable AP : By default, it's "Disable" for VAP1 ~ VAP6. The Primary AP always enabled. Select "Enable" to activate VAP or click "Disable" to deactivate this function  ESSID : Extended Service By default, it's selected "Disable". This system supports tagged
  • TRENDnet TEW-676APBO | User's Guide - Page 22
    TRENDnet User's Guide 64-bit or 128-bit shared key. TEW-676APBO  Cipher Suite : By default, it is AES. Select either AES or ASCII format WEP key value; the system supports up to 4 sets of WEP keys. Key Length IP Address : Enter the IP address of the Authentication RADIUS server. • Port : By default
  • TRENDnet TEW-676APBO | User's Guide - Page 23
    TRENDnet User's Guide • Session Timeout : The Session timeout is in the range of 0~60 seconds. The default is 0 to disable re-authenticate service. • Amount of time before a client will be required to re-authenticate.  WEP 802.1X : When WEP 802.1x Authentication is enabled, please refer to the
  • TRENDnet TEW-676APBO | User's Guide - Page 24
    Guide Wireless Network Expansion The administrator could create WDS Links to expand wireless network. When WDS is enabled, access point functions as a wireless bridge and is able to communicate with other access points via WDS links. A WDS link is bidirectional and both side must support TEW-676APBO
  • TRENDnet TEW-676APBO | User's Guide - Page 25
    has been in service since last reboot.  Network Information : Supports Static or Dynamic modes on the LAN interface. TEW-676APBO  Wireless Information : Display total received and transmitted statistics on available Virtual AP.  IP Address : The management IP of system. By default, it's 192.168
  • TRENDnet TEW-676APBO | User's Guide - Page 26
    TRENDnet User's Guide TEW-676APBO  VAP Information : Highlights key VAP information.  VAP : Available VAP from period in seconds for a wireless connection.  Disconnect : Click "Delete" button to manually disconnect a wireless client in a Virtual AP. Show WDS Link Status Peers MAC Address,
  • TRENDnet TEW-676APBO | User's Guide - Page 27
    TRENDnet User's Guide TEW-676APBO could be used as a L2 or L3 device. It doesn't support dynamic routing protocols such as RIP or OSPF. Static routes to specific hosts, networks or default gateway are set up automatically according to the IP configuration of system's interfaces. When used as a L2
  • TRENDnet TEW-676APBO | User's Guide - Page 28
    TRENDnet User's Guide © Copyright 2012TRENDnet. All Rights Reserved. TEW-676APBO Event Log The Event log displays system events when system is up and running. Also, it becomes very useful as a troubleshooting tool when issues are experienced in system.  Time : The date and time when the event
  • TRENDnet TEW-676APBO | User's Guide - Page 29
    via a WDS link as shown in Figure 4-1. In the mode, it can't associate with any wireless clients. WDS TEW-676APBO Configure LAN IP Here are the instructions for how to setup the local IP Address and Netmask. Please click on System -> LAN and follow the below setting.  Mode : Check either "Static
  • TRENDnet TEW-676APBO | User's Guide - Page 30
    TRENDnet User's Guide follow the below setting. TEW-676APBO  MAC Address : The drop-down list; the options are auto or ranging from 6 to 54Mbps only for 802.11a Default is enabled.  A-MSDU : Aggregated Mac Service Data Unit . Select Enable to allow aggregation for multiple MSDUs in one MPDU Default
  • TRENDnet TEW-676APBO | User's Guide - Page 31
    TRENDnet User's Guide TEW-676APBO improve performance.  Extra Slot Time : Slot time is in the range of 1~255 and set in unit of microsecond. The default range of 1~255. The default is 1. DTIM is defined as Delivery Traffic Indication Message. It is used to notify the wireless stations, which support
  • TRENDnet TEW-676APBO | User's Guide - Page 32
    TRENDnet User's Guide in the range of 1~2347 byte. The default is 2347 default, RTS is disabled in a normal environment supports non-jumbo frames.  Short Preamble : By default TEW-676APBO with the fixed overhead cost of just a single frame.  WMM : By default delay. Most traditional IP data is sent to
  • TRENDnet TEW-676APBO | User's Guide - Page 33
    TRENDnet User's Guide minimum transmission delay for Voice, Video, multimedia, and mission critical applications, and rely on best-effort parameters for traditional IP All Rights Reserved. TEW-676APBO Queue AC_BK AC_BE AC_VI limit (in milliseconds) of a range from which the initial random backoff
  • TRENDnet TEW-676APBO | User's Guide - Page 34
    TRENDnet User's Guide support WDS. Access points know each other by MAC Address. In other words, each access point needs to include MAC address of its peer. Ensure all access points are configured with the same channel and own same security type settings. TEW-676APBO can be reviewed via this
  • TRENDnet TEW-676APBO | User's Guide - Page 35
    Date : The build time of the firmware installed.  Device Time : The current time of the system.  System Up Time : The time period that system has been in service since last reboot.  Network Information : Display the information of the Network. TEW-676APBO  Receive packets : The total received
  • TRENDnet TEW-676APBO | User's Guide - Page 36
    TRENDnet User's Guide  MAC Address : Display MAC address of WDS peer.  Signal TEW-676APBO could be used as a L2 or L3 device. It doesn't support dynamic routing protocols such as RIP or OSPF. Static routes to specific hosts, networks or default gateway are set up automatically according to the IP
  • TRENDnet TEW-676APBO | User's Guide - Page 37
    TRENDnet User's Guide  Bridge STP Information : Select "Bridge STP Information" on the drop-down list to display a list of bridge STP information. TEW-676APBO  Time : The date very useful as a troubleshooting tool when issues are experienced in system. © Copyright 2012TRENDnet. All Rights Reserved
  • TRENDnet TEW-676APBO | User's Guide - Page 38
    TRENDnet User's Guide CPE Mode IP Filter Firmware Upgrade Station Statistics LAN Site Survey MAC Filter Network Utility Extra Info Functions DDNS Virtual Server Reboot QoS Plot Management Parental Control Event Log Time Server QoS UPNP SNMP CPE Mode Functions TEW-676APBO
  • TRENDnet TEW-676APBO | User's Guide - Page 39
    TRENDnet User's Guide Configure WAN Setup There are three connection types for the WAN port : Static IP, Dynamic IP, PPPoE and PPTP. Please click on System -> WAN and follow the below setting. TEW-676APBO  Dynamic IP : Please consult with WISP for correct wireless settings to associate with WISP
  • TRENDnet TEW-676APBO | User's Guide - Page 40
    TRENDnet User's Guide  PPTP : The Point-to-Point Tunneling Protocol (PPTP) mode enables the implementation of secure multi-protocol Virtual Private Networks (VPNs) through public networks. TEW-676APBO  DNS : Check "No Default DNS Server" or "Specify DNS Server IP schemes are supported. MPPE
  • TRENDnet TEW-676APBO | User's Guide - Page 41
    TRENDnet User's Guide Configure DDNS Setup Dynamic DNS allows you to map domain name to dynamic IP address. Please click on System -> DDNS Setup and follow the below setting. TEW-676APBO Configure LAN Setup Here are the instructions for how to setup the local IP Address and Netmask. Please click on
  • TRENDnet TEW-676APBO | User's Guide - Page 42
    . Select "Manual" to set "MPDU Density"  MPDU Density : Minimum separation of MPDUs in an A-MPDU. 0 1 2 3456 7 No Restriction ¼ µs ½ µs 1 µs 2 µs 4 µs 8 µs 16 µs  A-MSDU : Aggregated Mac Service Data Unit, A-MSDU. Select Enable to allows aggregation for multiple MSDUs in one MPDU. Default is
  • TRENDnet TEW-676APBO | User's Guide - Page 43
    TRENDnet User's Guide range of 1~2347 byte. The default default, RTS is disabled in a normal environment supports non-jumbo frames.  Short Preamble : By default, it's "Auto". To Disable is to use Long 128-bit Preamble © Copyright 2012TRENDnet. All Rights Reserved. TEW-676APBO Extend Service Set ID
  • TRENDnet TEW-676APBO | User's Guide - Page 44
    TRENDnet User's Guide Create Wireless Profile The administrator can configure station profiles via this page. Please click on Wireless -> Wireless Profile and follow the below setting. TEW-676APBO Enter HEX or ASCII format WEP key value; the system supports up to 4 sets of WEP keys. Key Length Hex
  • TRENDnet TEW-676APBO | User's Guide - Page 45
    TRENDnet User's Guide  Profile List : The user can manage the created profiles for home, work or public areas. Below depict an example for Profile List TEW-676APBO  Click "Edit" an exist profile on the Profile List. The field of System Configuration and Security Policy will display profile's
  • TRENDnet TEW-676APBO | User's Guide - Page 46
    number of MAC addresses. Important to note that MAC filter rules have precedence over IP Filter rules. Please click on Advance -> MAC Filter Setup and follow the below setting. TEW-676APBO  MAC Filter Rule : By default, it's "Disable". Options are Disabled, Only Deny List MAC or Only Allow List
  • TRENDnet TEW-676APBO | User's Guide - Page 47
    TRENDnet User's Guide Parental Control Setup Parental Control allows you to block or allow specific kinds of Internet usage and traffic, such as Internet access, designated services, and websites. TEW-676APBO Main WIFI WAN LAN Please click on Advance -> Parental Control and follow the below
  • TRENDnet TEW-676APBO | User's Guide - Page 48
    TRENDnet User's Guide Click "Remove" button can remove URL or keywords. TEW-676APBO QoS Setup Quality of Service (QoS) refers to both a network's ability to Specify local port(LAN port) range required for this rule  Destination Port : Specify destination port range required for this rule  Active
  • TRENDnet TEW-676APBO | User's Guide - Page 49
    TRENDnet User's Guide for identifying purposes. © Copyright 2012TRENDnet. All Rights Reserved. TEW-676APBO  MAC Address : Enter MAC address in valid MAC Services Code Point (DSCP)-into the 8-bit Differentiated Services (DS) field of the IP packet header. Below depicts class for DSCP.  BE : Default
  • TRENDnet TEW-676APBO | User's Guide - Page 50
    than rule 2 TEW-676APBO Resource Sharing DMZ DMZ is commonly work with the NAT functionality as an alternative of Virtual Server(Port Forwarding) while wanting all ports of DMZ host visible to Internet users. Virtual Server rules have precedence over the DMZ rule. In order to use a range of ports
  • TRENDnet TEW-676APBO | User's Guide - Page 51
    TRENDnet User's Guide Virtual Server ( IP address. The NAT network appears as a single host on the Internet. A TEW-676APBO Main WIFI WAN LAN B Please click on Advance -> Virtual Server and follow the below setting. © Copyright 2012TRENDnet. All Rights Reserved.  Virtual Server : By Default
  • TRENDnet TEW-676APBO | User's Guide - Page 52
    TRENDnet User's Guide DMZ Enabled : 192.168.2.12 Rule Protocol Private IP 1 TCP 192.168.2.10 2 TCP 192.168.2.12 Rule Protocol Private IP 1 TCP 192.168.2.11 2 TCP 192.168.2.10 Private Port 20:80 22 Public Port 20:80 22 © Copyright 2012TRENDnet. All Rights Reserved. TEW-676APBO 52
  • TRENDnet TEW-676APBO | User's Guide - Page 53
    Server Status can be reviewed via this page.  System : Display the information of the system. TEW-676APBO  WAN Information : Display the information of the WAN interface.  System Name : The name of the system.  Operating Mode : The mode currently in service.  Location : The reminding note
  • TRENDnet TEW-676APBO | User's Guide - Page 54
    TRENDnet User's Guide  LAN Information : Display total received and transmitted statistics on the LAN interface. TEW-676APBO  IP Address : IP addresses to LAN devices by DHCP server.  MAC Address : MAC addresses of LAN devices.  Expired In : Shows how long the leased IP address will expire.
  • TRENDnet TEW-676APBO | User's Guide - Page 55
    TRENDnet User's Guide  Link Status :  Status : Shows the current link status. It should be number of unsuccessful received CTS © Copyright 2012TRENDnet. All Rights Reserved. TEW-676APBO response after this TEW-676APBO sends out the RTS message.  Receive Statistics  Frames Received Successfully
  • TRENDnet TEW-676APBO | User's Guide - Page 56
    -down list to display route table. TEW-676APBO could be used as a L2 or L3 device. It doesn't support dynamic routing protocols such as RIP or OSPF. Static routes to specific hosts, networks or default gateway are set up automatically according to the IP configuration of system's interfaces. When
  • TRENDnet TEW-676APBO | User's Guide - Page 57
    TRENDnet User's Guide QoS Plot 5 seconds. The throughput statistics of QoS can be updated manually using the Refresh button. TEW-676APBO  Time : The date and time when the event very useful as a troubleshooting tool when issues are experienced in system. © Copyright 2012TRENDnet. All Rights Reserved
  • TRENDnet TEW-676APBO | User's Guide - Page 58
    TRENDnet User's Guide TEW-676APBO Wireless Profile IP Filter MAC Filter Virtual Server Firmware Upgrade service to residents and business customers. In the CPE+AP mode, TEW676APBO is a gateway enabled with NAT and DHCP Server functions. The wired and wireless clients connected to TEW-676APBO
  • TRENDnet TEW-676APBO | User's Guide - Page 59
    the below setting. TEW-676APBO release IP address and click Renew button to renew IP address again.  Hostname : The Hostname of the WAN port  Mode : By default, it's "Static IP". Check "Static IP", "Dynamic IP", "PPPoE" or "PPTP"to set up system WAN IP.  Static IP : Users can manually setup the
  • TRENDnet TEW-676APBO | User's Guide - Page 60
    TRENDnet User's Guide TEW-676APBO  Secondary : The IP address of the secondary DNS server. Click Save button to save your changes. Click Reboot button to activate your changes Configure DDNS Setup Dynamic DNS allows you to map domain name to dynamic IP address. Please click on System -> DDNS Setup
  • TRENDnet TEW-676APBO | User's Guide - Page 61
    TRENDnet User's Guide Configure LAN Setup Here are the instructions for how to setup the local IP Address and Netmask. Please click on System -> LAN and follow the below setting. TEW-676APBO  LAN IP : The administrator can manually setup the LAN IP address.  IP Address : The IP address of the
  • TRENDnet TEW-676APBO | User's Guide - Page 62
    100 (the unit is %) for your environment. If you are not sure of which setting to choose, then keep the default setting, 100%. © Copyright 2012TRENDnet. All Rights Reserved. TEW-676APBO When Band Mode select in 802.11a only mode, the HT(High Throughput) Physical Mode and 11n Configuration settings
  • TRENDnet TEW-676APBO | User's Guide - Page 63
    TRENDnet User's Guide Wireless Advanced Setup To achieve optimal wireless performance, it is Rights Reserved. TEW-676APBO  Extra Slot Time : Slot time is in the range of 1~255 and set in unit of microsecond. The default value is 9 microsecond.  ACK Timeout : ACK timeout is in the range of 1~255
  • TRENDnet TEW-676APBO | User's Guide - Page 64
    TRENDnet User's Guide range of 1~2347 byte. The default Most traditional IP data is default, RTS is disabled in a normal environment supports non-jumbo frames.  Short Preamble : By default, it's "Enable". To Disable is to use Long 128-bit © Copyright 2012TRENDnet. All Rights Reserved. TEW-676APBO
  • TRENDnet TEW-676APBO | User's Guide - Page 65
    TRENDnet User's Guide the requirements of the media being sent. Queues automatically provide minimum transmission delay for Voice, Video, multimedia, and mission critical applications, and rely on best-effort parameters for traditional IP milliseconds) of a range from which the initial TEW-676APBO
  • TRENDnet TEW-676APBO | User's Guide - Page 66
    TRENDnet User's Guide advanced settings and will be applied to Repeater AP. Site Survey Use this tool to scan and locate WISP Access Points and select one to associate with. Please click on Wireless -> Site Survey. Below depicts an example for site survey. TEW-676APBO Service channel range. 
  • TRENDnet TEW-676APBO | User's Guide - Page 67
    TRENDnet User's Guide TEW-676APBO Key Length 64-bit 128-bit Hex 10 characters 26 characters ASCII 5 time, but only one is chosen.  WEP Key # : Enter HEX or ASCII format WEP key value; the system supports up to 4 sets of WEP keys.  WPA-PSK (or WPA2-PSK) : WPA (or WPA2) Algorithms, allows the
  • TRENDnet TEW-676APBO | User's Guide - Page 68
    TRENDnet User's Guide TEW-676APBO archived and setting of AP's clients could make to associate to it.  Maximum Clients : The default will determine the service type available to AP's clients associated with the specified AP.  Client Isolation : By default, it's supports up to 4 sets of WEP keys. 68
  • TRENDnet TEW-676APBO | User's Guide - Page 69
    server. • Shared secret : A secret key used between system and RADIUS server. Supports 8 to 64 characters. • Session Timeout : The Session timeout is in the range of 0~60 seconds. The default is 0 to disable re-authenticate service. Amount of time before a client will be required to re-authenticate
  • TRENDnet TEW-676APBO | User's Guide - Page 70
    TRENDnet User's Guide • Shared secret : A secret key used between system and RADIUS server. Supports 8 to 64 characters. • Session Timeout : The Session timeout is in the range of 0~60 seconds. The default is 0 to disable re-authenticate service Repeater AP. TEW-676APBO  Add a IP Filter Setup Allows
  • TRENDnet TEW-676APBO | User's Guide - Page 71
    TRENDnet User's Guide  Source Address/Mask : Enter desired source IP address and netmask; i.e. 192.168.2.10/32.  Source Port : Enter a port or a range of ports as start:end; i.e. port 20:80  Destination Address/Mask : Enter desired destination IP address and netmask; i.e. 192.168.1.10/32 
  • TRENDnet TEW-676APBO | User's Guide - Page 72
    TRENDnet User's Guide designated services, and websites. N TEW-676APBO Main IP : Specify local(LAN)/ destination IP addresses range required for this rule. If you specify local IP addresses range from 192.168.1.1 to 192.168.2.254. The matches a range of local IP addresses include every single IP
  • TRENDnet TEW-676APBO | User's Guide - Page 73
    TRENDnet User's Guide Click "Remove" button can remove URL or keywords. TEW-676APBO QoS Setup Quality of Service (QoS) refers to both a network's ability to Specify local port(LAN port) range required for this rule  Destination Port : Specify destination port range required for this rule  Active
  • TRENDnet TEW-676APBO | User's Guide - Page 74
    TRENDnet User's Guide : N Main WIFI WAN LAN Down: 1024Kbps B p: 12Kbps Down: 2048Kbps Up:1024Kbp A Please click on Advance -> QoS and follow the below setting. TEW-676APBO  Rules : Use the rules to define the classifiers. After you define the rules, you can specify action to act upon the
  • TRENDnet TEW-676APBO | User's Guide - Page 75
    TRENDnet User's Guide Rule Source IP Destination IP between 8 to 8192, default upload is 128 Kbps, IP address and other remaining protocol of IP address 192.168.2.10 only can use total bandwidth 512 Kbps © Copyright 2012TRENDnet. All Rights Reserved. TEW-676APBO to use a range of ports available
  • TRENDnet TEW-676APBO | User's Guide - Page 76
    TRENDnet User's Guide TEW-676APBO Please click on Advance -> Virtual Server and follow the below setting.  DMZ : By default, it's "Disable". Check Enable radial button to enable DMZ.  IP Address : Enter IP address of DMZ host and only one DMZ host is supported. Click Save button to save your
  • TRENDnet TEW-676APBO | User's Guide - Page 77
    11. The rule 2 won't take effect. DMZ Enabled : 192.168.2.12 Rule Protocol Private IP 1 TCP 192.168.2.11 2 TCP 192.168.2.10 Private Port 20:80 22 Public Port 20:80 22 TEW-676APBO System Status This section breaks down into subsections of System Overview, Associated Clients Status, Remote
  • TRENDnet TEW-676APBO | User's Guide - Page 78
    TRENDnet User's Guide TEW-676APBO  LAN Information : Display total received and transmitted statistics on the LAN interface. The WAN port specified Dynamic IP, the Release and Renew button will be showup, click Release button to release IP address of WAN port, Renew button to renew IP address
  • TRENDnet TEW-676APBO | User's Guide - Page 79
    TRENDnet User's Guide  Station Rate retrieve DHCP server and DHCP clients' IP/MAC address via this field. TEW-676APBO Associated Clients Status It displays ESSID, wireless connection.  Disconnect : Click "Delete" button to manually disconnect a wireless client in a Repeater AP. © Copyright
  • TRENDnet TEW-676APBO | User's Guide - Page 80
    TRENDnet User's Guide Remote AP SSID, MAC address, antenna 0/1 received signal strength and channel bandwidth for associated AP are available. TEW-676APBO Extra Info Users could pull out information such as Route table, ARP table, MAC table, Bridge table or STP available in the drop-down list
  • TRENDnet TEW-676APBO | User's Guide - Page 81
    TRENDnet User's Guide Protocol, Live Time, Status , Source/Destination IP address and Port.  Route table information : Select "Route table information" on the drop-down list to display route table. TEW-676APBO could be used as a L2 or L3 device. It doesn't support dynamic routing protocols such as
  • TRENDnet TEW-676APBO | User's Guide - Page 82
    TRENDnet User's Guide manually using the Refresh button. Event Log The Event log displays system events when system is up and running. Also, it becomes very useful as a troubleshooting tool when issues are experienced in system. TEW-676APBO Utilities Profiles Settings Firmware Upgrade Network Utility
  • TRENDnet TEW-676APBO | User's Guide - Page 83
    subnet from Main Base Station and it accepts wireless connections from wireless client devices. SSID: Repeater_Main_AP TEW-676APBO Configure LAN IP Here are the instructions for how to setup the local IP Address and Netmask. Please click on System -> LAN and follow the below setting. Main Client
  • TRENDnet TEW-676APBO | User's Guide - Page 84
    TRENDnet User's Guide  IP Gateway : The default gateway of the LAN port; default Gateway is 192.168.2.1  Dynamic IP : This configuration type is applicable when the TEW-676APBO is connected to a network with the presence of a DHCP server; all related IP information will be provided by the DHCP
  • TRENDnet TEW-676APBO | User's Guide - Page 85
    3456 7 No Restriction ¼ µs ½ µs 1 µs 2 µs 4 µs 8 µs 16 µs © Copyright 2012TRENDnet. All Rights Reserved. TEW-676APBO  A-MSDU : Aggregated Mac Service Data Unit, A-MSDU. Select Enable to allow aggregation for multiple MSDUs in one MPDU. Default is disabled. Click Save button to save your changes
  • TRENDnet TEW-676APBO | User's Guide - Page 86
    TRENDnet User's Guide ownership and finish their transmission and release the channel. TEW-676APBO  DTIM Interval : The DTIM interval is in the range of 1~255. The default is 1. DTIM is defined as Delivery Traffic Indication Message. It is used to notify the wireless stations, which support power
  • TRENDnet TEW-676APBO | User's Guide - Page 87
    TRENDnet User's Guide with other APs in channel.  Pkt_Aggregate : By default IP data default, it's "Disable". To Enable is to use WMM and the WMM parameters should appears. © Copyright 2012TRENDnet. All Rights Reserved. TEW-676APBO range from which the initial random backoff wait time is
  • TRENDnet TEW-676APBO | User's Guide - Page 88
    TRENDnet User's Guide this policy is © Copyright 2012TRENDnet. All Rights Reserved. TEW-676APBO used, a sender does not retransmit packets that have not the Minimum Contention Window is the upper limit (in milliseconds) of a range from which the initial random back off wait time is determined. 
  • TRENDnet TEW-676APBO | User's Guide - Page 89
    TRENDnet User's Guide Site Survey Use this tool to scan and locate WISP Access Points and select one to associate with. Please click on Wireless -> Site Survey. Below depicts an example for site survey. TEW-676APBO ESSID : Assign Service Set ID for Select the desired channel range.  Security Type :
  • TRENDnet TEW-676APBO | User's Guide - Page 90
    TRENDnet User's Guide  WEP Key # : Enter HEX or ASCII format WEP key value; the system supports up to 4 sets of WEP keys.  WPA-PSK (or WPA2-PSK) : or public areas. Below depict an example for Profile List TEW-676APBO Configuration and Security Policy will display profile's content. Edit profile
  • TRENDnet TEW-676APBO | User's Guide - Page 91
    TRENDnet User's Guide  Enable Repeater AP : By default, it's "Enable" for repeater AP. Select "Enable" to activate Repeater AP or click "Disable" to deactivate this function  ESSID : Extended Service shared key. TEW-676APBO  Authentication Method key value; the system supports up to 4 sets of
  • TRENDnet TEW-676APBO | User's Guide - Page 92
    TRENDnet User's Guide TEW-676APBO following Dynamic WEP and RADIUS settings to complete configuration.  WPA General Settings : • Cipher Suite : By default, it is AES. Select either AES or TKIP cipher suites • Group Key Update Period : By default, it's 3600 seconds. This time interval for rekeying
  • TRENDnet TEW-676APBO | User's Guide - Page 93
    TRENDnet User's Guide Wireless MAC Filter Setup Continue 7.3.1 Repeater AP Setup section, the administrator can allow or reject clients to access Repeater AP. TEW-676APBO System Status This section breaks down into subsections of System Overview, Associated Clients Status, Remote AP, Extra
  • TRENDnet TEW-676APBO | User's Guide - Page 94
    TRENDnet User's Guide  Network Information : Display the information of the Network. TEW-676APBO  Mode : Supports Static or Dynamic modes on the LAN interface.  IP Address : The management IP of system. By default, it's 192.168.2.254.  IP Netmask : The network mask. By default, it's 255.255.
  • TRENDnet TEW-676APBO | User's Guide - Page 95
    TRENDnet User's Guide Associated Clients Status It displays ESSID, on/off Status, Security Type, total number of wireless clients associated with Repeater AP. TEW-676APBO Delete" button to manually disconnect a wireless TEW-676APBO could be used as a L2 or L3 device. It doesn't support dynamic 95
  • TRENDnet TEW-676APBO | User's Guide - Page 96
    specific hosts, networks or default gateway are set up automatically according to the IP configuration of system's interfaces. When used as a L2 device, it could switch packets and, as L3 device, it's capable of being a gateway to route packets inward and outward. TEW-676APBO Ageing timers will be
  • TRENDnet TEW-676APBO | User's Guide - Page 97
    TRENDnet User's Guide © Copyright 2012TRENDnet. All Rights Reserved. TEW-676APBO Event Log The Event log displays system events when system is up and running. Also, it becomes very useful as a troubleshooting tool when issues are experienced in system.  Time : The date and time when the event
  • TRENDnet TEW-676APBO | User's Guide - Page 98
    TRENDnet User's Guide Router Mode Wireless General Setup Advance DMZ WAN Advanced Setup IP Filter Functions LAN DDNS Virtual AP Setup MAC Filter Firmware Upgrade Network l Reboot Status System Overview Station Statistics Extra Info QoS Plot Event Log Router AP Mode Functions TEW-676APBO
  • TRENDnet TEW-676APBO | User's Guide - Page 99
    TRENDnet User's Guide Configure WAN Setup There are three connection types for the WAN port : Static IP, Dynamic IP, PPPoE and PPTP. Please click on System -> WAN and follow the below setting. TEW-676APBO  IP Netmask : The Subnet mask of the WAN port; default Netmask is 255.255.255.0  IP Gateway
  • TRENDnet TEW-676APBO | User's Guide - Page 100
    TRENDnet User's Guide  PPTP : The Point-to-Point Tunneling Protocol (PPTP) mode enables the implementation of secure multi-protocol Virtual Private Networks (VPNs) through public networks. TEW-676APBO  DNS : Check "No Default DNS Server" or "Specify DNS Server IP schemes are supported. MPPE
  • TRENDnet TEW-676APBO | User's Guide - Page 101
    TRENDnet User's Guide Configure DDNS Setup Dynamic DNS allows you to map domain name to dynamic IP address. Please click on System -> DDNS Setup and follow the below setting. TEW-676APBO Configure LAN Setup Here are the instructions for how to setup the local IP Address and Netmask. Please click on
  • TRENDnet TEW-676APBO | User's Guide - Page 102
    TRENDnet User's Guide TEW-676APBO Wireless LAN Network Creation The network manager can configure Disable to deactivate this service.  Start IP / End IP: Specify the range of IP addresses to be used by the DHCP server when assigning IP address to clients. The default range IP address is 192.168.2.
  • TRENDnet TEW-676APBO | User's Guide - Page 103
    TRENDnet User's Guide desired rate from the drop-down list; the options are auto or ranging from 6 to 54Mbps only for 802.11a mode.  Tx Default is disabled. Change these settings as described here and click Save button to save your changes. © Copyright 2012TRENDnet. All Rights Reserved. TEW-676APBO
  • TRENDnet TEW-676APBO | User's Guide - Page 104
     DTIM Interval : The DTIM interval is in the range of 1~255. The default is 1. © Copyright 2012TRENDnet. All Rights Reserved. TEW-676APBO DTIM is defined as Delivery Traffic Indication Message. It is used to notify the wireless stations, which support power saving mode, when to wake up to receive
  • TRENDnet TEW-676APBO | User's Guide - Page 105
    TRENDnet User's Guide  Pkt_Aggregate : By default . Medium Most traditional IP data is sent to default, it's "Disable". To Enable is to use WMM and the WMM parameters should appears. © Copyright 2012TRENDnet. All Rights Reserved. TEW-676APBO in milliseconds) of a range from which the initial random
  • TRENDnet TEW-676APBO | User's Guide - Page 106
    TRENDnet User's Guide 2012TRENDnet. All Rights Reserved. TEW-676APBO Queue AC_BK AC_BE AC_VI AC_VO Data data is sent to this queue Most traditional IP Video High Minimum delay. Time-sensitive video the upper limit (in milliseconds) of a range from which the initial random backoff wait time
  • TRENDnet TEW-676APBO | User's Guide - Page 107
    TRENDnet User's Guide TEW-676APBO Click Save button to save your changes. Click Reboot button to activate your changes. The items in this page are for AP's RF advanced settings and will be applied to all VAPs and WDS Links. Create Virtual AP (VAP) The TEW-676APBO support broadcasting multiple
  • TRENDnet TEW-676APBO | User's Guide - Page 108
    AP setup page appears. TEW-676APBO VAP0 VAP1 VAP2 Cllent Isolation AP Isolation  Enable AP : By default, it's "Disable" for VAP1 ~ VAP6. The Primary AP always enabled. Select "Enable" to activate VAP or click "Disable" to deactivate this function  ESSID : Extended Service Set ID, When clients
  • TRENDnet TEW-676APBO | User's Guide - Page 109
    TRENDnet User's Guide 128-bit shared key. TEW-676APBO  Cipher Suite : By default, it is AES. Select format WEP key value; the system supports up to 4 sets of WEP keys default, it is AES. Select either PMK Cache Period : By default, it's 10 minutes. Pre-Authentication : By default, it's "Disable".
  • TRENDnet TEW-676APBO | User's Guide - Page 110
    TRENDnet User's Guide server. • Port : By default, it's 1812. The port number used to communicate with RADIUS server. • Shared secret : A secret key used between system and RADIUS server. Supports 8 to 64 characters. • Session Timeout : The Session timeout is in the range of 0~60 seconds. The
  • TRENDnet TEW-676APBO | User's Guide - Page 111
    TRENDnet User's Guide Wireless Network Expansion The support WDS. Access points know each other by MAC Address. In other words, each access point needs to include MAC address of its peer. Ensure all access points are configured with the same channel and own same security type settings. TEW-676APBO
  • TRENDnet TEW-676APBO | User's Guide - Page 112
    or multicast packets on different protocols as shown in the IP Filter Setup. Important to note that IP filter rules has precedence over Virtual server rules. Please click on Advance -> IP Filter Setup and follow the below setting. TEW-676APBO  Listen : Click Yes radial button to match TCP packets
  • TRENDnet TEW-676APBO | User's Guide - Page 113
    and follow the below setting. TEW-676APBO Parental Control Setup Parental Control allows you to block or allow specific kinds of Internet usage and traffic, such as Internet access, designated services, and websites. Station  MAC Filter Rule : By default, it's "Disable". Options are Disabled
  • TRENDnet TEW-676APBO | User's Guide - Page 114
    TRENDnet User's Guide TEW-676APBO Application) from drop-down list. When you IP : Specify local(LAN)/ destination IP addresses range required for this rule. If you specify local IP addresses range from 192.168.1.1 to 192.168.2.254. The matches a range of local IP addresses include every single IP
  • TRENDnet TEW-676APBO | User's Guide - Page 115
    TRENDnet User's Guide QoS Setup Quality of Service (QoS) refers to both a network's ability to deliver Advance -> QoS and follow the below setting. © Copyright 2012TRENDnet. All Rights Reserved. TEW-676APBO Remote Bass Station WDS Down: 1024Kbps Up: 512Kbps SSID: Main_AP WAN WLAN NAT Down:
  • TRENDnet TEW-676APBO | User's Guide - Page 116
    TRENDnet User's Guide the MAC group of © Copyright 2012TRENDnet. All Rights Reserved. TEW-676APBO each rule. Click "Remove" button can remove MAC address Services Code Point (DSCP)-into the 8-bit Differentiated Services (DS) field of the IP packet header. Below depicts class for DSCP.  BE : Default
  • TRENDnet TEW-676APBO | User's Guide - Page 117
    TRENDnet User's Guide a number between 8 to 8192, default upload is 128 Kbps, download is 1024 Kbps. Click Reserved. TEW-676APBO  DMZ : By default, it's "Disable". Check Enable radial button to enable DMZ.  IP Address : Enter IP address of DMZ host and only one DMZ host is supported. Click Save
  • TRENDnet TEW-676APBO | User's Guide - Page 118
    TRENDnet User's Guide Please click on Advance -> Virtual Server and follow the below setting. TEW-676APBO remaining connections to port TCP 20~80 will be redirected to port TCP 20~80 of 192.168.2.11  Example 2 : All connections should be redirected
  • TRENDnet TEW-676APBO | User's Guide - Page 119
    TRENDnet User's Guide  WAN Information : Display the information of the WAN interface. TEW-676APBO  MAC Address : The MAC address of the WAN port.  IP Address : The IP address of the WAN port.  IP Netmask : The IP netmask of the WAN port.  IP Gateway : The gateway IP address of the WAN port. 
  • TRENDnet TEW-676APBO | User's Guide - Page 120
    TRENDnet User's Guide TEW-676APBO Associated Clients : Users could retrieve DHCP server and DHCP clients' IP/MAC address via this field.  IP Address : IP addresses to LAN devices by DHCP server.  MAC Disconnect : Click "Delete" button to manually disconnect a wireless client in a Virtual AP. 120
  • TRENDnet TEW-676APBO | User's Guide - Page 121
    TRENDnet User's Guide Show WDS Link Peers MAC Address, antenna 0/1 received signal strength, phy mode and channel bandwidth for each WDS are available. TEW-676APBO Extra Info Users could pull out information such as Route table, ARP table, MAC table, Bridge table or STP available in the drop-down
  • TRENDnet TEW-676APBO | User's Guide - Page 122
    TRENDnet User's Guide  Netstat Information : Select "NetStatus Information" on TEW-676APBO could be used as a L2 or L3 device. It doesn't support dynamic routing protocols such as RIP or OSPF. Static routes to specific hosts, networks or default gateway are set up automatically according to the IP
  • TRENDnet TEW-676APBO | User's Guide - Page 123
    TRENDnet User's Guide manually using the Refresh button. TEW-676APBO System Management Configure Management Administrator could specify geographical location of the system via instructions running. Also, it becomes very useful as a troubleshooting tool when issues are experienced in system.  Time
  • TRENDnet TEW-676APBO | User's Guide - Page 124
    Enable SSH : Check to select SSH Service  SSH Port : Please The default is 22 and the range is between 1 ~ 65535.  Ping Watchdog : The ping watchdog sets the TEW-676APBO Device to continuously © Copyright 2012TRENDnet. All Rights Reserved. TEW-676APBO ping a user defined IP address (it can be the
  • TRENDnet TEW-676APBO | User's Guide - Page 125
    TRENDnet User's Guide TEW-676APBO Configure System Time System time can be configured via this page, and manual setting or via a NTP server is supported system time with NTP server.  Enable : Check to select NTP client.  Default NTP Server : Select the NTP Server from the drop-down list.  Time
  • TRENDnet TEW-676APBO | User's Guide - Page 126
    in Windows XP, the "TEW-676APBO" must be available in "My Network Places", as shown here: (your specific model may vary)  SNMP v2c Enable: Check to enable SNMP v2c. TEW-675APBO/TEW676APBO If these devices are not available, you should verify that the correct components and services are loaded in
  • TRENDnet TEW-676APBO | User's Guide - Page 127
    TRENDnet User's Guide  SNMP ro user TEW-676APBO Backup / Restore and Reset to Factory Backup current configuration, restore prior configuration or reset back to factory default trap messages or notices send by the system.  IP : Enter the IP addresses of the remote hosts to receive trap messages.
  • TRENDnet TEW-676APBO | User's Guide - Page 128
    or bugs fix. It takes around 2 minutes to upgrade due to complexity of firmware. To upgrade system firmware, click Browse button to locate the new firmware, and then click Upgrade button to upgrade. TEW-676APBO Network Utility The administrator can diagnose network connectivity via the PING and
  • TRENDnet TEW-676APBO | User's Guide - Page 129
    TRENDnet User's Guide  Count : By default, it's 5 and the range is from 1 to 50. It indicates number of connectivity test.  Traceroute : Allows tracing the hops from the TEW-676APBO device to a selected outgoing IP address. It should be used for the finding the route taken by ICMP packets across
  • TRENDnet TEW-676APBO | User's Guide - Page 130
    TRENDnet User's Guide Appendix WEB GUI Valid Characters Block LAN Field IP Address IP Netmask IP Gateway Primary DNS Secondary DNS Hostname WAN Manual MAC Address IP Address IP Netmask IP Gateway © Copyright 2012TRENDnet. All Rights Reserved. Valid Characters IP Format; 1-254 128.0.0.0 ~ 255.
  • TRENDnet TEW-676APBO | User's Guide - Page 131
    TRENDnet User's Guide Hostname DDNS User name Password MTU Idle Time Primary DNS Secondary DNS Hostname User Name Password © Copyright 2012TRENDnet. All Rights Reserved. Length : 32 0-9, A-Z, a-z Length : 32 0-9, A-Z, a-z 576 ~ 1492 for PPPoE; 1400 ~ 1460 for PPTP 0 ~ 60 minutes IP Format;
  • TRENDnet TEW-676APBO | User's Guide - Page 132
    TRENDnet User's Guide DHCP Server Start IP End IP DNS1 IP DNS2 IP WINS IP Domain Block Management Lease Time Field System Name/ Location Description © Copyright 2012TRENDnet. All Rights Reserved. IP Format; 1-254 IP Format; 1-254 IP Format; 1-254 IP Format; 1-254 IP Format; 1-254 Length : 32
  • TRENDnet TEW-676APBO | User's Guide - Page 133
    TRENDnet User's Guide Password SNMP HTTP/ HTTPS Port Telnet/ SSH Port RO/RW community RO/RW user RO/RW password Community © Copyright 2012TRENDnet. All Rights Reserved. Length : 4 ~ 30 0-9, A-Z, a-z 1 ~
  • TRENDnet TEW-676APBO | User's Guide - Page 134
    TRENDnet User's Guide General Setup Wireless Profile IP Tx Power Profile Name ESSID Advanced Setup Block WEP Key Pre-shared Key Beacon Interval Date Beacon Rate Fragment Threshold RTS Threshold Field © Copyright 2012TRENDnet. All Rights Reserved. IP Format; 1-254 1-100 % 32 chars Length : 31
  • TRENDnet TEW-676APBO | User's Guide - Page 135
    TRENDnet User's Guide Virtual AP Setup ESSID WDS Setup Maximum Clients VLAN ID WEP Key Group Key Update Period PMK Cache Period Pre-Shared Key Radius Server IP Radius Port Shared Secret Session Timeout WEP Key © Copyright 2012TRENDnet. All Rights Reserved. Length : 31 Space 0-9, A-Z, a-z 1 ~
  • TRENDnet TEW-676APBO | User's Guide - Page 136
    TRENDnet User's Guide IP Filter MAC Filter Virtual Server DMZ QoS/ TKIP Key AES Key Peer's MAC Address Description Source Address Source Mask Source Port Destination Address Destination Mask Destination Port MAC address Description Private IP Private/ Public Port IP Address Comment © Copyright
  • TRENDnet TEW-676APBO | User's Guide - Page 137
    TRENDnet User's Guide Parental Control MAC Address Local/ Destination IP Local/ Destination Port Upload & Download MAC Format; 12 HEX chars IP Format; 1-254 1 ~ 65535 8 ~ 8192 digital number Appendix © Copyright 2012TRENDnet. All Rights Reserved. 137
  • TRENDnet TEW-676APBO | User's Guide - Page 138
    TRENDnet User's Guide Appendix MCS Data Rate The table below shows the relationships between the variables that allow for the maximum data rate Note :  When MCS=32, only Short Guard Interval option is supported, Channel Bandwidth=20 is not supported. If Channel Bandwidth=40, the HT duplicate
  • TRENDnet TEW-676APBO | User's Guide - Page 139
    TRENDnet User's Guide System LAN DDNS Time Server UPNP SNMP General Advanced Site Survey DMZ IP Filter MAC Filter Virtual Server Parental l © Copyright 2012TRENDnet. System Network l Reboot Backup Settings Restore Reset fl TEW-676APBO Read Read Read Read & Write Read Read Read & Write Read
  • TRENDnet TEW-676APBO | User's Guide - Page 140
    TRENDnet User's Guide Windows TCP/IP Settings  Windows XP 1. Click Start -> Settings -> Control Panel, and then "Control Panel" window appears. Click on "Network Connections", and then "Network Connections" window appears. TEW-676APBO 3. In "Local Area Connection Properties" window, select "
  • TRENDnet TEW-676APBO | User's Guide - Page 141
    TRENDnet User's Guide TEW-676APBO Enabling UPnP in Windows XP 1. Open the "Add/Remove Programs" control panel, and then click on "Add/Remove Windows Components" in the sidebar. Scroll down and find "Networking Services", highlight it, and then click Details. 2. In the "Networking Services" window
  • TRENDnet TEW-676APBO | User's Guide - Page 142
    TRENDnet User's Guide TEW-676APBO 3. Next, in the "Control panel", open the "Administrative Tools" and then open "Services". Scroll down until you find the "SSDP Discovery Interface". If the Status is not Started, double-click on SSDP Discovery Interface to open the service properties. Change the
  • TRENDnet TEW-676APBO | User's Guide - Page 143
    , WPA/WPA2RADIUS for AP/CPE mode, WEP/WPA2-PSK for WDS mode MAC filter (20 entries) and IP filter (20 entries) Up to 26dBm (FCC) 802.11a: -91dBm (typical) @ 6Mpbs © Copyright 2012TRENDnet. All Rights Reserved. Channels TEW-676APBO 802.11a/n: -68dBm (typical) @ 300Mbps FCC: 149,153,157,161,165 143
  • TRENDnet TEW-676APBO | User's Guide - Page 144
    TRENDnet User's Guide Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase. TEW-676APBO - 3 Years Warranty AC/DC Power Adapter, Cooling Fan, and Power Supply carry 1 year
  • TRENDnet TEW-676APBO | User's Guide - Page 145
    to the copyrights of the developers. TRENDnet does not provide technical support for these codes. Please go to http://www.gnu.org/licenses/gpl.txt or http://www.gnu.org/licenses/lgpl.txt for specific terms of each license. PWP05202009v2 TEW-676APBO © Copyright 2012TRENDnet. All Rights Reserved
  • TRENDnet TEW-676APBO | User's Guide - Page 146
    Appendix © Copyright 2012TRENDnet. All Rights Reserved. 146
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
TRENDnet User’s Guide
Table of Contents