TRENDnet TU-ET100plus Manual
TRENDnet TU-ET100plus Manual
 |
View all TRENDnet TU-ET100plus manuals
Add to My Manuals
Save this manual to your list of manuals |
TRENDnet TU-ET100plus manual content summary:
- TRENDnet TU-ET100plus | Manual - Page 1
USB 10/100M FAST ETHERNET Quick Installation Guide M73-APO08-430 - TRENDnet TU-ET100plus | Manual - Page 2
installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation - TRENDnet TU-ET100plus | Manual - Page 3
standard ?? IEEE 802.3 for 10BaseT ?? IEEE 802.3u for 100BaseTX Data Rate ?? 10/100 Mbps1 ?? Double data transfer rate in full duplex mode Supported operating systems ?? Windows 98/2000/ME/XP Physical ?? Ports: 1 RJ-45, 1 USB A-Plug ?? LED indicators: Link/Act, 10/100 ?? Dimensions: 75.9 x 37.8 x 21 - TRENDnet TU-ET100plus | Manual - Page 4
Parts Names and Functions ? USB Connection Cable: connects the USB host port to the USB 10/100M Fast Ethernet Adapter. 1 2 3 5 4 ? USB Fast Ethernet Adapter ? 10/100 LED indicator: glows amber when 100M Network is linked; when it dims, it means the 10M Network is linked. ? Link/Act LED indicator: - TRENDnet TU-ET100plus | Manual - Page 5
. If not, either no USB port is installed or the USB bios is not properly enabled. In this case, consult your computer dealer for USB support. Getting Hooked Up 1. Locate the USB host port of your system. Align the USB connector toward the USB host port, push evenly and steadily until - TRENDnet TU-ET100plus | Manual - Page 6
2. Connect the UTP cable to the Fast Ethernet Adapter. 3. Connect the other end to a Hub. - 4 - - TRENDnet TU-ET100plus | Manual - Page 7
device is properly connected to your comp uter, Windows 98 will automatically detect the new hardware device. Perform the following procedures for installing the device driver. 2. Insert the device driver disk into your floppy drive. When the above figure appears, click Next. - 5 - - TRENDnet TU-ET100plus | Manual - Page 8
3. The installation program will proceed automatically. Follow the on-screen instruction to finish. 4. When Windows prompts you to restart your computer, click No to make some changes to your network settings. - 6 - - TRENDnet TU-ET100plus | Manual - Page 9
5. Go to Start ? Settings ? Control Panel. Double-click Network. 6. When the Network dialog box appears, select USB 10/100M Fast Ethernet and click Add. Set the appropriate protocols and client for you needs. When completed, click OK. 7. Remember to restart your computer to activate the new device - TRENDnet TU-ET100plus | Manual - Page 10
Adapter is found, it means that your device is properly installed and enabled. Installation for Windows 2000 1. Once the device is well connected to your computer, Windows 2000 will automatically detect the new device. Click Next to proceed. - 8 - - TRENDnet TU-ET100plus | Manual - Page 11
2. Select Search for a suitable driver for my device (recommended) and click Next. 3. Insert the new device driver to the disk drive. Select Floppy disk drives. Click Next. 4. Click Next. Windows will copy all the necessary files to your system. 5. Click Yes to - TRENDnet TU-ET100plus | Manual - Page 12
7. Go to Start ? Settings ? Control Panel ? Ne twork and Dial-up Connections. Double-click Local Area Connections. 8. When the Network dialog box appears, select USB 10/100 Network Adapter and click Install. Set the appropriate protocols and client for you needs. When completed, click OK. - 10 - - TRENDnet TU-ET100plus | Manual - Page 13
is well connected to your computer, Windows ME will automatically detect the new device. Select Specify the location of the driver (Advanced) and click Next. 2. Insert the device driver disk into the floppy disk drive on your system. Select Removable Media (Floppy, CD-ROM...) and click Next to - TRENDnet TU-ET100plus | Manual - Page 14
3. Click Next to continue. 4. Click Next. Windows will copy all the necessary files to your system. - 12 - - TRENDnet TU-ET100plus | Manual - Page 15
5. Click Finish to complete the software installation. 6. When asked if you want to restart your computer, click No to continue the Network configuration. 7. Go to Start ? Settings ? Control Panel. Double-click Network. 8. When the Network dialog box appears, select USB 10/100 Network Adapter and - - TRENDnet TU-ET100plus | Manual - Page 16
enabled. Installation for Windows XP 1. Once the device is well connected, Windows will detect the new device and prompt you to insert the network device driver. Click Install from a list or specific location... and click next. - 14 - - TRENDnet TU-ET100plus | Manual - Page 17
2. Insert the device Driver Disk into the floppy disk drive of your system. Select Search removable media (floppy, CDROM...) and click Next. 3. Click Next to continue. - 15 - - TRENDnet TU-ET100plus | Manual - Page 18
4. Windows will start searching for the appropriate driver for the installation. When the screen appears as below, click Continue Anyway to proceed. 5. Wait for seconds while Windows copies the appropriate driver to your system. 6. Click Finish. The software installation for this network device is - TRENDnet TU-ET100plus | Manual - Page 19
7. Go to Start ? Settings ? Control Panel ? Network and Dial-up Connections. Double-click Local Area Connections. 8. When the Network dialog box appears, select USB 10/100 Network Adapter and - 17 - - TRENDnet TU-ET100plus | Manual - Page 20
click Install. Set the appropriate protocols and client for you needs. When completed, click OK. 9. Remember to restart your computer to activate the new device. Setup Diagnostics To verify if the device exists in your computer and is enabled, go to Start ? Control Panel ? System. Click the Device
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
 |
 |
M73-APO08-430
USB
10/100M
FAST ETHERNET
Quick Installation Guide