Tanaka TCG24EBSP Owner's Manual - Page 11

from the fueling area before starting.

Get Tanaka TCG24EBSP PDF manuals and user guides View all Tanaka TCG24EBSP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

English Always start by filing half the amount of fuel, which is to be used. Then add the whole amount of oil. Mix (shake) the fuel mixture. Add the remaining amount 18 of fuel. Mix (shake) the fuel-mix thoroughly before filling the fuel tank. Fueling 19 WARNING ● Always shut off the engine before refueling. ● Slowly open the fuel tank, when filling up with fuel, so that possible over-pressure disappears. ● Tighten the fuel cap carefully, after fueling. ● Always move the trimmer at least 10 ft (3 m) from the fueling area before starting. ● Always wash any spilled fuel from clothing immediately with soap. ● Be sure to check for any fuel leakage after refueling. Fig. 14 2. Set choke lever (20) to START position (closed) (A). (Fig. 15) 20 B B Before fueling, clean the tank cap area carefully, to ensure that no dirt falls into the tank. Make sure that the fuel is well mixed by shaking the container, A before fueling. Starting CAUTION Before starting, make sure the cutting attachment does not touch anything. 1. Set ignition switch (16) to forward away from stop position. (Fig. 13) Fig. 15 3. Pull recoil starter briskly, taking care to keep the handle in your grasp and not allowing it to snap back. (Fig. 16) 16 17 Fig. 13 * Push priming bulb (18) several times so that fuel flows through return pipe (19). (Fig. 14) Fig. 16 4. When you hear the engine want to start, return choke lever to RUN position (open) (B). Then pull recoil starter briskly again. NOTE If engine does not start, repeat procedures from 2 to 4. 5. Then allow the engine about 2-3 minutes to warm up before subjecting it to any load. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
11
English
Always start by
fi
ling half the amount of fuel, which
is to be used. Then add the whole amount of oil. Mix
(shake) the fuel mixture. Add the remaining amount
of fuel.
Mix (shake) the fuel-mix thoroughly before
fi
lling the
fuel tank.
Fueling
WARNING
●
Always shut o
ff
the engine before refueling.
●
Slowly open the fuel tank, when
fi
lling up
with fuel, so that possible over-pressure
disappears.
●
Tighten the fuel cap carefully, after fueling.
●
Always move the trimmer at least 10 ft (3 m)
from the fueling area before starting.
●
Always wash any spilled fuel from clothing
immediately with soap.
●
Be sure to check for any fuel leakage after
refueling.
Before fueling, clean the tank cap area carefully,
to ensure that no dirt falls into the tank. Make sure
that the fuel is well mixed by shaking the container,
before fueling.
Starting
CAUTION
Before
starting,
make
sure
the
cutting
attachment does not touch anything.
1. Set ignition switch (16) to forward away from stop
position. (Fig. 13)
17
16
Fig. 13
*
Push priming bulb (18) several times so that
fuel
fl
ows through return pipe (19). (Fig. 14)
18
19
Fig. 14
2. Set choke lever (20) to START position (closed)
(A). (Fig. 15)
A
B
20
B
Fig. 15
3. Pull recoil starter briskly, taking care to keep the
handle in your grasp and not allowing it to snap
back. (Fig. 16)
Fig. 16
4. When you hear the engine want to start, return
choke lever to RUN position (open) (B). Then pull
recoil starter briskly again.
NOTE
If engine does not start, repeat procedures from
2 to 4.
5. Then allow the engine about 2–3 minutes to
warm up before subjecting it to any load.