Tanaka TCS33EDTP/14 Owner's Manual - Page 7
Tanaka TCS33EDTP/14 Manual
View all Tanaka TCS33EDTP/14 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 7 highlights
English O Never use the saw with only one hand. You cannot control the saw properly and you may lose control and injure yourself severely. Keep the saw body close to your body to improve control and reduce strain. When cutting with the bottom part of the chain the reactive force will pull the saw away from you towards the wood you are cutting. The saw will control the feeding speed and sawdust will be directed towards you. (Fig. 20) 77, Before felling a tree, carefully consider all conditions which may effecrithe intended direction, such as: Angle of the tree. Shape of the crown. Snow load on the crown. Wind conditions. Obstacles within tree range (e.g., other trees, power lines, roads, buildings, etc.). WARNING O Always observe the general conditions of the tree. Look for decay and rot in the trunk which will make it more likely to snap and start to fall before you expect it. O Look for dry branches, which may break and hit you when you are working. Always keep animals and people at least twice the tree length away while felling. Clear away shrubs and branches from around the tree. Prepare a path of retreat away from the felling direction. Fig. 20 O When cutting with the upper part of the chain the reactive force will push the saw towards you and away from the wood you are cutting. (Fig. 21) • Fig. 21 O There is a risk of kickback if the saw is pushed far enough so that you begin to cut with the nose of the bar. The safest cutting method is to cut with the bottom part of the chain. Sawing with the upper part makes it much more difficult to control the saw and increases the risk of kickback. O In case the chain locked, immediately release the throttle trigger. If the throttle trigger keeps rotating at high speed with the chain locked, the clutch will overheat causing trouble. NOTE Always keep the spiked bumper (if so equipped) face to a tree, because the chain may suddenly be drawn into a tree. FELLING Felling is more than cutting down a tree. You must also bring it down as near to an intended place as possible without damaging the tree or anything else. BASIC RULES FOR FELLING TREES Normally the felling consists of two main cutting operations, notching and making the felling cut. Start making the upper notch cut on the side of the tree facing the feeling direction. Look through the kerf as you saw the lower cut so you do not saw too deep into the trunk. The notch should be deep enough to create a hinge of sufficient width and strength. The notch opening should be wide enough to direct the fall of the tree as long as possible. Saw the felling cut from the other side of the tree between one and two inches (3-5 cm) above the edge of the notch. (Fig. 22) 19 I~ ill 3/4 Ij ~1/4 I;l4, III!1 20 Jbki 22 \ 21 Fig. 22 19. Felling direction 20. 45° minimum notch opening 21. Hinge 22. Felling cut Never saw completely through the trunk. Always leave a hinge. The hinge guides the tree. If the trunk is completely cut through, you lose control over the felling direction. Insert a wedge or a felling lever in the cut well before the tree becomes unstable and starts to move. This will prevent the guide bar from binding in the felling cut 12 English if you have misjudged the falling direction. Make sure no people have come into the range of the falling tree before you push it over. FELLING CUT, TRUNK DIAMETER MORE THAN TWICE GUIDE BAR LENGTH Cut a large, wide notch. Then cut a recess into the center of the notch. Always leave a hinge on both sides of the center cut. (Fig. 23) Fig. 25 Stand on the left side of the trunk. Maintain a secure footing and rest the saw on the trunk. Hold the saw close to you so that you are in full control of it. Keep well away from the chain. Move only when the trunk is between you and the chain. Watch out for spring back of limbs under tension. Fig. 23 Complete the felling cut by sawing around the trunk as in the Fig. 24. LIMBING THICK BRANCHES When limbing thick branches, the guide bar may get pinched easily. Branches under tension often snap up, so cut troublesome branches in small steps. Apply the same principles as for cross cutting. Think ahead and be aware of the possible consequences of all your actions. CROSS CUTTING/BUCKING Before starting to cut through the log, try to imagine what is going to happen. Look out for stresses in the log and cut through it in such a manner that the guide bar will not get pinched. Fig. 24 & WARNING These methods are extremely dangerous because they involve the use of the nose of guide bar and can result in kickback. Only properly trained professionals should attempt these techniques. LIMBING Limbing is removing the branches from a feller tree. & WARNING A majority of kickback accidents occurduring limbing. Do not use the nose of the guide bar. Be extremely cautious and avoid contacting the log, other limbs or objects with the nose of the guide bar. Be extremely cautious of limbs under tension. They can spring back towards you and cause loss of control resulting in injury. (Fig. 25) CROSS CUTTING LOGS, PRESSURE ON TOP Take a firm stance. Begin with an upper cut. Do not cut too deeply, about 1/3 of the log diameter is enough. Finish with a bottom cut. The saw cuts should meet. (Fig. 26) 25 23 - 24 27 28 Qj Fig. 26 23. Relieving cut 24. Cross cut 25. Pressure on top 26. Pressure side 27. Tension side 28. Relative depth of saw cuts 13