Thermador PRG486WDG Installation Instructions - Page 26

Data rating label, Burner test

Get Thermador PRG486WDG PDF manuals and user guides View all Thermador PRG486WDG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Data rating label Data rating label The data rating label shows the model and serial number of your appliance. The slide-out plates can be accessed as shown below. • Burner flames are too high. • Flames shoot out of burners. • Burners do not ignite. • Burner flames light unevenly. • Burner emits gas odor. Burner cap placement Each cap has a letter (B, D, or F) cast in the underside of the cap that corresponds to a letter (B, D, or F) cast in the burner base that is attached to the appliance. To place the burner caps 1. Place each burner cap on its correct burner base per its corresponding letter designation. Electric wiring diagrams and schematics The electric wiring diagrams and schematics are attached behind the toe kick, and should not be removed except by a service technician, then replaced after service. Burner test 9 WARNING To prevent flare-ups and avoid the creation of harmful by-products, do not use the cooktop without all burner caps and all burner grates properly positioned. 9 WARNING To prevent burns, do not touch burner caps or grates while hot. Turn the cooktop off and allow the burners to cool. Install any loose components, such as burner caps and grates that may have been removed earlier. Be certain that burner caps seat properly into the burner bases. Before testing operation of the appliance, verify that the unit and the gas supply have been carefully checked for leaks and that the unit has been connected to the electrical power supply. Turn the manual gas shut-off valve to the open position. The burner caps must be properly placed on the burner bases for the cooktop to function properly. If the burner cap is not properly placed, one or more of the following problems may occur: 2. Place burner cap gently on top of base so that the prongs of the burner base fit snugly into the groove of the burner cap. Checking the burner cap placement • Check each burner to make sure there is no gap between the burner cap and burner base. • You may gently try to move the burner caps from side to side to check if the caps are properly placed on the burner bases. • When properly placed, each burner cap will rest flat on top of its burner base, and completely cover the star-shape of the burner base when viewed from the top as shown below. Page. 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Page. 25
Data rating label
Data rating label
The data rating label shows the model and serial number
of your appliance. The slide-out plates can be accessed as
shown below.
Electric wiring diagrams and schematics
The electric wiring diagrams and schematics are attached
behind the toe kick, and should not be removed except by
a service technician, then replaced after service.
Burner test
9
WARNING
To prevent flare-ups and avoid the creation of harmful
by-products, do not use the cooktop without all
burner caps and all burner grates properly positioned.
9
WARNING
To prevent burns, do not touch burner caps or grates
while hot. Turn the cooktop off and allow the burners
to cool.
Install any loose components, such as burner caps and
grates that may have been removed earlier. Be certain that
burner caps seat properly into the burner bases. Before
testing operation of the appliance, verify that the unit and
the gas supply have been carefully checked for leaks and
that the unit has been connected to the electrical power
supply. Turn the manual gas shut-off valve to the open
position.
The burner caps must be properly placed on the burner
bases for the cooktop to function properly. If the burner
cap is not properly placed, one or more of the following
problems may occur:
•
Burner flames are too high.
•
Flames shoot out of burners.
•
Burners do not ignite.
•
Burner flames light unevenly.
•
Burner emits gas odor.
Burner cap placement
Each cap has a letter (B, D, or F) cast in the underside of
the cap that corresponds to a letter (B, D, or F) cast in the
burner base that is attached to the appliance.
To place the burner caps
1.
Place each burner cap on its correct burner base per
its corresponding letter designation.
2.
Place burner cap gently on top of base so that the
prongs of the burner base fit snugly into the groove of
the burner cap.
Checking the burner cap placement
•
Check each burner to make sure there is no gap
between the burner cap and burner base.
•
You may gently try to move the burner caps from side
to side to check if the caps are properly placed on the
burner bases.
•
When properly placed, each burner cap will rest flat
on top of its burner base, and completely cover the
star-shape of the burner base when viewed from the
top as shown below.