Toshiba 55A60R Owners Manual - Page 12

Programming the remote control for use with a, VCR or a cable TV converter

Get Toshiba 55A60R PDF manuals and user guides View all Toshiba 55A60R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Introduction Connecting your TV Using the Remote Control To control a cable TV converter: Program the remote control to recognize the brand of your converter. The shaded buttons shown on the right will control the cable TV converter. Set the TV/CABLE/VCR switch to the CABLE position. Programming the remote control for use with a VCR or a cable TV converter This remote control is pre-programmed to operate Toshiba VCRs. To use VCRs or cable converters other than Toshiba models, you must follow the steps below before you operate your remote control. 1. Refer to the "VCR code table" or "Cable TV converter code table" on pages 13-14 to find the number that corresponds to the brand name of your VCR or converter. If more than one number is listed, try each one separately until you find the one that works. 2. If you are reprogramming the remote control to operate your: • VCR, set the TV/CABLE/VCR switch on the remote control to VCR. • Cable converter, set the TV/CABLE/VCR switch on the remote control to CABLE. 3. Hold down the RECALL button while using the Number buttons (0-9) to enter the three-digit code number of your brand of VCR or converter. 4. Point the remote control at the VCR or converter and press POWER to test the code number. If the VCR or converter turns on, you have entered the right number. If the VCR or converter does not respond to the remote control, you may have entered the wrong number. Repeat steps 1-4 with another code number. 5. Reset the TV/CABLE/VCR switch to TV to control the TV. RECALL MUTE POWER 123 456 78 9 CH RTN 100 0 ENT RECALL POWER Channel Number Enter CH MENU/ VOL ENTER VOL TV CABLE VCR CH EX I T Channel yz Note: • Each time you replace the batteries, you must reprogram the remote control. • Some newer VCRs are capable of working on either of two remote codes. These VCRs have a switch labeled "VCR1/VCR2." If your VCR has this kind of switch, it may not respond to any of the code numbers for your VCR brand name. In this case, set the switch to the other position (VCR1 or VCR2) and reprogram the remote control. For future reference, write down the code numbers you used: VCR code Cable code Setting up your TV Using the TV's Features Appendix Index 12 Downloaded from www.Manualslib.com manuals search engine

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
12
To control a cable TV converter:
Program the remote control to recognize the brand of your
converter. The shaded buttons shown on the right will control the
cable TV converter.
Set the TV/CABLE/VCR switch to the CABLE position.
Programming the remote control for use with a
VCR or a cable TV converter
This remote control is pre-programmed to operate Toshiba VCRs. To
use VCRs or cable converters other than Toshiba models, you must
follow the steps below before you operate your remote control.
1.
Refer to the “VCR code table” or “Cable TV converter code
table” on pages 13-14 to find the number that corresponds to the
brand name of your VCR or converter.
If more than one number is listed, try each one separately until
you find the one that works.
2.
If you are reprogramming the remote control to operate your:
•
VCR,
set the TV/CABLE/VCR switch on the remote control
to VCR.
•
Cable converter,
set the TV/CABLE/VCR switch on the
remote control to CABLE.
3.
Hold down the RECALL button while using the Number
buttons (0-9) to enter the three-digit code number of your brand
of VCR or converter.
4.
Point the remote control at the VCR or converter and press
POWER to test the code number.
If the VCR or converter turns on, you have entered the right
number.
If the VCR or converter does not respond to the remote control,
you may have entered the wrong number. Repeat steps 1-4 with
another code number.
5.
Reset the TV/CABLE/VCR switch to TV to control the TV.
For future reference, write down the code numbers you used:
VCR code
_____________________
Cable code
_____________________
Note:
•
Each time you replace the batteries, you
must reprogram the remote control.
•
Some newer VCRs are capable of working
on either of two remote codes. These VCRs
have a switch labeled “VCR1/VCR2.”
If your VCR has this kind of switch, it may
not respond to any of the code numbers for
your VCR brand name. In this case, set the
switch to the other position (VCR1 or
VCR2) and reprogram the remote control.
TV
CABLE
VCR
E
X
I
T
1
2
3
4
5
6
7
8
9
100
0
ENT
POWER
MUTE
CH RTN
RECALL
CH
VOL
MENU/
ENTER
VOL
CH
POWER
Channel
yz
Channel
Number
Enter
RECALL
Downloaded from
www.Manualslib.com
manuals search engine