Home » Toshiba Manuals » Servers » Toshiba Magnia Z310 » Manual Viewer

Toshiba Magnia Z310 User Guide - Page 60

Switching off the server

View all Toshiba Magnia Z310 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Getting Started Switching off the server 41 Switching off the server The method for switching off the server varies depending on the operating system used. Check the operating system and switch the server off using the normal method or use the automatic shutdown function. Every time the server is to be switched off, use only one of the methods mentioned above. Using both methods simultaneously, will cause the server to fail during its normal shutdown operation. Normal shutdown If no automatic shutdown function is installed in the operating system, switch the server off by using the normal shutdown procedure as follows. 1 Prepare the server system for switching it off by the normal method. Method to shut down the operating system See "User's Manual for the Operating System." 2 Press the power/sleep button. Using the automatic shutdown function The automatic shutdown function is only available when the server runs under the Windows NT or Windows 2000 operating system. If the power/sleep button is pressed on another operating system, the server is immediately switched off without the preliminary process necessary for shutdown. In the case the exclusive automatic shutdown software is not installed in the Windows NT or Windows 2000 operating system, no automatic shutdown operation is executed and the server is switched off without the preliminary process as the power/sleep button is pressed. When the automatic shutdown function is not used, be sure to execute the preliminary process required for quitting the operating system before pressing the power/sleep button.

Section	Page
MAGNIA™ Z310 User’s Guide	1
Model: MAGNIA Z310	2
Warning Label	2
power supply unit (System Unit)	2
power supply unit (External Unit)	2
CD-ROM Safety Instruction	4
Location of the required label	4
Copyright	5
Disclaimer	6
Trademarks	6
Introduction	8
About this guide	9
Safety cautions	10
Other icons used	11
Other documentation	11
Service options	12
Maintenance contracts	12
Contents	13
Chapter 1: Getting Started 2	13
Chapter 2: Installing and Removing Hardware 48	15
Chapter 3: External Unit Setup 110	15
Chapter 4: System Configuration Setup 138	16
Chapter 5: Installing Software 170	17
Chapter 6: Troubleshooting 190	18
Appendix A: Specifications 202	18
Appendix B: Interfaces 208	19
Appendix C: Switch Setting 218	19
Appendix D: Trouble Information 222	19
Appendix E: Unit Logs 228	19
Chapter 1	20
Getting Started	21
Checking the items included with the server	21
Mounting optional internal devices	23
Environmental considerations	24
Micro Tower Type/Rack Type	24
Micro Tower Type	26
Minimum clearances required for horizontal installation	26
Minimum clearances required for vertical installation	26
Rack Type	27
Minimum clearances for installation	27
Power requirements	28
Front view (with the front panel closed)	29
Front view with the front panel closed	29
Key lock	29
Key lock	29
Front view (with the front panel opened)	30
Front view of the Micro Tower Type	30
Opening the front panel	30
Removing the front panel	31
(2) Operation buttons	31
Operation buttons	31
(3) System status indicators	33
System status indicators	33
(4) Front panel display	35
1. System configuration	35
2. User messages	35
3. Trouble information	36
4. Bootup/shutdown messages	36
(5) Card slot	37
(6) USB connector	37
(7) Device bay	37
(8) HDD/LAN status indicators	38
Rear view	41
Rear view of the server	41
(2) Security Loop	41
I/O connectors	42
I/O connectors	42
Expansion slot	43
LAN status indicators	43
Inside the server	44
Inside the server	44
(1) Motherboard	44
(2) SCSI riser card	44
(3) Cooling fans	45
(4) CPU sockets	45
(5) Memory slots	45
(6) Expansion slot	45
(7) IDE HDD cage	45
(8) Board for wireless card	45
Connecting peripheral devices	45
How to connect peripheral devices	45
1 Make sure that all the power buttons of the server and external units are turned off.	46
2 If the power cables of the server and external units are connected to an AC outlet, pull the pl...	46
3 Connect each of the peripheral devices to a proper connector on the server with an interface ca...	46
Connecting peripheral devices (Front view)	46
Connecting peripheral devices (Rear view)	47
4 If a connector is provided with screws for securing connection, tighten the screws without fail.	47
5 After making sure that all the peripheral units are properly connected, plug the power cables o...	47
Connecting the power cable	49
1 Connect the power cable to the connector on the back of the server.	49
Connecting the power cable	49
2 Plug the power cable into an AC outlet or the power output connector of an uninterruptible powe...	49
Switching on the server	51
Turning on the server	51
1 Check to see if all of the peripheral devices such as a display, keyboard, mouse, etc. are corr...	51
2 Check to see if the power cables of the System Unit and External Units are connected with AC ou...	51
3 Turn on the display.	51
4 Open the front panel.	51
5 Press the power/sleep button.	51
Pressing the power/sleep button.	51
Turning on the server by the “Remote Management” function	52
POST (Power On Self-Test)	52
Starting up the system	53
Starting up with the floppy disk	53
1 Attach the USB floppy disk drive to the USB port located at the front of the machine.	53
2 Place the startup disk in the floppy disk drive.	53
3 Switch on the power/sleep button.	53
Starting up by the hard disk drive unit (in the case the OS has been installed)	54
1 Make sure that a bootable FDD or CD-ROM is not in the respective drive unit.	54
2 Turn on the power/sleep button.	54
Starting up by the CD-ROM	55
1 Make sure that no floppy disk is placed in the floppy disk drive.	55
2 Switch on the power/sleep button.	55
3 Immediately after switching on the power/sleep button, press the eject button of the CD-ROM dri...	55
BIOS setup	55
Making a floppy disk	56
How to make a backup floppy disk	56
1 Place both the “Toshiba Server Setup Tool CD-ROM” and the “Startup Disk floppy disk” in to thei...	56
2 Select “Utility.”	56
3 Select “Making FD.”	56
4 Select the name of the floppy disk to create and select “OK.”	56
5 Place a 1.44MB formatted floppy disk in to the disk drive and select “OK.”	56
Setup of system configuration	57
BIOS setup utility	57
SCSI utility	57
IDE RAID Setup utility	57
Setup of disk array (RAID)	58
Installing software	59
Switching off the server	60
Normal shutdown	60
1 Prepare the server system for switching it off by the normal method.	60
2 Press the power/sleep button.	60
Using the automatic shutdown function	60
1 Execute the specified shut down process for the application software running on the operating s...	61
2 Press the power/sleep button to turn off the server.	61
3 Make sure that the power indicator () is amber and the server operation is stopped normally. If...	61
Notes on use of the automatic shutdown function	62
Hints on operation of the power/sleep button	62
Logon by a user without shutdown rights	63
The application in operation	63
Load to the system	63
Abnormal system shutdown	64
Chapter 2	65
Installing and Removing Hardware	66
Before starting operation	66
Before starting operation	67
Screw head and screwdriver	68
Installing/removing an optional device	70
1 Carefully read the precautions mentioned in this chapter (Before starting operation) and check ...	70
2 Switch off all the peripheral units connected with the server.	70
3 If the server is running, shut it down and switch off the power.	70
4 Unplug the power cable of the server from the AC outlet or UPS (uninterruptible power supply), ...	70
5 Remove the outer covers and server panels from the server.	70
6 Install or remove an optional device.	70
7 Ensure that there is neither tool nor dead part remaining inside the server.	70
8 Attach the server panels and outer covers to the server.	71
9 Connect the peripheral units and switch them on.	71
10 Plug the server's power cable connector into an AC outlet (or UPS) and then switch on the server.	71
Removing and replacing the server panels	72
Removing the top panel (for Micro Tower Types)	72
1 Shut down the server and turn off the power if it is in operation.	72
2 Unplug the power cable.	72
3 Remove four screws and the outer cover (upper).	72
Removing the outer cover (upper)	72
4 Remove the front panel. See “Front panel” on page11	73
5 Remove seven screws and the top panel.	73
Removing the top panel	73
Replacing the top panel (for Micro Tower Types)	73
1 Replace the top panel to the server carefully so that it does not catch any cable.	73
2 Attach seven screws and fix the top panel.	73
3 Attach the outer cover (upper) and fix it by four screws.	73
4 Attach the front panel.	73
5 Plug the power cable.	73
Removing/replacing the top panel (for Rack Types)	73
When using a Rack Type	74
Rack assembly procedure	74
1 Decide on where to assemble the server.	75
Decide on where to assemble the server	75
2 Temporarily fasten Rail R to the posts on the left and right of the rack rear, and Rail F (L) a...	76
Temporarily fasten the Rails	76
3 Fix Rail R on the left and right, Rail F (L) and Rail F (R) with two Screws (M5).	76
Fix Rail F and Rail R	76
4 Attach Pin Catch Tray to Rail F (L) and Rail F (R) with two Screws (M5).	77
Attach Pin Catch Tray	77
5 Attach Washer, Spring Washer and Guide Pin (M6) at two locations to the Base assembly.	77
Attach the Guide Pin	77
6 Insert the Base Assembly into the Rail, and insert Guide Pin (M6) into the Pin Catch Tray.	78
Insert the Base Assembly	78
7 Attach the Support Bracket (L) and Support Bracket (R) on the Base Assembly and fix them with t...	78
Attach the Support Brackets	78
8 Fix the Base Assembly to the rack with the claw screws on the front.	79
Fix the Base Assembly	79
9 Tighten the eight screws temporarily fastened in step 2.	79
Fix Rails	79
10 Attach Washer, Spring Washer and Guide Pin (M6) on the back.	80
Attaching the Guide Pin	80
11 Attach the Front Bracket (L) or Front Bracket (R) to the server bay with Screws (M3).	80
Attach the Front Bracket	80
12 Place the server bay on the Base Assembly and insert.	81
Insert the server bay	81
13 Loosen the claw screw to draw out the Base Assembly by about 100 mm.	81
Drawing out the Base Assembly	81
14 Fix the Base Assembly to the server housing with a screw (M3).	82
Fixing the Server Housing	82
Fixing the Blank Bracket	82
15 Insert the entire Base Assembly into the rack.	83
Inserting Into Rack Blank Module	83
16 Fix the housing on the left and right with the claw screws of Front Bracket (L) and Front Brac...	83
Fix the housing on the left and right	83
Sliding the server out of or into the rack	84
Sliding the server (Rack Type) out of the rack	85
1 If the server is running, shut it down and turn off the power.	85
2 Switch off all the peripheral units connected with the server.	85
3 Unplug the power cable of the server from the AC outlet or UPS (uninterruptible power supply).	85
4 Unplug all the cables from the server.	85
5 Loosen the four claw screws which fix the Base Assembly and draw out the Base Assembly.	85
Drawing out the Base Assembly	85
6 Remove the screw (M3) fixing the Base Assembly to the server.	85
Removing the screw	86
7 Slide the server out of the rack.	86
Sliding the server (Rack Type) into the rack	86
1 Gently slide the server into the rack, according to the rack assembly procedure step 10 - 15.	86
2 When it is located in place, fix the server with four screws.	86
3 Connect the cables disconnected.	86
Power Supply Unit	87
Removing the power supply unit	87
1 If the server is in operation, shut it down first and cut off the power supply to it.	87
2 Unplug the power cable from the AC outlet.	87
3 Remove the outer covers and server panels from the server.	87
4 Remove six screws, lift up the power supply unit by sliding forward slightly.	87
Lifting up the power supply unit.	87
5 Disconnect the power cable and signal cable.	88
Disconnecting the cables	88
Installing the power supply unit	88
1 Confirm that the power supply is cut off.	88
2 Confirm that the power cable is disconnected from the AC outlet.	88
3 Remove the outer covers and server panels from the server.	88
4 Connect the power cable and signal cable.	89
Connecting the cables	89
5 Install the power supply unit, slide back slightly and fix it with six screws.	89
Installing the power supply unit	89
6 Attach the server panels and outer covers.	89
Memory module	90
Memory slots	92
Installing an additional memory module	92
1 If the server is in operation, shut it down first and cut off the power supply to it.	93
2 Unplug the power cable from the AC outlet.	93
3 Remove the outer covers and server panels from the server.	93
4 Remove the power supply unit.	93
5 Extend the hooks on both sides of the memory slot outwards.	93
Extend the hooks	93
6 Insert the memory module into the proper memory slot, paying heed to the position of each notch...	94
Installing a memory module	94
7 Install the power supply unit.	94
8 Attach the server panels and outer covers.	94
9 Connect the power cable of the server to the power supply and switch on the server.	94
Removing a memory module	95
1 If the server is in operation, shut it down and switch off power.	95
2 Unplug the power cable from the AC outlet.	95
3 Remove the outer covers and server panels from the server.	95
4 Remove the power supply unit.	95
5 Extend the hooks on both sides of the memory slot outwards and remove the memory module out of ...	95
Removing a memory module	95
6 Install the power supply unit.	96
7 Fit the server panels and outer covers to the server.	96
8 Connect the power cable of the server to the power supply and switch on the server	96
CPU module	96
CPU socket	96
Installing the CPU module	97
1 If the server is running, shut it down and turn off the power.	97
2 Unplug the power cable.	97
3 Remove the server panels.	97
4 Remove two screws that fix the PCI bracket, and remove the PCI bracket.	97
Removing the PCI bracket	98
5 Remove one screw that fix the riser card and remove the riser card.	99
Removing the riser card	99
6 Remove two screws and the fan duct.	100
Removing the fan duct	100
7 Raise the lock lever of the expansion CPU socket.	100
Raising the lock lever	100
8 Align the CPU pins correctly with the holes in the socket, and insert the CPU module as far as ...	101
Inserting the CPU module	101
9 Push down the lock lever of the socket until it is hooked securely.	101
Pushing down the lock lever	101
10 Detach the cover from the thermal seat on the contact surface between the heat sink and the CP...	101
11 Lightly push the heat sink in the direction of the socket, and fix it by engaging the clips wi...	102
Attaching the heat sink	102
Fixing the clips	102
12 Attach the fan duct and fix it with two screws.	103
Attaching the fan duct	103
13 Attach the riser card and fix it with one screw.	103
Attaching the riser card	103
14 Fix the PCI bracket with two screws.	103
Fixing the PCI bracket	104
15 Install the server panels.	104
16 Connect the power cable of the server to the power supply and switch on the server.	104
17 Confirm that the CPU module is recognized properly with the display on the screen.	104
Replacing the CPU module	105
1 If the server is running, shut it down and turn off the power.	105
2 Unplug the power cable.	105
3 Remove the server panels.	105
4 Remove two screws that fix the PCI bracket, and remove the PCI bracket.	105
Removing the PCI bracket	106
5 Remove one screw that fix the riser card, and remove the riser card.	106
Removing the riser card	106
6 Remove two screws and the fan duct.	107
Removing the fan duct.	107
7 Release the clips that secure the heat sink for the CPU module to be removed, and remove the he...	107
Releasing the clips	108
Removing the heat sink	108
8 Raise the lock levers of the socket in which the CPU module you want to remove is mounted.	108
Raising the lock lever	108
9 Remove the CPU module.	109
Removing the CPU module	109
10 Install a new CPU module in the same procedure as for extension.	109
11 Install the fan duct and fix it with two screws.	109
Installing the fan duct	109
12 Install the riser card on the motherboard and fix it with one screw.	110
Installing the PCI riser card	110
13 Fix the PCI bracket with two screws.	110
Fixing the PCI bracket	110
14 Install the server panels.	110
15 Connect the power cable of the server to the power supply and switch on the server.	110
16 Confirm that the replaced CPU module is recognized properly with the display on the screen.	110
Internal battery	112
Replacing the internal battery	113
1 Write down the system configuration information.	113
2 Shut down and turn off your server.	113
3 Unplug the power cable.	113
4 Remove the server panels.	113
5 Remove the power supply unit.	113
6 Remove four screws and the board for the wireless card.	113
Removing the board for the wireless card	113
7 Put your fingers below the battery, and pull it up.	114
Removing the battery	114
8 Install a new battery with polarity (+) up.	114
Installing the battery	114
9 Install the board for the wireless card and fix it with four screws.	115
Installing the board for the wireless card	115
10 Install the power supply unit.	115
11 Install the server panels.	115
12 Connect the power cable of the server to the power supply, and switch on the server.	115
13 Set the server according to the System Time, System Date and system configuration information ...	115
Hard Disk Drive (HDD) –IDE HDD–	116
Installing the hard disk drive	116
1 If the server is running, shut it down and turn off the power.	116
2 Unplug the power cable.	116
3 Remove the front panel. See “Front panel” on page11.	116
4 Tilt over the detachable lever of the slot where you want to install a hard disk drive, by pull...	116
Pulling the detachable lever toward you	116
5 Pull out the HDD slot spacer that was extracted partially.	117
6 Push the hard disk drive completely into the slot where you want to mount it.	117
Installing the hard disk drive	117
7 Close the detachable lever and fix it.	117
Fixing the detachable lever	117
8 Attach the front panel.	117
9 Connect the power cable of the server to the power supply, and switch on the server.	118
Replacing a hard disk drive during operation	118
1 Remove the front panel.	119
2 Confirm the position of a faulty device.	119
3 Start the MegaRAID Configuration Console (MCC).	119
4 Tilt over the detachable lever of the slot which holds a defective hard disk drive, by pulling ...	119
Pulling the detachable lever toward you	119
5 While holding the disk tray, carefully remove the hard disk drive that is pulled out halfway.	119
Pulling out the hard disk drive	120
6 Install a new hard disk drive in the same procedure as for extension.	120
7 After a short time, confirm that the PWR indicator lights up.	120
8 Attach the front panel.	120
9 Click the “Scan Device” of the MCC screen.	120
10 Rebuild array starts automatically.	120
Expansion cards	121
Expansion slots	121
Restrictions on PCI expansion cards	121
Installing the expansion card	122
1 If the server is running, shut it down and turn off the power.	122
2 Unplug the power cable.	122
3 Remove the server panels.	122
4 Remove two screws and the PCI bracket.	123
Removing the PCI bracket	123
5 Remove one screw and the PCI slot cover from the PCI bracket.	123
Removing the PCI slot cover	123
6 Install the PCI bracket on the expansion card and fix it by one screw.	124
Installing the PCI bracket	124
7 Remove one screw and the riser card.	124
Removing the PCI riser card	124
8 Insert the expansion card in the riser card.	125
Inserting the expansion card	125
9 Install the riser card on the motherboard and fix it by one screw.	126
Installing the riser card	126
10 Fix the PCI bracket with two screws.	126
Fixing the PCI bracket	126
11 Install the power supply unit.	126
12 Install the server panels.	126
13 Connect the power cable of the server to the power supply, switch on the server.	126
Chapter 3	127
External Unit Setup	128
Types of External Unit	128
Front view of the External Hard Drive Unit Z1 (with the front panel closed)	129
Front view with the front panel closed	129
Key lock	129
Key lock	129
Front view of the External Hard Drive Unit Z1 (with the front panel opened)	130
Front view of the Micro Tower Type	130
(1) Front panel	130
(2) Operation button	131
Operation button	131
(3) System status indicators	132
System status indicators	132
(4) HDD status indicators	133
HDD status indicators	133
Rear view of the External Hard Drive Unit Z1	135
Rear view of the External Hard Drive Unit Z1	135
AC power connector	135
I/O connectors	135
I/O connectors	135
(1) External Unit control connector IN/OUT ()	135
(2) SCSI connector ()	136
Installing and Removing Hard Disk Drive (HDD) -SCSI HDD-	136
Installing the hard disk drive	136
1 Remove the front panel.	137
Removing the front panel	137
2 Tilt over the detachable lever of the slot where you want to install a hard disk drive, by pull...	137
Pulling the detachable lever toward you	137
3 Pull out the HDD slot spacer that was extracted partially.	137
4 Push the hard disk drive completely into the slot where you want to mount it.	137
Installing the hard disk drive	138
5 Close the detachable lever and fix it.	138
Fixing the detachable lever	138
6 Attach the front panel.	138
Replacing a hard disk drive during operation	139
1 Remove the front panel.	140
Removing the front panel	140
2 Confirm the position of a faulty disk.	140
3 Tilt over the detachable lever of the slot which holds a defective hard disk drive, by pulling ...	140
Pulling the detachable lever toward you	140
4 While holding the disk tray, carefully remove the hard disk drive that is pulled out halfway.	141
Pulling out the hard disk drive	141
5 Install a new hard disk drive in the same procedure as for extension.	141
6 After a short time, confirm that the DC POWER indicator () lights up.	141
7 Attach the front panel.	141
8 Recover (rebuild) the disk.	141
Setup of disk array (RAID)	142
Front view of the External Device Bay Unit Z1 (with the front panel closed)	143
Front view with the front panel closed	143
Key lock	143
Key lock	143
Front view of the External Device Bay Unit Z1 (with the front panel opened)	144
Front view of the Micro Tower Type	144
(1) Front panel	144
(2) Operation button	145
Operation button	145
(3) System status indicators	146
System status indicators	146
Rear view of the External Device Bay Unit Z1	147
Rear view of the External Device Bay Unit Z1	147
AC power connector	147
I/O connectors	147
I/O connectors	147
(1) External Unit control connector IN/OUT ()	147
(2) SCSI connector ()	148
Installing SCSI device	148
Terminator	148
SCSI ID	148
Changing the SCSI ID	148
1 If the server is running, shut it down and turn off the power.	148
2 Disconnect the AC power cable.	148
3 Open the front panel.	149
4 Remove four screws and remove the outer cover (upper).	149
Removing the outer cover	149
5 Remove seven screws and remove the top cover.	149
Removing the top cover	149
6 Remove the power and signal cables.	150
Removing the cables	150
7 Remove four screws that fix the SCSI device.	150
Removing the screws	150
8 Pull out the SCSI device completely.	151
Remove the SCSI device	151
9 Set the SCSI ID so that it would not be the same as other device.	151
10 Insert the SCSI device into the unit.	151
11 Attach the four screws and fix the SCSI device.	151
Installing the SCSI device	151
12 Connect the power and signal cables.	152
Connecting the cables	152
13 Attach the top cover and fix it with seven screws.	152
Attaching the top cover	152
14 Attach the outer cover (upper) and fix it with four screws.	153
Attaching the outer cover	153
15 Close the front panel.	153
16 Connect the power cable of the server to the power supply and switch on the server.	153
How to Connect External Unit	153
1 Connect each Units in the following order : System Unit Æ External Hard Drive Unit Z1 Æ Externa...	154
2 When one External Hard Drive Unit Z1 is connected with SCSI connector in the backside of System...	154
3 When the RAID Card which has Two SCSI channels is installed, connect each Units in the channel ...	154
Connecting the External Units	154
Chapter 4	155
System Configuration Setup	156
BIOS setup utility	156
Starting the setup utility	157
Menu screen	158
Menu configuration	158