Toshiba Portege R500-S5008X Resource Guide for Portege R500 Series - XP - Page 31

Removing a memory module, Press Any Key to Continue

Get Toshiba Portege R500-S5008X PDF manuals and user guides View all Toshiba Portege R500-S5008X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Adding memory (optional) 31 15 Re-insert the main battery. For more information on inserting the main battery, see "Inserting a charged battery" on page 42. 16 Turn the computer right side up. 17 Reconnect the cables. 18 Restart the computer. TECHNICAL NOTE: You must have at least one memory module installed for the computer to work. Removing a memory module If you need to remove a memory module: 1 Complete steps 1-8 in "Installing a memory module" on page 27 to shut down the computer and open the memory module slot cover. Do not try to remove a memory module with the computer turned on. You can damage the computer and the memory module. Do not remove the memory module while the computer is in Standby or Hibernation mode. The computer could hang up the next time you turn it on and data in memory will be lost. In either of the above cases, the Standby configuration will not be saved. The following message appears when you turn on the power: Warning: Resume Failure Press Any Key to Continue If the computer hangs up when you turn it on, perform the following: Press the power button and hold it down for at least ten seconds, then turn the power on again. 2 Pull the latches away from the memory module. The memory module pops up slightly. 3 Gently lift the memory module to a 30-degree angle and slide it out of the slot. 4 Replace the memory module slot cover and secure it using the screws. 5 Re-insert the main battery. For more information on inserting the main battery, see "Inserting a charged battery" on page 42. 6 Turn the computer right side up. 7 Reconnect the cables. 8 Restart the computer.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
31
Adding memory (optional)
15
Re-insert the main battery. For more information on inserting
the main battery, see “Inserting a charged battery” on page 42.
16
Turn the computer right side up.
17
Reconnect the cables.
18
Restart the computer.
TECHNICAL NOTE: You must have at least one memory module
installed for the computer to work.
Removing a memory module
If you need to remove a memory module:
1
Complete steps 1–8 in “Installing a memory module” on
page 27 to shut down the computer and open the memory
module slot cover.
Do not try to remove a memory module with the computer turned on.
You can damage the computer and the memory module.
Do not remove the memory module while the computer is in Standby
or Hibernation mode. The computer could hang up the next time you
turn it on and data in memory will be lost. In either of the above
cases, the Standby configuration will not be saved.
The following message appears when you turn on the power:
Warning: Resume Failure
Press Any Key to Continue
If the computer hangs up when you turn it on, perform the following:
Press the power button and hold it down for at least ten seconds,
then turn the power on again.
2
Pull the latches away from the memory module.
The memory module pops up slightly.
3
Gently lift the memory module to a 30-degree angle and slide it
out of the slot.
4
Replace the memory module slot cover and secure it using the
screws.
5
Re-insert the main battery. For more information on inserting
the main battery, see “Inserting a charged battery” on page 42.
6
Turn the computer right side up.
7
Reconnect the cables.
8
Restart the computer.