Toshiba Satellite P105-S6134 User Guide 2 - Page 7

Installing the IR receiver

Get Toshiba Satellite P105-S6134 PDF manuals and user guides View all Toshiba Satellite P105-S6134 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Toshiba USB TV Tuner Quick Guide 7 Installing the IR receiver 1 Place the USB IR receiver in a convenient location. Consider the following: ❖ The remote works within a distance of approximately 23 feet (7 meters). There should be an unobstructed line-of-sight from the remote control to the receiver. ❖ Avoid placing the receiver where it will be subject to intense heat or intense light. ❖ The USB cable is approximately 10 feet (3 meters) long. Be sure the receiver is within this distance from your MCE notebook computer. ❖ The IR transceiver cable is approximately 16 feet (5 meters) long. Be sure your set-top box (if used as the input to your MCE notebook computer) is within that distance from the IR receiver unit (which controls the set-top box via the IR transceiver). Skip step 2 if you are not using a set-top box (that is IR-controlled) as the signal source to your MCE notebook computer. 2 If you are connecting a set-top box, follow these directions to set up the IR transceiver (emitter) cable: ❖ Connect the IR transceiver cable to the back of the IR receiver unit. Use the connector port marked "1" if you have only one set-top box. ❖ Locate the remote control (IR) sensor window on your set-top box. This window is usually located at the front of the equipment. Refer to the manual that comes with your set-top box if needed. ❖ Remove the paper sticker from the red plastic emitter LED of the IR transceiver. Place the sticky side of the emitter LED directly on the set-top box IR sensor window. Do not totally block the window, since that may prevent you from using the IR remote that comes with the set-top box.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
Toshiba USB TV Tuner Quick Guide
7
Installing the IR receiver
1
Place the USB IR receiver in a convenient location. Consider
the following:
❖
The remote works within a distance of approximately 23
feet (7 meters). There should be an unobstructed
line-of-sight from the remote control to the receiver.
❖
Avoid placing the receiver where it will be subject to
intense heat or intense light.
❖
The USB cable is approximately 10 feet (3 meters) long.
Be sure the receiver is within this distance from your
MCE notebook computer.
❖
The IR transceiver cable is approximately 16 feet (5
meters) long. Be sure your set-top box (if used as the input
to your MCE notebook computer) is within that distance
from the IR receiver unit (which controls the set-top box
via the IR transceiver).
Skip step 2 if you are not using a set-top box (that is IR-controlled) as the
signal source to your MCE notebook computer.
2
If you are connecting a set-top box, follow these directions to
set up the IR transceiver (emitter) cable:
❖
Connect the IR transceiver cable to the back of the IR
receiver unit. Use the connector port marked "1" if you
have only one set-top box.
❖
Locate the remote control (IR) sensor window on your
set-top box. This window is usually located at the front of
the equipment. Refer to the manual that comes with your
set-top box if needed.
❖
Remove the paper sticker from the red plastic emitter
LED of the IR transceiver. Place the sticky side of the
emitter LED directly on the set-top box IR sensor window.
Do not totally block the window, since that may prevent
you from using the IR remote that comes with the set-top
box.