Toshiba TLP-260 Owners Manual - Page 61

Maintenance, Trouble indications

Get Toshiba TLP-260 PDF manuals and user guides View all Toshiba TLP-260 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Trouble indications If there is some problem inside the projector, the indicators light up or blink. Indicators ON LAMP ON / STANDBY TEMP FAN MENU ENTER VOL / ADJ EXIT AUTO SET Control panel (Main unit side) INPUT Maintenance KEYSTONE CONTENTS 61 ON LAMP TEMP FAN (Off) Or (Lit in red) The power does not come on. → Malfunction of the unit. • Unplug the power cord and call the dealer. ON LAMP (Lit in red) (Lit in red) TEMP FAN The lamp turns off or does not light up. → The projector will return to the standby mode in about 2 minutes. If the projector does not operate normally when the power is switched on again, the lamp is at the end of its life duration or the unit has a fault. • Lamp's life duration is over, replace the lamp with a new one. 65 • Unplug the power cord and call the dealer. ON LAMP (Lit in red) TEMP FAN (Lit in red) The power turns off or does not come on. → The inside is too hot, or the projector has been working in an area of high (Lit in green) temperature. Or (Lit in orange) • Place the projector correctly so the intake and exhaust fan's holes are not covered. • Turn the projector off, and leave it for a while, and turn it on again. Or • Clean the air filter. 62 (Lit in green) Or (off) * The icon appears before the power turned off. * The projector returns to the standby mode after the fault display has been shown for about 2 minutes. ON LAMP (Lit in red) TEMP FAN The power turns off or does not come on. → Trouble with the cooling fan. (Lit or flashing in red) • Unplug the power cord and call the dealer. Or (Lit or flashing in orange) * The icon appears before the power turned off. * The projector returns to the standby mode after the fault display has been shown for about 2 minutes. ON LAMP TEMP FAN The power turns off or does not come on. → The lamp cover is not properly attached. (Lit in red) (Flashing in orange) • Unplug the power cord and reattach the lamp cover. 66 * The icon appears before the power turned off. * The projector returns to the standby mode after the fault display has been shown for about 2 minutes. Notes • If abnormality occurs while operating, unplug the power cord. • When reinserting the power cord before the lamp has cooled, please wait until the lamp has cooled sufficiently before use. When the lamp is at a high temperature, it may not light and the life duration will be shortened.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
61
Maintenance
CONTENTS
If there is some problem inside the projector,
the indicators light up or blink.
Trouble indications
Indicators
Or
(Lit in red)
(Off)
ON
LAMP
TEMP
FAN
(Lit in red)
(Lit in red)
ON
LAMP
TEMP
FAN
(Flashing
in orange)
ON
LAMP
TEMP
FAN
(Lit in red)
ON
LAMP
TEMP
FAN
(Lit in red)
Or
(Lit or flashing
in red)
(Lit or flashing
in orange)
Or
Or
Or
(Lit in red)
(Lit in red)
(Lit in green)
(Lit in green)
(Lit in orange)
ON
LAMP
TEMP
FAN
(off)
The power does not come on.
→
Malfunction of the unit.
• Unplug the power cord and call the dealer.
The lamp turns off or does not light up.
→
The projector will return to the standby mode in about 2 minutes.
If the projector does not operate normally when the power is switched on again,
the lamp is at the end of its life duration or the unit has a fault.
• Lamp's life duration is over, replace the lamp with a new one.
• Unplug the power cord and call the dealer.
The power turns off or does not come on.
→
The inside is too hot, or the projector has been working in an area of high
temperature.
• Place the projector correctly so the intake and exhaust fan's holes are not covered.
• Turn the projector off, and leave it for a while, and turn it on again.
• Clean the air filter.
* The
icon appears before the power turned off.
* The projector returns to the standby mode after the fault display has been shown
for about 2 minutes.
The power turns off or does not come on.
→
Trouble with the cooling fan.
• Unplug the power cord and call the dealer.
* The
icon appears before the power turned off.
* The projector returns to the standby mode after the fault display has been shown
for about 2 minutes.
The power turns off or does not come on.
→
The lamp cover is not properly attached.
• Unplug the power cord and reattach the lamp cover.
* The
icon appears before the power turned off.
* The projector returns to the standby mode after the fault display has been shown
for about 2 minutes.
65
62
66
K
E
Y
S
T
O
N
E
A
U
T
O
S
E
T
E
X
I
T
ON / STANDBY
VOL / ADJ
E
N
T
E
R
M
E
N
U
I
N
P
U
T
F
A
N
T
E
M
P
L
A
M
P
O
N
Control panel
(Main unit side)
Notes
•
If abnormality occurs while operating, unplug the power cord.
•
When reinserting the power cord before the lamp has cooled, please wait until the lamp has
cooled sufficiently before use. When the lamp is at a high temperature, it may not light and the
life duration will be shortened.