Tripp Lite OMNISMART350HG Owner's Manual for SmartPro and OmniSmart Medical-Gr - Page 6

Indicator Lights - power supply

Get Tripp Lite OMNISMART350HG PDF manuals and user guides View all Tripp Lite OMNISMART350HG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Basic Operation continued For All Models-"MUTE/TEST" Button: To Silence (or "Mute") UPS Alarms: briefly press and release the MUTE/TEST button.* To Run a Self-Test: with your UPS plugged in and turned ON, press and hold the MUTE/TEST button for two seconds.* Continue holding the button until the alarm beeps several times and the UPS performs a self test. See "Results of a Self-Test" below. Note: you can leave connected equipment on during a self-test. Your UPS, however, will not perform a self-test if it is not turned ON (see "POWER" Button description). CAUTION! Do not unplug your UPS to test its batteries. This will remove safe electrical grounding and may introduce a damaging surge into your network connections. Results of a Self-Test: The test will last approximately 10 seconds as the UPS switches to battery to test its load capacity and battery charge.** If the "OUTPUT LOAD LEVEL" LED remains lit red and the alarm continues to sound after the test, the UPS's outlets are overloaded. To clear the overload, unplug some of your equipment and run the self-test repeatedly until the "OUTPUT LOAD LEVEL" LED is no longer lit red and the alarm is no longer sounding. CAUTION! Any overload that is not corrected by the user immediately following a self-test may cause the UPS to shutdown and cease supplying output power in the event of a blackout or severe brownout. If the "BATTERY WARNING" LED remains lit and the alarm continues to sound after the test, the UPS batteries need to be recharged or replaced. Allow the UPS to recharge continuously for 12 hours, and repeat the self-test. If the LED remains lit, contact Tripp Lite for service. If your UPS requires battery replacement, visit www.tripplite.com/support/battery/index.cfm to locate the specific Tripp Lite replacement battery for your UPS. * The alarm will beep once briefly after the indicated interval has passed. ** SmartPro models' operation during the self-test: the "POWER" LED will be flashing and the "OUTPUT LOAD LEVEL" and "BATTERY CHARGE" LEDs will be lit and the UPS alarm will sound. OmniSmart models' operation during the self-test: all LEDs will be lit and the UPS alarm will sound. Indicator Lights All Indicator Light descriptions apply when the UPS is plugged into an AC outlet and turned on. "POWER" LED For SmartPro Models Only: this green LED lights continuously when the UPS is ON and supplying connected equipment with AC power from a utility source. The LED flashes and an alarm sounds (4 short beeps followed by a pause) to indicate the UPS is operating from its internal batteries during a blackout or severe brownout. If the blackout or severe brownout is prolonged, you should save files and shut down your equipment since internal battery power will eventually be depleted. See "BATTERY CHARGE" LED description below. For OmniSmart Models Only: this green light will turn ON whenever your UPS is receiving normal AC line power. It will flash while the UPS is in CHARGE ONLY mode to indicate that the UPS will not provide battery backup during a blackout or brownout. 6 200903087 93-2890.indb 6 3/26/2009 4:56:29 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
All Indicator Light descriptions apply when the UPS is plugged into an AC outlet and turned
on.
“POWER” LED
For SmartPro Models Only:
this green LED lights continuously when the
UPS is ON and supplying connected equipment with AC power from a utility
source. The LED flashes and an alarm sounds (4 short beeps followed by a
pause) to indicate the UPS is operating from its internal batteries during a
blackout or severe brownout. If the blackout or severe brownout is prolonged,
you should save files and shut down your equipment since internal battery
power will eventually be depleted. See “BATTERY CHARGE” LED descrip-
tion below.
For OmniSmart Models Only:
this green light will turn ON whenever your
UPS is receiving normal AC line power. It will flash while the UPS is in
CHARGE ONLY mode to indicate that the UPS will not provide battery
backup during a blackout or brownout.
6
For All Models—“MUTE/TEST” Button:
To Silence (or “Mute”) UPS Alarms:
briefly press and release the MUTE/TEST
button.*
To Run a Self-Test:
with your UPS plugged in and turned ON, press and
hold the
MUTE/TEST button for two seconds.* Continue holding the button until the alarm
beeps several times and the UPS performs a self test. See “Results of a Self-Test”
below. Note: you can leave connected equipment on during a self-test. Your UPS,
however, will not perform a self-test if it is not turned ON (see "POWER" Button
description).
CAUTION! Do not unplug your UPS to test its batteries. This will remove safe
electrical grounding and may introduce a damaging surge into your network
connections.
Results of a Self-Test:
The test will last approximately 10 seconds as the UPS
switches to battery to test its load capacity and battery charge.**
If the “OUTPUT LOAD LEVEL” LED remains lit red and the alarm contin-
ues to sound after the test, the UPS’s outlets are overloaded. To clear the
overload, unplug some of your equipment and run the self-test repeatedly until
the “OUTPUT LOAD LEVEL” LED is no longer lit red and the alarm is no
longer sounding.
CAUTION! Any overload that is not corrected by the user immediately
following a self-test may cause the UPS to shutdown and cease supplying
output power in the event of a blackout or severe brownout.
If the “BATTERY WARNING” LED remains lit and the alarm continues to sound
after the test, the UPS batteries need to be recharged or replaced. Allow the
UPS to recharge continuously for 12 hours, and repeat the self-test. If the LED
remains lit, contact Tripp Lite for service
.
If your UPS requires battery replace-
ment, visit www.tripplite.com/support/battery/index.cfm to locate the specific
Tripp Lite replacement battery for your UPS.
* The alarm will beep once briefly after the indicated interval has passed. ** SmartPro models’
operation during the self-test: the “POWER” LED will be flashing and the “OUTPUT LOAD
LEVEL” and “BATTERY CHARGE” LEDs will be lit and the UPS alarm will sound. OmniSmart
models’ operation during the self-test: all LEDs will be lit and the UPS alarm will sound.
Basic Operation
continued
Indicator Lights
200903087
93-2890.indb
6
3/26/2009
4:56:29 PM