Tripp Lite SRW12US Owner's Manual 12U Wallmount Rack Enclosures 933117 - Page 4

Enclosure Installation, Enclosure Configuration - depth

Get Tripp Lite SRW12US PDF manuals and user guides View all Tripp Lite SRW12US manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

4. Enclosure Installation (continued) 4.4 Ground Connection All parts of the enclosure are grounded to the frame of the enclosure. Use the enclosure's front or rear threaded grounding point A and an M6 screw (included) to connect the frame of the enclosure directly to your facility's earth ground connection with an 8 AWG (3.264 mm) wire. Route A the ground wire under the enclosure's frame to ensure unhindered door operation. Warning: Attach each enclosure to earth ground separately. Do not use the enclosure without an earth ground connection. EARTH GROUND 5. Enclosure Configuration Before installation, be sure to plan the location and arrangement of components within the enclosure. Be sure all mounting rails are reversed or adjusted for depth, depending on your equipment configuration. 5.1 Door Locks The front and back doors have locks that are accessible by the included keys. Each side panel locks using an L-shaped lever on the inside of the enclosure. 1 To unlock and remove the side panels, lift the shorter leg of the "L" up (labeled A ) and pull it away from the side panel (labeled B ). Pull the tab on the side panel and remove it from the enclosure. 2 To re-lock the side panels, secure it in the proper position, lift the shorter leg of the "L" up (labeled A ) and push it toward the side panel, back into the hole that it was in initially (labeled B ). Once it is in place, push the shorter leg of the "L" down to lock it. Note: To lock and unlock the side panels, you will need to have access to the interior of the enclosure. A B A 1 5.2 Cable Access and Management The back door of the enclosure has a square opening for cable access and management. An additonal opening can be found on top of the main cabinet. Each opening can also be closed by screwing in the removeable cable access panels. B 2 5.3 Reversing the Enclosure In order to accommodate various rack configurations, the enclosure can be reversed. To do so, simply turn the enclosure over so that the doors open in the opposite direction. 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
4
4. Enclosure Installation
(
continued
)
5. Enclosure Configuration
4.4 Ground Connection
5.1 Door Locks
5.2 Cable Access and Management
All parts of the enclosure are grounded to the frame of the enclosure. Use the enclosure’s front or
rear threaded grounding point
A
and an M6 screw (included) to connect the frame of the
enclosure directly to your facility’s earth ground connection with an 8 AWG (3.264 mm) wire. Route
the ground wire under the enclosure’s frame to ensure unhindered door operation.
Warning:
Attach each enclosure to earth ground separately. Do not use the enclosure without an
earth ground connection.
The front and back doors have locks that are accessible by the included keys.
Each side panel locks using an L-shaped lever on the inside of the enclosure.
1
To unlock and remove the side panels, lift the shorter leg of the “L” up (labeled
A
) and pull it away from the side panel (labeled
B
). Pull the tab
on the side panel and remove it from the enclosure.
2
To re-lock the side panels, secure it in the proper position, lift the shorter leg of the “L” up (labeled
A
) and push it toward the side panel, back
into the hole that it was in initially (labeled
B
). Once it is in place, push the shorter leg of the “L” down to lock it.
Note
: To lock and unlock the
side panels, you will need to have access to the interior of the enclosure.
The back door of the enclosure has a square opening for cable access and management. An
additonal opening can be found on top of the main cabinet. Each opening can also be closed by
screwing in the removeable cable access panels.
Before installation, be sure to plan the location and arrangement of components within the enclosure. Be sure all mounting rails are reversed or
adjusted for depth, depending on your equipment configuration.
5.3 Reversing the Enclosure
In order to accommodate various rack configurations, the enclosure can be reversed. To do so, simply turn the enclosure over so that the doors open
in the opposite direction.
EARTH
GROUND
A
1
2
A
B
A
B