Tripp Lite SU3000RTXL2U Owner's Manual for SmartOnline UPS 932835 - Page 3

Installation - tripp lite

Get Tripp Lite SU3000RTXL2U PDF manuals and user guides View all Tripp Lite SU3000RTXL2U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

2. Installation 2.1 Mounting (Rack) • Use the included rackmount shelves and mounting hardware to mount the UPS system in a 4-post rack or rack enclosure. To mount the UPS system in a 2-post (telecom) rack, order Tripp Lite's 2-Post Rackmount Kit (model 2POSTRMKITWM, sold separately). • The instructions in this manual are for common rack and rack enclosure types and may not be appropriate for all mounting applications. The user must determine the fitness of hardware and procedures before mounting. If hardware or procedures are not suitable for the application, contact the manufacturer of the rack or rack enclosure for a solution. Warning: The UPS system is very heavy-be careful when moving or lifting it. 4-Post Mounting Procedure 1 The included plastic pegs A will support the empty rackmount shelves B until the permanent mounting hardware is installed. Insert a peg near the center of the front and rear bracket of each shelf as shown. (Each front bracket has 6 holes and each rear bracket has 3 holes.) The pegs will snap into place. After installing the pegs, expand each shelf to match the depth of the vertical rack rails. The pegs will fit through the square holes in the rack rails to support the shelves. Confirm that the shelves are level in all directions. Note: The support ledge of each shelf must face inward. 2 Secure the shelves B to the rack rails permanently using the longer included screws and washers C as shown. (Place 4 screws at the front and 4 screws at the back.) Tighten all screws before proceeding. B A 1 B C 2 D Warning: Do not attempt to install the UPS system until the required screws have been inserted and E tightened. The plastic pegs will not support the weight of the UPS system. 3 3 Attach the mounting brackets D to the forward mounting holes of the UPS system using the shorter included screws E . The mounting bracket F ears must face forward. 4 With the aid of an assistant, lift the UPS system and slide it onto the mounting shelves. Insert 4 of the included screws F through the mounting bracket ears and into the vertical rack rails. Tighten all screws securely. 4 F A B C B D E 3 201102140 932835.indb 3 3/29/2011 4:50:11 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
3
2. Installation
1
The included plastic pegs
A
will support the empty
rackmount shelves
B
until the permanent mounting
hardware is installed. Insert a peg near the center of
the front and rear bracket of each shelf as shown.
(Each front bracket has 6 holes and each rear
bracket has 3 holes.) The pegs will snap into place.
After installing the pegs, expand each shelf to
match the depth of the vertical rack rails. The pegs
will fit through the square holes in the rack rails to
support the shelves. Confirm that the shelves are
level in all directions.
Note: The support ledge of
each shelf must face inward.
2
Secure the shelves
B
to the rack rails permanently
using the longer included screws and washers
C
as
shown. (Place 4 screws at the front and 4 screws at
the back.) Tighten all screws before proceeding.
Warning: Do not attempt to install the UPS system
until the required screws have been inserted and
tightened. The plastic pegs will not support the
weight of the UPS system.
3
Attach the mounting brackets
D
to the forward
mounting holes of the UPS system using the
shorter included screws
E
. The mounting bracket
ears must face forward.
4
With the aid of an assistant, lift the UPS system
and slide it onto the mounting shelves. Insert 4 of
the included screws
F
through the mounting
bracket ears and into the vertical rack rails. Tighten
all screws securely.
•
Use the included rackmount shelves and mounting hardware to mount the UPS system in a 4-post
rack or rack enclosure. To mount the UPS system in a 2-post (telecom) rack, order Tripp Lite’s 2-Post
Rackmount Kit (model 2POSTRMKITWM, sold separately).
•
The instructions in this manual are for common rack and rack enclosure types and may not be
appropriate for all mounting applications. The user must determine the fitness of hardware and
procedures before mounting. If hardware or procedures are not suitable for the application, contact the
manufacturer of the rack or rack enclosure for a solution.
Warning: The UPS system is very
heavy—be careful when moving or lifting it.
4-Post Mounting Procedure
1
2
3
D
D
E
E
4
F
F
2.1 Mounting (Rack)
C
B
C
B
A
B
B
A
201102140 932835.indb
3
3/29/2011
4:50:11 PM