URC Vivido-Dimmers Battery Operated Switch Manual - Page 1

Battery Operated Switch A Step-by-Step Guide for VInLs-t9Ea5Nl0li0Gn-gBLOIaSnSdH-XOUpseerartGinugidtehe Battery Operated Switch ON/OFF BUTTON DIMMER BUTTON Decorater Look The VL-9500-BOS-X is a battery-operated wireless device that operates as an accessory in a Z-Wave network. It will control associated dimmers or switches and their lighting loads. You can create a 3-way where a second location is not currently available without having to add new electrical wiring. This product works with other Z-Wave products from different vendors and product categories as part of the same network. This product is not a listening node as it is a battery powered device and goes to sleep to conserve battery life. Therefore it will not perform the repeater function typical of other Z-Wave devices. OPEN Lift Latch to Open Battery Cover Plastic Tabs x 4 is expected to be 1-2 years. BATTERY INSTALLATION AND REPLACEMENT: 2 CR2025 batteries are included with each VL-9500-BOS-X. Lift the battery latch with a screwdriver to open the battery cover. Remove the plastic strips from under the batteries. Observe polarity when installing the batteries. Be careful to insert the batteries under the 4 small plastic tabs in the battery compartment. Re-latch the battery cover. After the batteries are successfully installed, the LED on the VL-9500-BOS-X will blink for one minute to indicate the device in not included in the RF network. The device will go to sleep after one minute to conserve battery life. When not installed, pressing the ON/OFF button again will wake up the device, and the LED will resume blinking for one minute to remind the installer that the device is still not installed in the RF network. With normal usage (up to 20 keypresses per day) battery life PHYSICAL INSTALLATION INSTRUCTIONS: Attach the VL-9500-BOS-X to any flat surface using the double-sided tape provided, or mount it to the wall using the screws and anchors provided. NOTE: Do not install an VL-9500-BOS-X over an electrical box. The device must be installed onto a flat surface. Do not install on a metal surface since this will impede the RF signal. Z-WAVE NETWORK INSTALLATION INSTRUCTIONS: The VL-9500-BOS-X can be used as an accessory device which can be included in a new or existing network by using your Z-Wave controller. To include as an accessory device, select the command on your controller for inclusion (Install, Add Device, Add Node, Include Device, etc.), then press the VL-9500-BOS-X on/off button one time to include it in the network. The LED will blink a few times and then stop blinking after the device is successfully included in the network. After inclusion in a network, the VL-9500-BOS-X can then be associated with and control up to 5 other hard-wired RF devices at one time. During the association process, your Z-Wave controller may prompt you to wake up the VL-9500-BOS-X, which will then allow the association process to occur. To wake the VL-9500-BOS-X press the dim down or up button once. (For detailed instructions refer to your controller manual.) To exclude this device from a Z-Wave network, select the command on your Z-Wave controller for exclusion (Uninstall, Remove Device, Remove Node, Exclude Device, etc.), then press the on/off button one time to exclude it from the network. The LED will start blinking rapidly and then blink slowly about 10 times. OPERATING INSTRUCTIONS: • The blue LED indicator is normally OFF. • The blue LED indicator will blink once when turning a device OFF. • The blue LED indicator will come on for 2 seconds and then turn OFF when turning a device ON. • The ON/OFF switch on the VL-9500-BOS-X will turn the load ON/OFF when associated with Z-Wave RF switches. • The ON/OFF switch on the VL-9500-BOS-X will turn a receptacle ON/OFF when associated with Z-Wave RF receptacles. • The ON/OFF switch on the VL-9500-BOS-X will turn the light ON/OFF when associated with a Z-Wave RF Master Dimmer. • The UP/DOWN dimmer buttons will control the light level when associated with a Z-Wave RF Master Dimmer. BUTTON FUNCTIONS REFERENCE FOR THE VL-9500-BOS-X: On/Off - Press the On/Off button once. The installed devices will turn on or off depending on their previous state. If no devices are installed in the network, the LED will blink rapidly for about 3 seconds. This will also happen if the VL-9500-BOS-X cannot reach the devices for any reason. Possible reasons might be the devices are not powered, perhaps due to a tripped circuit breaker, or if the VL-9500-BOS-X cannot reach the devices due to poor RF conditions such as low signal strength. Dimming - Pressing and holding the dimming button will cause installed dimmer devices to raise or lower the ES dimming level. Releasing the button will stop this action. Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1: This device may not cause harmful interference, and 2: This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. FCC CAUTION: Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. Universal Remote Control, Inc. 500 Mamaroneck Ave. Harrison, NY 10528 (914) 835-4484 [email protected] www.UniversalRemote.com IS-0117-U-EN (REV. A)