Uniden BC340CRS English Owners Manual - Page 13

VOLUME Control, SQUELCH Control, ALARM Select, Radio, SNOOZE/Backlight, TIME Set, Alarm Set, Clock - just squelched

Get Uniden BC340CRS PDF manuals and user guides
UPC - 050633650462
View all Uniden BC340CRS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

1 VOLUME Control - lets you raise or lower the level of the sound. 2 SQUELCH Control - lets you set the signal level required to receive a transmission. If you open the squelch all the way, you will hear hissing between transmissions. This lets you hear weak signals, but prevents scanning. As you close squelch, a stronger signal is required to stop scanning and open audio. You normally set the control to a point just where hissing on all channels stops between transmissions. 3 SCAN - press to begin scanning the channels or to resume scanning. 4 ALARM Select - Set to Off to disable alarm; Set to Radio to enable the radio alarm; Set to Tone to enable the tone alarm. 5 SNOOZE/Backlight - Backlight: Tap to turn the LCD backlight on for 15 seconds. Press and hold to permanently turn on the backlight. Press and hold again to turn off the backlight. Snooze: Press while the alarm sounds to silence the alarm for 5 minutes. 6 TIME Set - Use to select your desired operation: Alarm Set; Clock Set; Clock. 7 HOLD - press to temporarily stop scanning, limit searching, or weather scanning and remain on the channel. The scanner displays the channel on hold. Press again to resume searching or scanning. 8 E/PGM - Press to enter the Program Mode. In Program Mode, enter the desired frequency using the numeric keys. Then press E/PGM to store that frequency into the memory. In Limit Search Mode, after entering the frequency, press E/PGM to program the upper and lower limit frequency. 9 0 to 9 - use the numeric keys in four basic operations: • press a numeric key to enter a frequency. • press a numeric key to change a channel using the Direct Channel Access feature. • press a numeric key while scanning to enable or disable the associated scanning bank memory bands. 10 POWER - Press to turn power on and off. The time displays when power is off (standby mode). 11 ./CLR - this key has three functions: • press to input a decimal point when you enter a frequency. • press to cancel a numeric key input − 0 to 9 • press to clear an error display. Introduction 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
13
Introduction
1
VOLUME Control
— lets you raise or lower the level of the sound.
2
SQUELCH Control
— lets you set the signal level required to receive a
transmission. If you open the squelch all the way, you will hear hissing
between transmissions. This lets you hear weak signals, but prevents
scanning. As you close squelch, a stronger signal is required to stop scanning
and open audio. You normally set the control to a point just where hissing on
all channels stops between transmissions.
3
SCAN
— press to begin scanning the channels or to resume scanning.
4
ALARM Select
— Set to
Off
to disable alarm; Set to
Radio
to enable the
radio alarm; Set to
Tone
to enable the tone alarm.
5
SNOOZE/Backlight
— Backlight: Tap to turn the LCD backlight on for 15
seconds. Press and hold to permanently turn on the backlight. Press and hold
again to turn off the backlight.
Snooze: Press while the alarm sounds to silence the alarm for 5 minutes.
6
TIME Set
— Use to select your desired operation:
Alarm Set
;
Clock Set
;
Clock
.
7
HOLD
— press to temporarily stop scanning, limit searching, or weather
scanning and remain on the channel. The scanner displays the channel on
hold. Press again to resume searching or scanning.
8
E/PGM
— Press to enter the
Program Mode
. In Program Mode, enter the
desired frequency using the numeric keys. Then press
E/PGM
to store that
frequency into the memory.
In
Limit Search Mode
, after entering the frequency, press
E/PGM
to program
the upper and lower limit frequency.
9
0 to 9
— use the numeric keys in four basic operations:
•
press a numeric key to enter a frequency.
•
press a numeric key to change a channel using the Direct Channel Access
feature.
•
press a numeric key while scanning to enable or disable the associated
scanning bank memory bands.
10 POWER
— Press to turn power on and off. The time displays when power is
off (standby mode).
11 ./CLR
— this key has three functions:
•
press to input a decimal point when you enter a frequency.
•
press to cancel a numeric key input
−
0
to
9
•
press to clear an error display.