Uniden DCT748-2 English Owners Manual

Uniden DCT748-2 Manual

Get Uniden DCT748-2 PDF manuals and user guides View all Uniden DCT748-2 manuals
Add to My Manuals
Save this manual to your list of manuals

Uniden DCT748-2 manual content summary:

  • Uniden DCT748-2 | English Owners Manual - Page 1
    DCT 748 SERIES OWNER'S MANUAL
  • Uniden DCT748-2 | English Owners Manual - Page 2
    Telephone Answering Device 48 48 7 Turning the Answering System On/Off 52 Setting up the Phone 7 Setting Your Outgoing Message (Greeting) 52 Expanding Your Phone 12 Using Your Answering System 54 Register the Handset 14 Remote Operation 58 Changing the Digital Security Code 15 MULTI
  • Uniden DCT748-2 | English Owners Manual - Page 3
    line, it can support up to four handsets. You can now place a fully-featured cordless handset anywhere in your home or office where AC power is available to connect the handset chargers. Extra handsets also allow you to establish a three-way conference call among two handsets and an outside line
  • Uniden DCT748-2 | English Owners Manual - Page 4
    interference from other cordless phones. IntegriSound Built in sound quality which provides life-like conversations. With DirectLink mode, you can use two or more handsets as radio transceivers (walkie-talkies). Be sure to visit our web site: www.uniden.com Uniden is a registered trademark
  • Uniden DCT748-2 | English Owners Manual - Page 5
    2 7 3 4 8 9 10 5 11 12 13 Repeat Delete www.uniden.com Play Skip Stop 1.Handset Antenna 2.Headset Jack Cover 3.Beltclip Hole 4.Speakerphone Speaker and Ringer 5.Handset Battery Compartment 6.New Message LED 7.Handset Earpiece 8.LCD Display 9. (ring)/vol (volume) and ∧/∨ (P. 30 & 17
  • Uniden DCT748-2 | English Owners Manual - Page 6
    32 33 34 23. Base Speaker 24. charge LED 25. in use LED 26. Base antenna 27. New Message LED 28. (play/stop) (p.54) 29. find hs / (skip) (p.34 & 55) 30. (repeat LED (p.58) 34. Base Charging Contacts 35. TEL LINE Jack 36. DC IN 9V Jack [5] CONTROLS & FUNCTIONS www.uniden.com CONTROLS & FUNCTIONS
  • Uniden DCT748-2 | English Owners Manual - Page 7
    This icon cycles depending on the battery status (full, medium, low, and empty). 4 Standby Talk Talk Talk Talk Talk Ringer off icon indicates that ringer is turned off. Mute icon appears when you mute the handset. Speaker icon appears when the handset speaker phone is used. Booster icon appears
  • Uniden DCT748-2 | English Owners Manual - Page 8
    your home has specially wired alarm equipment connected to phone line, be sure that installing the system does not up the Phone Do the following steps: A. Choose the best location B. Install the rechargeable battery pack into the handset C. Connect the base unit and charge the handset D. Mount
  • Uniden DCT748-2 | English Owners Manual - Page 9
    place. 4) Place the battery case cover back on the handset and slide it upwards until it clicks into place. note •Use only the Uniden (BT-446) rechargeable battery pack supplied with your cordless telephone. •Replacement battery packs are also available through the Uniden Parts Department at (800
  • Uniden DCT748-2 | English Owners Manual - Page 10
    hours before plugging into the phone line. 5) Once the handset battery pack is fully charged, connect the telephone line cords to the TEL LINE jack and to a telephone outlets. If your telephone outlet isn't modular, contact your telephone company for assistance. [9] GETTING STARTED www.uniden.com
  • Uniden DCT748-2 | English Owners Manual - Page 11
    Base Unit on a Wall Standard wall plate mounting This phone can be mounted on any standard wall plate. 1) Plug into a standard 120V AC wall outlet. 3) Plug the telephone line cords into the TEL LINE jack. 4) Plug the telephone line cords into the telephone outlets. 5) Align the mounting slots on the
  • Uniden DCT748-2 | English Owners Manual - Page 12
    plate, you can mount your phone directly to the wall. Before phone within 5 feet of a working phone jack to avoid excessive lengths. • Make sure the wall material is capable of supporting the weight of the base and handset mounting the phone. 2) Refer to steps 1 through 5 on page 10
  • Uniden DCT748-2 | English Owners Manual - Page 13
    incoming calls. It is possible to have a three-way conference among two handsets and an outside lines. All of the handsets ring when a call is received. Backward / Forward Compatibility Your phone may be compatible with other Uniden 2.4 GHz Digital Expandable Systems. Please visit our website at www
  • Uniden DCT748-2 | English Owners Manual - Page 14
    the expansion handset's charger The handset is powered by a rechargeable battery pack. The battery recharges automatically when the handset is placed handset makes good contact with the base charging contacts. 4) Charge the handset battery pack for at least 15-20 hours before using your new cordless
  • Uniden DCT748-2 | English Owners Manual - Page 15
    been registered display Models vary! Charge handset on the base for registration or refer to Owner's Manual. When you register an extra handset to the base, the handset ID will be assigned. For the DCX700 expansion handset 1) Before registering the extra handset, the battery pack MUST be charged
  • Uniden DCT748-2 | English Owners Manual - Page 16
    the code is not necessary. In the rare situation that you suspect another cordless telephone is using the same security code, you can change the code. To change the digital security code: 1. Perform the "System Reset" options ("De-register the Handset" and "Replacing the Base Setting") for all the
  • Uniden DCT748-2 | English Owners Manual - Page 17
    advantage of all the phone features. The table Handset one minute Off English On On SUN 12:00 AM CIDCW on/CWDX off None Tone note For Global Setup and System Reset, when setting options from the handset, make sure the line is not in use and the handsets are within range of the base. www.uniden
  • Uniden DCT748-2 | English Owners Manual - Page 18
    Using the interface Below are some tips for using the software interface on your phone. • Press menu/clear to access the main menu. • Use /vol *CPFUGV5GVWR menu. • If you do not press a key within 30 seconds, the phone will time out and exit the menu mode. When setting Day and Time, the time-
  • Uniden DCT748-2 | English Owners Manual - Page 19
    Light Bug, Beep Boop, Tone Board, Chip Chop, Party Clap, Reminder) 1) Press menu/clear. Select the Handset Setup menu, and then the Ringer Tones submenu. 2) Press /vol/∧ or /vol/∨ to move the pointer. You select/ /audio tone. You will hear a confirmation tone. www.uniden.com GETTING STARTED [18]
  • Uniden DCT748-2 | English Owners Manual - Page 20
    entries, the phone uses the distinctive 1) Press menu/clear. Select the Handset Setup menu, and then the Distinctive AutoTalk allows you to answer the phone simply by removing the handset from the cradle. You do call. 1) Press menu/clear. Select the Handset Setup menu, and then the AutoTalk submenu
  • Uniden DCT748-2 | English Owners Manual - Page 21
    GETTING STARTED Setting Anykey Answer Anykey Answer allows you to answer the phone by pressing any number key, */tone/ or #/ on the handset. 1) Press menu/clear. Select the Handset Setup menu, and then the Anykey Answer submenu. 2) Press /vol/∧ or /vol/∨ to select On or Off. 3) Press select/ /
  • Uniden DCT748-2 | English Owners Manual - Page 22
    use. Choose from English, French, or Spanish. 1) Press menu/clear. Select the Handset Setup menu, and then the Language submenu. 2) Press /vol/∧ or /vol/∨ You can turn this tone on or off. 1) Press menu/clear. Select the Handset Setup menu, and then the Key Touch Tone submenu. 2) Press /vol/∧ or /
  • Uniden DCT748-2 | English Owners Manual - Page 23
    If you change one of the global settings, you change that setting for all registered handsets. Only one handset can change global settings at a time. Setting Day and Time Day & Time note If no key is pressed for two minutes, the phone will exit the menu mode. www.uniden.com GETTING STARTED [22]
  • Uniden DCT748-2 | English Owners Manual - Page 24
    the line. Call Waiting Deluxe (CWDX) allows you to handle call waiting calls in seven different ways. See page 44 for instructions on " option, your local area code does not appear in the Caller ID message. When calls are received from outside your local area code, you will STARTED www.uniden.com
  • Uniden DCT748-2 | English Owners Manual - Page 25
    default setting is tone dialing. Set the dialing mode to match the dialing system used by your local phone service. • If you are not sure of your dialing system, make a trial call. If the 2WNUG 3) Press select/ /audio tone. You will hear a confirmation tone. www.uniden.com GETTING STARTED [24]
  • Uniden DCT748-2 | English Owners Manual - Page 26
    Reset De-register the Handset 1) Press and hold end and #/ for more than 5 seconds. Select the Deregister HS submenu. 2) Press /vol/∧ or /vol/∨ to select the handset the handset displays Models vary! Charge handset on the base for registration or refer to Owner's Manual. Register the handset to
  • Uniden DCT748-2 | English Owners Manual - Page 27
    BASICS Using Your Phone Making and Receiving Calls note Making a call From the handset 1) Remove the handset from the charging cradle. 2) Press talk/flash. 3) Listen for the dial tone. 4) Dial the number. •If the line is already in use, the base and all registered handsets that are not currently
  • Uniden DCT748-2 | English Owners Manual - Page 28
    or to set "Anykey Answer" see page 20. Receiving a call 1) Remove the handset from the charging cradle. (If AutoTalk is on, the phone will automatically answer the call when you pick it up.) 2) Press talk/flash. OR If the handset is off the charging cradle, press talk/flash. If Any Key Answer is
  • Uniden DCT748-2 | English Owners Manual - Page 29
    press hold/transfer/int'com on the handset. The call will be put in hold. If read, Line On Hold. 2) To talk to the caller, press talk/flash or on a handset. The phone will service. •You can place a call on hold for 5 minutes. When 5 minutes has passed, the call is disconnected, and the phone
  • Uniden DCT748-2 | English Owners Manual - Page 30
    see page 38. Redialing a Call You can quickly redial the last three phone numbers from the handset. Redialing from Standby Mode 1) With the phone in standby mode, press pause/redial . 2) Press pause/redial or / / /audio tone or menu/clear. The redialed number is deleted. [29] BASICS www.uniden.com
  • Uniden DCT748-2 | English Owners Manual - Page 31
    current incoming call only. The ringer tone will return to the previous setting starting with the next incoming call. note You can only mute the handset ringer if the handset is off the base when the phone starts ringing. BASICS www.uniden.com BASICS [30]
  • Uniden DCT748-2 | English Owners Manual - Page 32
    , Natural Tone, is recommended for hearing aid users. •You can change the audio tone level Tones feature can not be used while using speaker phone. Mute Microphone You can temporarily mute the microphone 1) Press menu/clear during talk mode (while the phone is in use) to mute the microphone. 2)
  • Uniden DCT748-2 | English Owners Manual - Page 33
    telephone prescription refills, customer support menus, etc. If your phone is set to pulse phone automatically returns to pulse dialing mode. Traveling Out of Range During a call, as you begin to move your handset handset returns to standby mode. You may return to the call if you move your handset
  • Uniden DCT748-2 | English Owners Manual - Page 34
    phone, you can manually improve the sound by setting the Clarity Booster to on. This works only when the phone other registered handsets. This works only when the phone is in handset to join a call, exit privacy mode. Use the same procedure above. Privacy Mode Off appears. [33] BASICS www.uniden.com
  • Uniden DCT748-2 | English Owners Manual - Page 35
    the phone is in standby mode. All registered handsets beep for 60 seconds, and Paging appears on the handset display. To cancel paging, press any key on the handset or find hs/ on the base. note If the battery pack is completely drained, the handset will not beep. BASICS www.uniden.com BASICS
  • Uniden DCT748-2 | English Owners Manual - Page 36
    with just a few key presses. Phonebook memory is stored independently in the cordless handsets. You can store up to 100 numbers in each handset. The phone uses the same memory locations to store phonebook entries and Caller ID messages. Any empty phonebook locations are used to store Caller ID
  • Uniden DCT748-2 | English Owners Manual - Page 37
    . Press menu/clear to erase the wrong character, and then enter the correct character. To delete all characters press and hold menu/clear. PHONEBOOK www.uniden.com PHONEBOOK [36]
  • Uniden DCT748-2 | English Owners Manual - Page 38
    FKV0Q 6) Use the number keypad, */tone/ , or #/ to enter the phone number (up to 20 digits). To insert a 2- second pause in the dialing sequence store the number. 7) If you store the phonebook location from the handset, Distinctive Ring appears. Press /vol/∧ or /vol/∨ to move the .uniden.com
  • Uniden DCT748-2 | English Owners Manual - Page 39
    , follow the steps 4-9 in "Storing and Editing Phone Numbers, Names, Distinctive Rings and Speed Dial" on page 35. note •If a call comes in via a telephone system that does not offer Caller ID service, no information is stored. •If the Caller ID message was received as a private/unknown number, or
  • Uniden DCT748-2 | English Owners Manual - Page 40
    6 once. Press /vol/∧ or /vol/∨, until the phonebook location is displayed. 4) To finish the viewing operation, press end (or during a call). PHONEBOOK [39] PHONEBOOK www.uniden.com
  • Uniden DCT748-2 | English Owners Manual - Page 41
    the phone is in each handset. You must program a speed dial number before you can use the speed dialing feature. When the phone is in standby mode, press and hold a number key (0-9) associated with the speed dial until the phone number appears, and then press talk/flash or on the handset
  • Uniden DCT748-2 | English Owners Manual - Page 42
    Number, Distinctive Ring and Speed Dial 1) When the phone is in standby mode, press . To delete all phonebook locations editing the entry, follow the steps 4 to 9 under "Phonebook (Storing and Editing Phone Numbers, Names, Distinctive Rings, and Speed Dial)" on page 35 to complete the editing operation
  • Uniden DCT748-2 | English Owners Manual - Page 43
    handset to another without having to manually re-enter names and numbers. You can transfer one phonebook memory location at a time or all memory locations at once. 1) When the phone are full, the message will be stored in the phonebook. However, the oldest Caller ID message will be erased from
  • Uniden DCT748-2 | English Owners Manual - Page 44
    message is received, the display shows the caller's phone number along with the date and time. The incoming call information is stored in the Caller ID record. If the Caller ID service includes the caller's name, the name will appear in the display (up to 15 characters). [43] CALLER ID www.uniden
  • Uniden DCT748-2 | English Owners Manual - Page 45
    hold, send them to your voice mail service, or conference them into your current call. message states that user will be available shortly, and the call is place on hold. Tell Busy - A prerecorded message phone back to a call. To return back to a call, press talk/flash. www.uniden.com CALLER ID [44]
  • Uniden DCT748-2 | English Owners Manual - Page 46
    messages and phonebook locations (including Speed Dials) for each handset. You can view the Caller ID list through the handset during a call or when the phone The screen shows the number of new messages and total messages. 2) To view the Caller ID messages in historical order %CNNGT+& 0GY
  • Uniden DCT748-2 | English Owners Manual - Page 47
    during a call). Deleting Information from the Caller ID List 1) When the phone is in standby mode, view the Caller ID information to be deleted (see information cannot be retrieved Deleting all Caller ID name/numbers 1) When the phone is in standby mode, press cid. 2) Press menu/clear. Delete All
  • Uniden DCT748-2 | English Owners Manual - Page 48
    Party from the Caller ID List 1) When the phone is in standby mode, select the Caller ID message (see "Viewing the Caller ID List" on Press talk/flash or . The displayed phone number dials automatically. OR 1) Press talk/flash or . 2) View the Caller ID message you want to dial (see "Viewing the
  • Uniden DCT748-2 | English Owners Manual - Page 49
    or prerecorded Outgoing Messages • Voice Prompts for TAD (English, Spanish, or French) • Time and Day Announcement • Remote Message Retrieval • Toll Saver • Conversation Recording • Voice Memo • Message Alert On/Off • Retrieve TAD Messages using Handset www.uniden.com THE INTEGRATED TELEPHONE
  • Uniden DCT748-2 | English Owners Manual - Page 50
    the built in answering device from the handset. Setting a Security Code Security code allows you to set a two-digit security code so you can play your messages from a remote location. 1) Press tone. You will hear a confirmation tone. [49] THE INTEGRATED TELEPHONE ANSWERING DEVICE www.uniden.com
  • Uniden DCT748-2 | English Owners Manual - Page 51
    messages. "Announce only" answers the call but prevents the caller from leaving a message Message Alert On or Off Message Alert sounds an alert tone when you have an unheard message. If you set the Message Alert on, whenever a new message Setup menu, and then the Message Alert submenu. 2) Press /vol
  • Uniden DCT748-2 | English Owners Manual - Page 52
    confirmation tone. Setting the Call Screen Call Screen allows you to listen (from the base) to the incoming message being left by the caller before you answer the call. 1) Press menu/clear. Select the Answ. %CNN5ETGGP 1P 1HH [51] THE INTEGRATED TELEPHONE ANSWERING DEVICE www.uniden.com
  • Uniden DCT748-2 | English Owners Manual - Page 53
    ) which the answering system automaticlly plays when you receive a call. 1) With the phone in standby mode, press select/ /audio tone. 2) During the annoucement "To record memo message, press seven. To record your greeting, press eight. For help, press zero.", press 8. 3) After the announcement
  • Uniden DCT748-2 | English Owners Manual - Page 54
    outgoing message is played. 4) While the outgoing message is playing, press 6. Each time you press 6, the phone switches the outgoing message omit the prompt to leave a message, see "Recording a Personal Outgoing Message" on page 52 for instruction. The following message is pre-recorded: "Hello, no
  • Uniden DCT748-2 | English Owners Manual - Page 55
    tone, and the system announces "End of messages." The system returns to standby. After you have reviewed your new messages, you can play your old messages by pressing again. Once you have listened to a new message, it then becomes an old message. The old messages will be played in the order in which
  • Uniden DCT748-2 | English Owners Manual - Page 56
    repeatedly to find the message you want to play. To quickly scroll through a message, press and hold . The system advances through the playback at double speed. 3) Press at anytime to stop reviewing your messages and return to standby. [55] THE INTEGRATED TELEPHONE ANSWERING DEVICE www.uniden.com
  • Uniden DCT748-2 | English Owners Manual - Page 57
    cannot be replayed or retrieved. 1) Press to review your messages. 2) Press ∅ at anytime during the message to delete the message. You hear a confirmation tone and the message is deleted. 3) To delete all messages, press ∅ when the phone is in standby mode. After the announcement "To delete all
  • Uniden DCT748-2 | English Owners Manual - Page 58
    some messages can record a conversation from the handset (more than two seconds and less calls as the machine records the message. To adjust the volume, mute the Call Screen, press . From the handset Press select/ /audio tone when the system /audio tone while another handset is screening a call,
  • Uniden DCT748-2 | English Owners Manual - Page 59
    and old messages, after you have reviewed your new messages, you can play your old messages by pressing /2 again. •To switch to normal conversation, press on the handset. Remote access with the handset You can operate your answering system from another room using a handset. 1) When the phone is in
  • Uniden DCT748-2 | English Owners Manual - Page 60
    message. Total number of messages and the message number appears. The time and day that each message was received is announced after the message is played. /1 Repeat a Message /4 Delete a Message /3 Skip a Message exit the system. [59] THE INTEGRATED TELEPHONE ANSWERING DEVICE www.uniden.com
  • Uniden DCT748-2 | English Owners Manual - Page 61
    (more than two seconds and less than four minutes). The voice memo messages are recorded as an incoming messages. 1) With the phone in standby mode, press select/ /audio tone. 2) During the annoucement "To record memo message, press seven. To record your greeting, press eight. For help, press zero
  • Uniden DCT748-2 | English Owners Manual - Page 62
    about four seconds to repeat the previous message, or press 0 then 1 after about four seconds to repeat the current message. ** For Memo Record and Greeting Message Record function, the first time you automatically returns to standby. [61] THE INTEGRATED TELEPHONE ANSWERING DEVICE www.uniden.com
  • Uniden DCT748-2 | English Owners Manual - Page 63
    section require a minimum of two handsets to operate. To add additional handsets to your system, see "Expanding Your Phone" on page 12. Using DirectLink Mode In DirectLink Mode, a pair of handsets can function as two-way radios. You can have up to two pairs of handsets in DirectLink Mode at a time
  • Uniden DCT748-2 | English Owners Manual - Page 64
    phone is in DirectLink standby mode, press talk/flash (example of DirectLink from handset #1). 570# *CPFUGV &KTGEV.KPM/QFG 2) Select the handset to which you wish to DirectLink with by pressing the number keys (1-4). Your handset on either handset. Return the handset to the cradle
  • Uniden DCT748-2 | English Owners Manual - Page 65
    Intercom The intercom feature lets you communicate with another handset without using the phone line. note Making an Intercom Page 1) With the phone in standby mode, press hold/transfer/int'com. 2) Use /vol/∧ or /vol/∨ to select the handset you want to talk with, and then press select/ /audio
  • Uniden DCT748-2 | English Owners Manual - Page 66
    sounds, the display will show the ID of the handset that is transferring the call. 1) Pick up the handset from the cradle. (If AutoTalk is enabled, the handset will automatically answers when you pick it up.) 2) to the outside caller, press talk/flash. [65] MULTI-HANDSET FEATURES www.uniden.com
  • Uniden DCT748-2 | English Owners Manual - Page 67
    range, Unavailable appears in the display, and the operation will be canceled. •While a pair of handsets are in Room/ Baby Monitor mode, they cannot be used to make or receive calls. Other handsets can still make and receive calls. MULTI-HANDSET FEATURES www.uniden.com MULTI-HANDSET FEATURES [66]
  • Uniden DCT748-2 | English Owners Manual - Page 68
    electrical shock, only use the Uniden battery model and Uniden adapter model specifically designated for this product. Caution • Use only the specified Uniden battery pack (BT-446). • Do not remove the batteries from the handset to charge them. • Never throw the battery into a fire, disassemble them
  • Uniden DCT748-2 | English Owners Manual - Page 69
    appears in the display. .QY$CVVGT[ If the phone is in standby mode, none of keys will operate. If you are on a call, complete your conversation as quickly as possible, and return the handset to the cradle. Cleaning the battery charging contacts To maintain a good charge, clean the charging
  • Uniden DCT748-2 | English Owners Manual - Page 70
    : 9V DC 350mA AD-0005 for the charger (DCT748-2 only) 120V AC 60Hz 9V DC 120mA Battery Information Battery part number: BT-446 Capacity: 800mAh, 3.6V • To avoid damage to the phone use only Uniden AD-800 and AD-0005, and BT-446 with your phone. • If the handset is left off of the base, the actual
  • Uniden DCT748-2 | English Owners Manual - Page 71
    TROUBLESHOOTING Troubleshooting If your phone is not performing to your expectations, please try these simple steps first. Symptom Suggestion The charge LED won't illuminate when the handset is placed in the cradle. • Make sure the AC adapter is plugged into the base or the charger (if you have
  • Uniden DCT748-2 | English Owners Manual - Page 72
    was placed through a switchboard. • Call your local telephone company to verify your Caller ID service is current. There may be a problem with your Caller ID service. You cannot register the handset • Charge the battery pack for 15-20 hours. at the base. • Change the Digital Security Code (see
  • Uniden DCT748-2 | English Owners Manual - Page 73
    cordless phone. In case of accidental submersion, please read the following steps. TROUBLESHOOTING Case Action If the handset handset, base and the microwave oven. After following these steps, if your cordless telephone does not work, please send to: Uniden America Corporation Parts and Service
  • Uniden DCT748-2 | English Owners Manual - Page 74
    Safety Precautions Caution! To reduce the risk of fire or injury to persons by the battery, read and follow these instructions: 1. Use only the Uniden battery pack specified in the owner's manual. 2. Do not dispose of the battery pack in a fire. The cell may explode. Check the Nickel Metal Hydride
  • Uniden DCT748-2 | English Owners Manual - Page 75
    disconnect your phone to determine if it is the cause of your problem. If you determine that it is the cause, you must leave it disconnected until the trouble has been corrected. Radio Interference Radio interference may occasionally cause buzzing and humming in your cordless handset, or clicking
  • Uniden DCT748-2 | English Owners Manual - Page 76
    Ringer Equivalence Numbers of all the devices does not exceed five. RADIO EQUIPMENT The term "IC:" before the radio certification number only signifies that Industry Canada technical specifications were met. not be ensured when using this telephone". I.C. NOTICE [75] I.C. NOTICE www.uniden.com
  • Uniden DCT748-2 | English Owners Manual - Page 77
    58 Remote access away from home 60 from your handset 58 Ring options 18 Ringer mute 31 Room/baby monitor 66 S Setting up base unit 9 Handset 8 Menu options 17 Telephone Line 9 Speed dialing 40 T, U, V, W, X, Y, Z Transferring a call 65 Troubleshooting 70 Voice memo 60 Warranty 74 INDEX
  • Uniden DCT748-2 | English Owners Manual - Page 78
    Memory List Name Phone No. 1 35 2 36 3 37 4 38 5 39 6 40 7 41 8 42 9 43 10 44 11 45 12 46 13 47 14 26 60 27 61 28 62 29 63 30 64 31 65 32 66 33 67 34 68 [77] MEMORY LIST Name Phone No. 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90
  • Uniden DCT748-2 | English Owners Manual - Page 79
    Memo www.uniden.com [78]
  • Uniden DCT748-2 | English Owners Manual - Page 80
    Memo [79] www.uniden.com
  • Uniden DCT748-2 | English Owners Manual - Page 81
    6 to turn the answering system on. Remote access away from home 1. Call your phone number from a touch-tone phone. 2. During the outgoing message, press 0 and enter your PIN code. The answering system announces the number of messages stored in memory and the voice prompts. 3. To quit, hang up the
  • Uniden DCT748-2 | English Owners Manual - Page 82
    Off Help Guidance CUT Task Key Repeat a Message Playing incoming Messages Skipping a Message Deleting a Message Stop Operation Answering System On Memo Record/Stop Greeting Message Record/Stop Answer System Off Help Guidance www.uniden.com REMOTE OPERATION REMOTE OPERATION CARD
  • Uniden DCT748-2 | English Owners Manual - Page 83
    with this product, please call our Customer Hotline at 1-800-297-1023 PLEASE DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE. Our Uniden representatives will be happy to help you with any matters regarding the operation of this unit, available accessories, or any other related matters. Thank
  • Uniden DCT748-2 | English Owners Manual - Page 84
    ACGCFOEOSWROS.ONURLNIINIEDSEE, [email protected] W W R E G I S T E R O N L I N E T O D AY ! T H A N K Y O U F O R B U Y I N G A U N I D E N P R O D U C T. ©2004 Uniden America Corporation, Fort Worth, Texas. Contains additional foreign articles. Custom manufactured in China. UPZZ01343ZZ
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
DCT 748
SERIES
OWNER'S
MANUAL