Uniden DECT2080-2 English Owners Manual - Page 46

Operating the Answering System While You Are Away from Home

Get Uniden DECT2080-2 - DECT Cordless Phone PDF manuals and user guides
UPC - 050633271155
View all Uniden DECT2080-2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Operating the Answering System While You Are Away from Home You can access your answering system while you are away from home to check, play, and delete messages, or turn your answering system on and off. Notes: • The answering system will only playback messages for four minutes and then it returns to the command waiting mode. To continue playing your messages, press [0] then [2] again within fifteen seconds. • If you enter an incorrect security code three times, you will hear a beep and the answering system will return to standby. To operate from a remote location, use any touch-tone telephone, and follow these steps: ) Call your telephone number and wait for the system to answer. If the answering system is off, it will answer after about ten rings and sounds a series of beeps. 2) During the greeting or the beeps (if answering system is off), press [0] and enter your security code/PIN within two seconds (see Setting a Security Code or Personal Identification Number (PIN) on page 41). 3) The answering system announces the current time and the number of messages stored in memory.. You hear "To play incoming messages, press zero-two. For help, press one-zero" followed by a beep. 4) Enter a remote command from the chart below. You have fifteen seconds to enter the first command; after the first command, you have two seconds to enter each command. Remote Commands Command Function Command Function Command Function [0] then [1] Repeat a message* [0] then [4] Delete a message [0] then [9] Answering system off [0] then [2] Play incoming messages [0] then [5] Stop operation [1] then [0] Help [0] then [3] Skip a message [0] then [6] Answering system on * If you press [0] then [1] in the first four seconds of a message, the system skips to the previous message.. If you press [0] then [1] after the first four seconds of a message, the system repeats the current message. 5) When you finish, you will hear intermittent beeps indicating that the system is in the command waiting mode. Enter another command from the chart within fifteen seconds. 6) Hang up to exit the system. The answering system automatically returns to its normal standby setting. 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
45
Operating the Answering System While You Are Away from Home
You can access your answering system while you are away from home to check, play, and delete messages, or turn
your answering system on and off.
Notes:
The answering system will only playback messages for four minutes and then it returns to the command waiting
mode. To continue playing your messages, press
[0]
then
[2]
again within fifteen seconds.
If you enter an incorrect security code three times, you will hear a beep and the answering system will return to
standby.
To operate from a remote location, use any touch-tone telephone, and follow these steps:
Call your telephone number and wait for the system to answer. If the answering system is off, it will answer after
about ten rings and sounds a series of beeps.
During the greeting or the beeps (if answering system is off), press
[0]
and enter your security code/PIN within
two seconds (see Setting a Security Code or Personal Identification Number (PIN) on
page 4±).
The answering system announces the current time and the number of messages stored in memory.
You hear “To play incoming messages, press zero-two. For help, press one-zero” followed by a beep.
Enter a remote command from the chart below. You have fifteen seconds to enter the first command; after the
first command, you have two seconds to enter each command.
Remote Commands
Command
Function
Command
Function
Command
Function
[0]
then
[1]
Repeat a message*
[0]
then
[4]
Delete a message
[0]
then
[9]
Answering system off
[0]
then
[2]
Play incoming messages
[0]
then
[5]
Stop operation
[1]
then
[0]
Help
[0]
then
[3]
Skip a message
[0]
then
[6]
Answering system on
* If you press
[0]
then
[1]
in the first four seconds of a message, the system skips to the previous message.
If you press
[0]
then
[1]
after the first four seconds of a message, the system repeats the current message.
When you finish, you will hear intermittent beeps indicating that the system is in the command waiting mode.
Enter another command from the chart within fifteen seconds.
Hang up to exit the system. The answering system automatically returns to its normal standby setting.
•
•
±)
2)
3)
4)
5)
6)