Uniden GMR2875-2CK English Owners Manual - Page 1

GMR2872-2CK/GMR2875-2CK • 15 GMRS / 7 FRS Channels • 142 Privacy Codes (CTCSS Tone and DCS Code) • Up to 28 Mile Range* • Submersible design • Direct Call • 143 Group Codes • Silent Mode • 10 Selectable Call/Ring Tone Alerts • Backlit LCD Display • Roger Beep • Vibrate Reminder (GMR2875 Only) • Power Boost Button for Maximum Range • All Call • Auto Channel Change Call • Battery Charger • Battery Level Meter • Channel Monitor • Channel Scan • Group Scan • Keypad Lock • NOAA Emergency / Weather Channels • Emergency Weather Alert *Range may vary depending on environmental and/or topographical conditions. GMR2872-2CK/GMR2875-2CK RADIO LIQUID CRYSTAL DISPLAY 14 1 15 20 16 17 18 19 21 2 3 22 8 4 9 5 6 10 11 7 12 13 Congratulations on your purchase of the Uniden GMR2872-2CK/GMR2875-2CK (General Mobile Radio Service) waterproof radio. This lightweight, palm-sized, radio is a state-of-the-art device, equipped with many valuable features. Use it at sporting events, to stay in contact with family and friends, hiking, skiing, outdoors, or in a neighborhood watch for vital communication - even outside by the pool! Your radio complies with JIS7 water-resistant standards, which means the radio can be submerged in 1.0 meters of water for 30 minutes without damage. After your radio is submerged in water, you might notice that the sound is distorted. This is because there is still water remaining in and around the speaker and microphone. Just shake the radio to clear excess water, and the sound should return to normal. Note: If your radio is exposed to salt water, clean your radio thoroughly with fresh water, and dry it before turning it on. PACKAGE CONTENTS Your package contains two radios, two rechargeable NiMH battery packs (#BP38), one AC adapter (#AD314), one charging cradle (#RC1282), two belt clips and this reference guide. You can operate the unit using the rechargeable NiMH battery pack. To order the following optional accessories, visit our web site @www.uniden.com or call 1-800-554-3988 during business hours. Use only Uniden accessories. • NiMH Battery Pack - #BP38 • Charging Cradle - #RC1282 • AC Adapter - #AD-314 INSTALL THE BATTERY Your radio uses a supplied NiMH battery pack. To install the NiMH battery pack: 1) Make sure the radio is off. 2) Turn the screw holding the battery compartment counterclockwise with a screwdriver, and hold up the battery cover. 3) Put the NiMH battery pack in the battery compartment applying the battery contacts to the lower charge contacts. Be sure to follow the instructions written on the battery pack's label. Installing the battery pack incorrectly will prevent the unit from operating. 4) Before placing the battery cover back on the radio, check the rubber seal around the battery compartment and the ribbon of the battery pack : make sure that the seal is in good condition and that there is no foreign matter under the seal. 5) Replace the battery compartment door. Tighten the screws securely. Note: If the rubber seal appears warn, nicked, or dried out, replacement seals are available from www.uniden.com or call 1-800-554-3988 during business hours. USING THE RADIO BATTERY LEVEL AND LOW BATTERY ALERT This radio has a battery level meter that indicates the status of the batteries. When the battery level is low, the battery level meter icon flashes and then BATT appears after 30 seconds. Recharge the NiMH battery pack immediately. Warning! To avoid the risk of personal injury or property damage from fire or electrical shock, only use the Uniden accessories specifically designated for this product. GMRS LICENSE 1 Antenna 2 PTT (Push-To-Talk) Button 3 Power Boost Button 4 Monitor Button 5 Channel Up/Down Key 6 Tone/Group Key 7 D-call Key 8 Menu/Power key 9 Volume Up/Down key 10 Enter/Lock Key 11 Weather/Alert Key 12 Microphone 13 Speaker 14 Battery Level Indicator 15 Sub Code Indicator 16 Alert Indicator 17 Group Indicator 18 Receive Indicator 19 Call Indicator 20 Channel Indicator 21 Missed Call Indicator 22 Charging Contacts The radio operates on the General Mobile Radio Service (GMRS) frequencies when using Channels 1-7 and channels 15-22. You must have a GMRS license issued by the Federal Communications Commission to legally use these channels. For licensing information and application forms, visit the FCC online at: www. fcc.gov/wtb/uls or call the FCC hotline at 1-800418-3676. If you have any questions, you can contact the FCC direct at 1-888-225-5322. No license is required for operation on channels 8-14 or operation on any channel in Canada. CHARGING THE RADIO Your radio includes charging cradle and rechargeable battery packs. Follow these instructions to recharge the radios in a charging cradle. Make sure to turn the radio OFF before placing the radio in the charging cradle. Using the Charging Cradle 1) Connect the adapter's plug to DC IN 9V jack of the charging cradle and plug the other end into an AC outlet. 2) Set the charging cradle on the desk or tabletop, and place the radio in the charging cradle with the keypad facing forward. 3) Make sure that the LED illuminates. Charge the battery pack for 16 hours and remove the radio from the charging cradle after charging. Note: • Charge time may vary depending on the battery life remaining. • For fastest charging, turn off the radio before charging. Warrning!: • The charging cradle is not waterproof. If the charging cradle falls into water, unplug it before attempting to remove it from the water. Allow the cradle to dry completely before reconnecting the power. • Wipe off dirt or shake water from your radio before placing in the charging cradle if your radio is soiled or wet. USING THE RADIO In order to get the most out of your new radio, read this reference guide completely before attempting to operate the unit. Turning the Radio On and Adjusting the Volume 1) Press and hold the MENU/ to turn the radio ON. 2) To change the volume level, press the VO or to increase or decrease the volume level then press ENTER/ . 3) Press and hold the MENU/ to turn the radio OFF. Choosing a Channel Your radio has 22 channels and 142 Privacy codes you can use to talk to others. In order to speak to someone, both your radios must be set to the same channel and Privacy code. To choose a channel: Press CH or to increase or decrease the channel number displayed. • To change the channel continuously, press CH or , then repeatedly press and hold CH or for more than 1 second. Note: Channels 1-7 and 15-22 have a typical range of up to 28 miles by pressing the Power Boost. HI is displayed when you select a GMRS channel, and LO is displayed when you select a FRS channel. SETTING UP GROUP MODE In order to use Group Mode you need to initialize a couple of settings in your radio: • Set the radio to Group Mode • Set a Group Code • Set a Unit Number • Set a "Nickname" Setting the Radio to Group Mode To set the radio to Group Mode, which enables Direct Call, Auto Channel Change and All Call, press and hold TONE/GROUP for 2 seconds. The radio displays GRP and group code. Note: In group mode, you cannot receive transmissions from other radios unless they are also set to the same channel and group code. Setting the Group Code Set the group code for your radio group from 0-142. Everyone in your group must select the same group code in order to communicate with each other. 1) Tap TONE/GROUP in group mode. Press CH or to select the group number. 2) Press ENTER/ or TONE/GROUP to return to normal operation. Setting the Unit Number Each radio in your group needs to be set to a unique unit number, from 1-16. 1) Press MENU/ . Advance through the menu until UNIT appears, and then press ENTER/ . The current unit number flashes. 2) Press CH or to select the desired unit number. 3) Press ENTER/ to continue to the next section. Setting Your Nickname Your nickname appears on other units' displays when you make a All Call or direct call. This is also the name that appears on other radio displays when someone wants to make a direct call to you. When no nickname is set, the unit number appears. 1) Press MENU/ . Advance through the menu until UNIT appears, and then press ENTER/ . The current unit number flashes, then tap ENTER/ . The radio displays n - - - - (or your current nickname) with the first place in the nickname flashing. 2) Press CH or to select the letter, then ENTER/ to advance to the next letter until you have entered your nickname. 3) Press MENU/ to confirm the setting and exit the menu. Using Group Mode Group mode lets you make direct calls to other people in your group without alerting the entire group and also lets you quickly change everyone in your group to another channel from a single radio. Before using group mode, follow the instructions in "Setting Up Group Mode" on every radio in your group. Then, to record the unit ID and everyone's nickname in every radio, send a call to "All" from each radio one time (see "Sending a Direct Call"). Sending a Direct Call Direct Call lets you call everyone in your group at once, or call a single person in your group without anyone else in the group knowing. It is like a "speed dial" directly to the person(s) you want to talk to. To call everyone in your group, press D CALL in group mode. The radio flashes ALL. Then, press D CALL or ENTER/ . Everyone in your group receives a call "chirp" for about 3 seconds. When the chirp ends, begin your conversation. Note: When you make a direct call to "all," your radio also sends out your nickname or ID so that it will show up in the call list for everyone in your group. To call one person in your group, without having other people know, press D CALL in group mode. Then, use CH or to select the person you want to call and press D CALL or ENTER/ . Your radio sounds tones for 3 seconds as it sends the call. When the selected person answers, you can begin your conversation. You can silence the call tones at any time by pressing PTT or Power boost. Your conversation remains private between you and the person you called until 15 seconds after your last conversation. Then, your radio automatically exits private mode. Automatically Changing Channels Auto Channel Change lets you easily coordinate a channel change for everyone in your group. You might want to do this when you find you are getting a lot of interference on your current channel. Or, you can use this feature to change from a lowpower channel (8-14) to one of the high-powered channels (1-7, 15-22) if you need more range (or to a low-power channel if you need longer battery life). To start an auto channel change, on any radio in the group tap MENU/ . Advance through the menu until CHCX appears, then press ENTER/ . The current channel flashes. Use CH or to select the target channel. You can check whether the selected channel is clear. Then press D CALL or ENTER/ . Your radio chirps for about 10 seconds while it sends out the channel change signal. As each radio receives the channel change signal, it chirps once, then changes to the new channel. To ensure all radios make it to the new channel, we recommend you: • Make sure you are in an open environment, where the radio will get the best range. • Optimize range during the channel change signal by raising the radio over your head to give the best possible height. • Do a "roll call" on the new channel after the move to be sure no one was left behind. If you missed someone, return to the previous channel and issue the signal again. USING THE RADIO IN STANDARD MODE Use the radio in standard (not group) mode when you need to be able to communicate with radios that do not have the group feature. Choosing a Privacy Code You can select a Privacy Code from 1-142 for each channel. oFF (OFF) indicates no Privacy code selected and your radio can receive a signal regardless of the code settings of the transmitting radio. 1) Press TONE/GROUP. The Privacy code indicator flashes. 2) Press CH or to increase or decrease the code. You can also select oFF. 3) Press ENTER/ or TONE/GROUP to return to normal operation. Note: Only tones 1-38 are standard across radio brands. Other settings might differ from brand to brand. See the specifications for the specific tones used for each setting. Channel Scan Feature Your radio has a channel scan feature that lets you easily scan all 22 channels. When an active channel is detected, the radio pauses on that channel until the channel is clear. Then after a 2-second delay, the radio resumes scanning. Pressing PTT or Power boost while the scan is paused on a channel lets you transmit on that channel. To turn on channel scan: Press MENU/ . The radio displays SCAN, and then press ENTER/ .The channel number changes as the radio rapidly cycles through the channels. To turn off channel scan: Press MENU/ , PTT, Power boost, D CALL or WX/ALERT. Talking on Your Radio To talk to others using the radio: 1) Press and hold PTT or Power boost and speak in a clear, normal voice about 2-3 inches away from the microphone. While you transmit, TXHI or TXLO appears on the display according to the type of channel. To avoid cutting off the first part of your transmission, pause slightly after pressing PTT or Power boost before you start talking. 2) When you finish speaking, release PTT or Power boost. You can now receive incoming calls. While receiving, RX appears on the display. Note: When you press Power boost, BOOS appear on the display. The radio transmits at maximum power when a GMRS channel is selected. If Power boost is continuously pressed, 1 minute after you start pressing Power boost the transmission stops and you hear a boost timeout error tone. Monitor Mode Feature Your radio lets you listen for weak signals on the current channel at the press of a key. To turn on the Monitor Mode: • For brief listening, press MON. MON appears and RX flashes. • Press and hold MON for 2 seconds until two beeps sound for continuous listening. The receiver circuit stays open, so you hear both the noise and weak signals. To turn off Monitor Mode: Press MON to return to the previous mode. MON and RX disappear. Navigating through the Normal Menu To access the advanced features of your radio has a Menu function. In order to use Auto Channel Change, you need to set your radio to Group Mode. Scan Mode Silent Mode Auto Channel Change Call Tone Unit Roger Beep Setting Beep Tone ON-OFF Channel Change 1-10 Setting Unit ON-OFF ON-OFF Number Start Scanning Setting Nickname 1) To enter the menu, press MENU/ . 2) Additional presses of MENU/ advances you through the menu. After the last menu item, the radio exits to the previous mode. 3) Other ways to exit the Menu function are: a. Press PTT, Power boost, MON, D CALL, WX/ALERT or TONE/GROUP. b. Wait 10 seconds until the radio automatically returns to the previous mode. Setting Silent Mode When you turn on the silent mode, all incoming calls are muted: the radio flashes the display backlight, the channel indicator, SLNT and CALL to alert you to an incoming call. If you do not respond to the call within 15 seconds, the backlight turns off. The GMR2875 will also vibrate to remind you that you missed a call. Silent mode is disabled for 15 seconds when you transmit, receive, or press any other button. To set the silent mode: 1) Enter the menu. Advance through the menu until the SLNT appears, then press ENTER/ . The current setting flashes. 2) Press CH to display on, then press ENTER/ . Note: To prevent unwanted silent alerts, be sure to use a Privacy code or group code whenever you use the Silent mode feature. You can hear the received voice when you turn on channel scan and an active channel is detected even during silent mode. Missed Call Alerts If you receive an incoming call while silent mode is on and do not respond, the radio will turn on the Missed Call icon. If you are using the Group Mode, the radio will also indicate the person who made the call. The GMR2875 will additionally remind you of a missed call by vibrating every minute after the call for 3 minutes. Transmitting a Call Tone Your radio is equipped with 10 selectable call tones that are transmitted when you press D CALL in standard mode. The selected tone will be also heard when someone places a direct call to you. To select a call tone: 1) Enter the menu. Advance through the menu until CALL appears, then press ENTER/ . The current call tone number (1-10) flashes. 2) Press CH or to increase or decrease the number to the desired call tone. Each tone will be heard through the speaker. To transmit the selected call tone, press D CALL. The selected tone is transmitted for a fixed length of time. Call Tone is cancelled if you press PTT or Power boost. Roger Beep Roger beep is a beep that is sent to notify the end of transmission. You can hear the roger beep can be heard through the speaker when both roger beep and Beep Tone are on. When roger beep is on and Beep Tone is off, you do not hear the roger beep, but it is transmitted to your party. To adjusting the roger beep, enter MENU/ . Advance through the menu until RGR appears, then press ENTER/ . The current setting flashes. To turn OFF roger beep: Press CH to display oF, then press ENTER/ . To turn ON roger beep: Press CH to display on, then press ENTER/ . Adjusting the Sound (Beep Tone) Your radio sounds a beep each time you press a key (except for PTT and Power boost). To adjusting the sound, enter MENU/ . Advance through the menu until TONE appears, then press ENTER/ . The current setting flashes. To turn OFF this beep: Press CH to display oF, then press ENTER/ . To turn ON this beep: Press CH to display on, then press ENTER/ . Key Lock Press and hold the ENTER/ until the LOCK appears. To exit Keylock on mode, press and hold ENTER/ again. Note: • While in keylock on mode, you can still use the radio to receive transmissions, use D CALL in Standard mode, VO or , PTT, Power boost, MON, and MENU/ to turn on or off the radio.