Uniden SX507-2CKHS English Owner Manual - Page 1
Uniden SX507-2CKHS Manual
View all Uniden SX507-2CKHS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
SX507 • 7 Weather Channels • 142 Privacy Codes (CTCSS Tone and DCS Code) • Up to 50 Mile Range* • Internal VOX Circuitry • TRU Waterproof™ (IPX7/ JIS7) - Submersible and Floats • Direct Call with Name Display • 143 Group Codes • Silent Mode • 10 Selectable Call/Ring Tone Alerts • Backlit LCD Display • Roger Beep • Call Alert; Vibrate • 2 Earbuds with VOX Mic or 2 Headset Boom Mics (depending on model number) per radio • BOOST for Maximum Range* • Headset Jack • Auto Channel Change Call • Battery Level Meter • Rechargeable NiMH Batteries • Dual Charging Cradle with AC Adapter • Channel Monitor • Channel Scan Group Scan • Keypad Lock • Emergency Weather Alert • Emergency Light • Last Channel Memory • Carabiner clip (1 per radio) *Range may vary depending on environmental and/or topographical conditions. 1 10 2 3 4 11 5 12 6 13 7 14 15 8 9 Radio color/pattern varies according to model number. 1 Antenna 2 Push to Talk 9 Charging Contacts 10 MicroUSB port and earbud jack 3 Boost (Change 11 Volume (UP/DOWN) transmission power from 1.0W to 2.5W.) 4 Channel UP/DOWN 12 Enter/Lock 5 Menu/Power 13 Tone/Group 6 D Call 14 WX Alert 7 Light/MON 15 Microphone 8 Speaker Congratulations on your purchase of a Uniden SX507 series radio. This lightweight, palm-sized radio is a state-of-the-art device, equipped with many valuable features. Use it at sporting events, to stay in contact with family and friends, hiking, skiing, outdoors, or in a neighborhood watch for vital communication. Your radio complies with IPX7/JIS7 waterresistant standards, which means the radio can be submerged in 3.3 feet (1.0 meters) of water for 30 minutes without damage. • The radio will only meet this rating if fully assembled and all rubber seals and the jack cover are well maintained and correctly fitted. This means that the Headset plug is not inserted, and the Headset jack cover and the battery pack are attached and securely fastened. • After your radio is submerged in water, you might notice that the sound is distorted. This is because water remains in and around the speaker and microphone. Just shake the radio to clear excess water, and the sound should return to normal. Note: If your radio is exposed to salt water, clean your radio thoroughly with fresh water and dry it before turning it on. PACKAGE CONTENTS Each radio uses 3 rechargeable 1000mAH AA Ni-MH batteries, included. If your model number contains a "C," your package contains a microUSB Y charging cable. If your model number contains "CK," it contains a charging kit (including a charging cradle). If your models number contains "HS," it contains headsets. Refer to the packaging for other specific contents. INSTALL THE BATTERY These radios each use 3 rechargeable 1000mAH AA batteries for power (included). 1. Remove the belt clip if necessary. 2. Turn the screw holding the battery compartment counterclockwise with a screwdriver and lift up the battery cover, 3. Insert the NiMH batteries in the battery compartment according to the directions inside the case. Installing the batteries incorrectly will prevent the unit from operating. 4. Before placing the battery cover back on the radio, check the rubber seal around the battery compartment. Make sure that the seal is in good condition and that there is no foreign matter under it. 5. Replace the battery compartment door. Tighten the screws securely. 6. Replace the belt clip if necessary. Note: If the rubber seal appears worn, nicked, or dried out, replacement seals are available from www.uniden.com. CHARGING THE RADIO Follow these instructions to charge or recharge your radios. Make sure to turn the radio OFF before placing it in the charging cradle. 1. Insert the adapter's microUSB plug to DC IN 5V USB jack of the charging cradle and plug the other end into an AC outlet. 2. Set the charging cradle on a stable desk or tabletop and place the radios in the charging cradle with the keypad facing forward. 3. Make sure that the LED illuminates. Charge the batteries for 16 hours and remove the radio from the charging cradle after charging. Note: • Use only the supplied batteries and AC adapter or approved accessories from Uniden. • The batteries must be installed for the unit to operate, even if the unit is also connected to external power. • If battery power is low, you cannot operate the radio even using external power. Allow the batteries to charge before using. If you try to transmit while power is low, the radio will automatically turn off. • Charge time may vary depending on the battery life remaining. • For faster charging, turn off the radio before charging. Warning! • The charging cradle is not waterproof. If the charging cradle falls in the water, unplug it before attempting to remove it from the water. Allow the cradle to dry completely before reconnecting the power. • Wipe off dirt or shake water from your radio before placing in the charging cradle if your radio is soiled or wet. USING A HEADSET Depending on the model number, your radios may come with an earbud headset with mic on the cord or with a boom mic headset. To use a headset, lift the rubber cover from over the headset jack, then plug in the headset. Important: Your radio is not waterproof when using a headset jack. When you remove the headset, be sure to fully press the jack cover into place to restore its waterproof capability. USING RADIO BATTERY LEVEL AND LOW BATTERY ALERT This radio has a battery level meter that indicates the battery power level. When the battery level is low, the battery level meter icon flashes and then BATT appears after 30 seconds. Recharge the NiMH batteries immediately. Warning! To avoid the risk of personal injury or property damage from fire or electrical shock, only use the Uniden accessories specifically designated for this product. USING THE RADIO In order to get the most out of your new radio, read this reference guide completely before attempting to operate it. Turning the Radio On and Adjusting the Volume 1. Press and hold MENU/ to turn the radio on. 2. Press VO or to increase or decrease the volume level then press ENTER/LOCK. 3. Press and hold MENU/ to turn the radio off. Choosing a Channel Your radio has 22 channels and 142 Privacy codes you can use to talk to others. In order to speak to someone, both your radios must be set to the same channel and Privacy code. To choose a channel: Press CH or , then press CH or to increase or decrease the channel number displayed. To scroll through the channels, press CH or , then press and hold CH or for more than 1 second. Note: Channels 1-7 and 15-22 have a typical range of up to 50 miles by pressing BOOST. HI displays when you select one of these channels, and LO displays when you select channel 8 - 14. SETTING UP GROUP MODE Group mode lets several people talk on the same channel in a separate group. In order to use Group mode, you need to initialize specific settings in your radio: • Set the radio to Group mode. • Set a Group Code. • Set a Unit Number. • Set a "Nickname." Setting the Radio to Group Mode To set the radio to Group mode, which enables Direct Call, Auto Channel Change, and All Call, press and hold TONE/GROUP for 2 seconds. The radio displays GRP and group code. Note: In Group mode, you cannot receive transmissions from other radios unless they are also set to the same channel and group code. Setting the Group Code Set the group code for your radio group from 0-142. Everyone in your group must select the same group code in order to communicate with each other. 1. PressTONE/GROUP in Group mode. Press CH or to select the group number. 2. Press ENTER/LOCK or TONE/GROUP to return to normal operation. Setting the Unit Number Each radio in your group needs to be set to a unique unit number, from 1-16. 1. Press MENU/ . Advance through the menu until UNIT appears, and then press ENTER/ LOCK. The current unit number flashes. 2. Press CH or to select the desired unit number. 3. Press ENTER/LOCK to continue to the next section. Setting Your Nickname Your nickname appears on other units' displays when you make an All Call or Direct Call. This is also the name that appears on other radio displays when someone wants to make a Direct Call to you. Without a nickname, the unit number shows. 1. Press MENU/ and advance through the menu until UNIT appears; then press ENTER/LOCK. The current unit number flashes, then press ENTER/LOCK The radio displays - - - - (or your current nickname) with the first place in the nickname flashing. 2. Press CH or to select the letter, then ENTER/LOCK to advance to the next letter until you have entered your nickname. 3. Press MENU/ to confirm the setting and exit the menu. Using Group Mode Group mode lets you make direct calls to other people in your group without alerting the entire group and also lets you quickly change everyone in your group to another channel from a single radio. Before using Group mode, follow the instructions in "Setting Up Group mode" on every radio in your group. Then, to record the unit ID and everyone's nickname in every radio, send a call to "All" from each radio one time (see "Sending a Direct Call"). Sending a Direct Call Direct Call lets you call everyone in your group at once, or call a single person in your group without anyone else in the group knowing. It is like a "speed dial" directly to the person(s) you want to talk to. To call everyone in your group, press D CALL in Group mode. The radio flashes ALL. Then, press D CALL or ENTER/LOCK Everyone in your group receives a call "chirp" for about 3 seconds. When the chirp ends, begin your conversation. Note: When you make a direct call to "all," your radio also sends out your nickname or ID so that it will show up in the call list for everyone in your group. To call one person in your group without having other people know, press D CALL in Group mode. Then, use CH or to select the person you want to call and press D CALL or ENTER/LOCK. Your radio sounds tones for 3 seconds as it sends the call. When the selected person answers, you can begin your conversation. You can silence the call tones any time by pressing PTT or BOOST. Your conversation remains private between you and the person you called until 15 seconds after your last conversation. Then, your radio automatically exits Private mode. Automatically Changing Channels Auto Channel Change lets you easily coordinate a channel change for everyone in your group. You might want to do this when you find you are getting a lot of interference on your current channel. You also use this feature to change from a low-power channel (8-14) to one of the high-powered channels (1-7, 15-22) for more range (or to a low-power channel if you need longer battery life). To start an auto channel change, on any radio in the group, press MENU/ . Advance through the menu until CHCX appears, then press ENTER/LOCK. The current channel flashes. Use CH or to select the target channel. You can check whether the selected channel is clear. Then press D CALL or ENTER/LOCK. Your radio chirps for about 10 seconds while it sends out the channel change signal. As each radio receives the channel change signal, it chirps once, then changes to the new channel. To ensure all radios make it to the new channel, we recommend you: • Make sure you are in an open environment, where the radio will get the best range. • Optimize range during the channel change signal by raising the radio over your head to give the best possible height. • Do a "roll call" on the new channel after the move to be sure no one was left behind. If you missed someone, return to the previous channel and issue the signal again. USING THE RADIO IN STANDARD MODE Use the radio in Standard (not Group) mode when you need to be able to communicate with radios that do not have the group feature. Choosing a Privacy Code You can select a Privacy Code from 1-142 for each channel. oF (off) indicates no Privacy Code selected and your radio can receive a signal regardless of the code settings of the transmitting radio. 1. Press TONE/GROUP. The Privacy Code indicator flashes. 2. Press CH or to increase or decrease the code. You can also select oF. 3. Press ENTER/LOCK or TONE/GROUP to return to normal operation. Note: Only tones 1-38 are standard across radio brands. Other settings might differ from brand to brand. See the specifications for the specific tones used for each setting. Channel Scan Feature Your radio has a channel scan feature that lets you easily scan all 22 channels. When an active channel is detected, the radio pauses on that channel until the channel is clear. Then after a 2-second delay, the radio resumes scanning. Pressing PTT or BOOST while the scan is paused on a channel lets you transmit on that channel. To turn on channel scan: Press MENU/ . The radio displays SCAN. Press ENTER/LOCK. The channel number changes as the radio rapidly cycles through the channels. Use the radio in Standard (not Group) mode when you need to be able to communicate with radios that do not have the group feature. Talking on Your Radio To talk to others using the radio: 1. Press and hold PTT or BOOST and speak in a clear, normal voice about 2-3 inches away from the microphone. While you transmit, TXHI or TXLO appears on the display according to the type of channel. To avoid cutting off the first part of your transmission, pause slightly after pressing PTT or BOOST before you start talking. 2. When you finish speaking, release PTT or BOOST. You can now receive incoming calls. While receiving, RX appears on the display. Note: • When you press BOOST, BOOST appear on the display. • If BOOST, PTT or VOX is continuously used, 1 minute after you start using the feature the transmission stops and you hear a timeout error tone. Monitor Mode Feature Your radio lets you listen for weak signals on the current channel at the press of a key. To turn on the Monitor mode: • Press and hold LIGHT/MON for 2 seconds until two beeps sound for continuous listening. The receiver circuit stays open, so you hear both the noise and weak signals. To turn off Monitor mode: Press LIGHT/MON to return to the previous mode. MON and RX disappear. Navigating through the Normal Menu Your radio has a Menu function to access advanced features. In order to use Auto Channel Change, you need to set your radio to Group mode. Scan Mode Silent Mode Auto Channel Change VOX Level Start Scanning ON-OFF Channel Change OFF, 1-5 Beep Roger Unit Call Tone Beep Setting Tone Setting ON-OFF ON-OFF Unit 1-10 Number Setting Nickname 1. To enter the menu, press MENU/ . 2. Press MENU/ again to advance through the menu. After the last menu item, the radio exits to the previous mode. 3. Other ways to exit the Menu function are: a. Press PTT, BOOST, LIGHT/MON, D CALL, WX/ALERT or TONE/GROUP. b. Wait 10 seconds until the radio automatically returns to the previous mode. Setting Silent Mode When you turn on Silent mode, all incoming calls are muted, the display backlight flashes, and the channel indicator displays SLNT and CALL to alert you to an incoming call. If you do not respond to the call within 15 seconds, the backlight turns off. The radio will also vibrate to remind you that you missed a call. Silent mode is disabled for 15 seconds when you transmit, receive, or press any other button. To set Silent mode: 1. Enter the menu. Advance through the menu until the SLNT displays, then press ENTER/ LOCK. The current setting flashes. 2. Press CH to display on, then press ENTER/ LOCK. Note: To prevent unwanted silent alerts, be sure to use a Privacy Code or Group Code whenever you use the Silent mode feature. You can hear the received voice when you turn on channel scan and an active channel is detected, even during Silent mode. Missed Call Alerts If you receive an incoming call while Silent mode is on and do not respond, the radio will turn on the Missed Call icon. If you are using Group mode, the radio will also indicate who made the call. The radio also remind you of a missed call by vibrating every minute after the call for 3 minutes. Voice Operated Transmission Your radio is equipped with a user selectable Voice Operated Transmitter (VOX) that can be used for automatic voice transmissions. The VOX feature is designed to be used with a headset with a microphone. Initiate transmission by speaking into the remote microphone instead of pushing PTT and BOOST. To select the VOX level: 1. Press MENU/ . Advance through the Menu until VOX appears on the display, then press ENTER/LOCK. The current level (off, 1-5) flashes. Level oF (off) disables VOX, while levels 1-5 set the sensitivity of the VOX circuit. 2. Press either CH or to reach the desired VOX sensitivity level, then press ENTER/LOCK. Use level 1 for increased sensitivity to voice in normally quiet environments, and use a higher level to reduce undesired activation in very noisy environments. Transmitting a Call Tone Your radio is equipped with 10 selectable call tones that are transmitted when you press D CALL in Standard mode. The selected tone also will be heard when someone places a direct call to you. To select a call tone: 1. Press MENU/ . Advance through the menu until CALL appears, then press ENTER/LOCK. The current call tone number (1-10) flashes. Press CH or to increase or decrease the number to the desired call tone. Each tone will be heard through the speaker. Press ENTER/ LOCK to select a call tone. To transmit the selected call tone, press D CALL. The selected tone is transmitted for a fixed length of time. Press PTT or BOOST to cancel. Roger Beep Roger Beep is a beep that is sent to notify the end of transmission (both PTT and VOX transmission). You can hear Roger Beep through the speaker when both Roger Beep and Beep Tone are on. When Roger Beep is on and Beep Tone is off, you do not hear Roger Beep, but it is transmitted to your party. To adjust Roger Beep, press MENU/ . Advance through the menu until RGR appears, then press ENTER/LOCK. The current setting flashes. To turn off Roger Beep: Press CH LOCK. to display oF, then press ENTER/ To turn on Roger Beep: Press CH to display on, then press ENTER/ LOCK. Adjusting the Sound (Beep Tone) Your radio sounds a beep each time you press a key (except for PTT and BOOST). To adjust the sound, press MENU/ . Advance through the menu until TONE appears, then press ENTER/LOCK. The current setting flashes. To turn off the beep: Press CH to display oF, then press ENTER/ LOCK. To turn on the beep: Press CH to display on, then press ENTER/ LOCK. Key Lock Press and hold the ENTER/LOCK until LOCK appears. To turn Keylock off, press and hold ENTER/LOCK again. Note: • If Keylock is on, the radio can still receive transmissions. Use D CALL in Standard mode, VO or , PTT, BOOST, LIGHT/MON, and MENU/ to turn the radio on or off.