ViewSonic CD4233 CD4233 User Guide (English) - Page 16

Setup Procedure

Page 16 highlights

Setup Procedure 1. Install the system on the right location CAUTION: THE LCD MONITOR MUST BE MOVED OR INSTALLED BY TWO OR MORE PERSONS. Failure to follow this caution may result in injury and damage when the LCD monitor falls. CAUTION: DO NOT ATTEMPT TO INSTALL THE LCD MONITOR BY YOURSELF. The LCD display must be installed by a qualified technician. Contact your dealer for more information. CAUTION: DO NOT MOUNT OR OPERATE THE DISPLAY UPSIDE DOWN, FACE UP OR FACE DOWN.IT'S POSSIBILITY TO CLOCKWISE 90 DEGREES MOUNT. BUT DO NOT COUNTERCLOCKWISE 90 DEGREES MOUNT. CAUTION: DO NOT INSTALL THE LCD MONITOR WHERE IT WILL BE EXPOSED TO DIRECT SUNLIGHT. Failure to follow this caution will result in display defects. 3. Connect to external equipment • To protect the connected equipment, turn off the main power before making connections. • Please refer to section "Connectivity" P.18~P.22 for operations. 4. Connect power cord • The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible. • Fully insert the prongs into the power outlet socket. A loose connection may cause malfunctioning of the device. NOTE: Please refer to "Safety Operation" section of this manual for proper selection of AC power cord. IMPORTANT: Lay the protective sheet, which was wrapped around the LCD monitor when it was packaged, beneath the LCD monitor so as not to scratch the panel. 2. Install the remote control batteries The remote control is powered by 1.5V AAA batteries. To install or replace batteries: 1. Press and slide to open the cover. 2. Align the batteries according to the (+) and (-) indications inside the case. 3. Replace the cover. CAUTION: Incorrect use of batteries can result in leaks or bursting. Be careful especially about the following points. • Place "AAA" batteries matching the + and - signs on each battery to the + and - signs of the battery compartment. • Do not mix battery types. • Do not combine new batteries with used ones. It causes shorter battery life or leakage of batteries. • Remove dead batteries immediately to prevent battery liquid from leaking into the battery compartment. Don't touch exposed battery acid, it cause damage to your skin. NOTE: If you do not intend to use the Remote Control for a long period, remove the batteries. 5. Turn on the power of the attached external equipment When connected with a computer, turn on the power of the computer first. 6. Operate the attached external equipment Display the signal from the external equipment by selecting the correct video and audio sources first. 7. Adjust the sound Make adjustments to lower or to rise the volume as required. 8. Adjust the screen Make adjustments to the display position or settings if required. ViewSonic 14 CD4233

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50

Setup Procedure
1. Install the system on the right location
CAUTION:
THE LCD MONITOR MUST BE MOVED OR INSTALLED BY
TWO OR MORE PERSONS.
Failure to follow this caution may result in injury and damage
when the LCD monitor falls.
CAUTION:
DO NOT ATTEMPT TO INSTALL THE LCD MONITOR BY
YOURSELF.
The LCD display must be installed by a qualified technician.
Contact your dealer for more information.
CAUTION:
DO NOT MOUNT OR OPERATE THE DISPLAY UPSIDE
DOWN, FACE UP OR FACE DOWN.IT’S POSSIBILITY TO
CLOCKWISE 90 DEGREES MOUNT. BUT DO NOT
COUNTERCLOCKWISE 90 DEGREES MOUNT.
CAUTION:
DO NOT INSTALL THE LCD MONITOR WHERE IT WILL BE
EXPOSED TO DIRECT SUNLIGHT.
Failure to follow this caution will result in display defects.
IMPOR
T
ANT:
Lay the protective sheet, which was wrapped around the LCD
monitor when it was packaged, beneath the LCD monitor so as
not to scratch the panel.
2. Install the remote control batteries
The remote control is powered by 1.5V AAA batteries. To install
or replace batteries:
1.
Press and slide to open the cover.
2.
Align the batteries according to the (+) and (–) indications
inside the case.
3.
Replace the cover.
CAUTION:
Incorrect use of batteries can result in leaks or bursting. Be
careful especially about the following points.
Place “AAA” batteries matching the + and - signs on each
battery to the + and - signs of the battery compartment.
Do not mix battery types.
Do not combine new batteries with used ones.
It causes
shorter battery life or leakage of batteries.
Remove dead batteries immediately to prevent battery liquid
from leaking into the battery compartment. Don't touch
exposed battery acid, it cause damage to your skin.
NOTE:
If you do not intend to use the Remote Control for a long period,
remove the batteries.
3. Connect to external equipment
To protect the connected equipment, turn off the main power
before making connections.
Please refer to section “Connectivity” P.18~P.22 for operations.
4. Connect power cord
The power outlet socket should be installed as near to the
equipment as possible, and should be easily accessible.
Fully insert the prongs into the power outlet socket. A loose
connection may cause malfunctioning of the device.
NOTE:
Please refer to “Safety Operation” section of this manual for proper
selection of AC power cord.
5. Turn on the power of the attached
external equipment
When connected with a computer, turn on the power of the
computer first.
6. Operate the attached external equipment
Display the signal from the external equipment by selecting the
correct video and audio sources first.
7. Adjust the sound
Make adjustments to lower or to rise the volume as required.
8. Adjust the screen
Make adjustments to the display position or settings if required.
ViewSonic
CD4233
14