ViewSonic CDE3204 CDE3204 User Guide English - Page 8
Important Safety Instructions
View all ViewSonic CDE3204 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 8 highlights
Important Safety Instructions USE AC power Cord Keep the following guidelines to protect the AC power cord from being damaged. If the AC power cord is damaged, it may result in a fire or an electric shock. Stop using it and ask your dealer or ViewSonic service center to exchange it. • Do not place the display where the power cord is subject to wear or abuse. Dangerous Voltage: The lightning flash with • Do not pinch, bend, or twist the cord excessively. arrowhead symbol, within an equilateral triangle, • The core lines may be bared and cut, causing a short- is intended to alert the user to the presence of circuit, and resulting in a fire or an electric shock. dangerous voltage within the inside of the product • Do not convert or damage the power that may be sufficient level to constitute a risk of cord. electric shock to persons. • Avoid power cord being rolled over or Instruction: The exclamation point within an equilateral triangle is intended to alert the user to • the presence of important operating and servicing instructions in the literature accompanying the appliance. • • rested upon. When the power cord is plugged in, do not move the display. Keep the power cord away from heat sources. When you disconnect the AC power cord, disconnect it from the wall outlet first. 1. Read these instructions completely before using the equipment. 2. Keep these instructions in a safe place. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean with a soft, dry cloth. 7. Do not block any ventilation openings. Install the • When disconnecting the power cord, grasp the plug instead of pulling the power cord. • Use only an original ViewSonic AC power cord, not other brands. Do not use the supplied AC power cord on any other equipment. • The plug of power cord is intended to serve as disconnection device And the socket-outlet shall be installed close to the shredder for easy Access. equipment in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other devices (including amplifiers) that produce heat. Wall outlet Insert the plug fully into the outlet. If it is loose, do not use it. Doing so may cause arcing and result in a fire. Contact your electrician to change the outlet. 9. Do not attempt to circumvent the safety Wiring provisions of the polarized or grounding-type plug. For your safety, be sure to unplug the AC A polarized plug has two blades with one wider than power cord when connecting cables. the other. A grounding type plug has two blades and Take care not to trip on the cables. It may cause damage a third grounding prong. The wide blade and the third to the display set. prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for Electric shock replacement of the outlet. Do not touch the AC power cord or the 10. Prevent the power cord from being tread upon or display with a wet hand. If you plug/unplug pinched, particularly at the plug, convenience the AC power cord from the display with a receptacles, and the point where they exit from the wet hand, it may cause electric shock. device. Be sure that the power outlet is located near the equipment so that it is easily accessible. 11. Only use attachments/ accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, Lightning storms During a lightning storm, unplug the display from the wall outlet and disconnect the antenna to prevent damage to the display. bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus when it will be unused for a long period of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or When not in use If you will not be using the display set for long periods of time, the display set should be disconnected from the AC power outlet to prevent power line surges. The display set is not disconnected from the AC power source when the display set is switched off. To disconnect the display set completel y, unplug from the AC power outlet. plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, or the unit does not operate normally, or has been dropped. Overloading This display set is designed to operate on a 120V AC supply only. If there are too many appliances connected to the same AC power outlet, it could result in a fire or an electric shock. v