ViewSonic PJ1075 User Guide - Page 28

Power/Standby

Get ViewSonic PJ1075 PDF manuals and user guides View all ViewSonic PJ1075 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

English Changing the lamp The projection display will detect the lamp life itself. It will show you a warning message " Lamp is running out of standard lifetime. Be sure to replace the lamp as soon as possible.". When you see this message, change the lamp as soon as possible. Make sure the projection display has been cooled for at least 30 minutes before changing the lamp. Warning: Lamp compartment is hot! Allow it to cool before changing lamps! O• Lamp Changing Procedure: 1. Turn off the power to the projector by pressing the Power/Standby button. 2. Allow the projector to cool down at least 30 minutes. 3. Turn off the main power switch. 4. Disconnect the power cord. 5. Use screwdriver to remove the screw from the cover. 0 6. Remove the cover. 0 7. On the left side of the lamp module, push the electrical connector up to disengage it from the projector base. 8. Remove the three screws from the lamp module.° 9. Pull out the lamp module. 0 To replace the lamp module, reverse the previous steps. Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
English
Changing
the
lamp
The
projection
display
will
detect
the
lamp
life
itself.
It
will
show
you
a
warning
message
"
Lamp
is
running
out
of
standard
lifetime.
Be
sure
to
replace
the
lamp
as
soon
as
possible.".
When
you
see
this
message,
change
the
lamp
as
soon
as
possible.
Make
sure
the
projection
display
has
been
cooled
for
at
least
30
minutes
before
changing
the
lamp.
Warning:
Lamp
compartment
is
hot!
Allow
it
to
cool
before
changing
lamps!
O•
Lamp
Changing
Procedure:
1.
Turn
off
the
power
to
the
projector
by
pressing
the
Power/Standby
button.
2.
Allow
the
projector
to
cool
down
at
least
30
minutes.
3.
Turn
off
the
main
power
switch.
4.
Disconnect
the
power
cord.
5.
Use
screwdriver
to
remove
the
screw
from
the
cover.
0
6.
Remove
the
cover.
0
7.
On
the
left
side
of
the
lamp
module,
push
the
electrical
connector
up
to
disengage
it
from
the
projector
base.
8.
Remove
the
three
screws
from
the
lamp
module.°
9.
Pull
out
the
lamp
module.
0
To
replace
the
lamp
module,
reverse
the
previous
steps.
Warning:
To
reduce
the
risk
of
personal
injury,
do
not
drop
the
lamp
module
or
touch
the
lamp
bulb.
The
bulb
may
shatter
and
cause
injury
if
it
is
dropped.