ViewSonic PJD5112 PJD5112 User Guide (English) - Page 7

EN-4

CONTENTS

Introduction

........................................................................................................

5

Projector Features

.......................................................................................................

5

Package Contents

.......................................................................................................

6

Projector Overview

......................................................................................................

7

Using the Product

........................................................................................

9

Control Panel

..............................................................................................................

9

Connection Ports

.......................................................................................................

10

Remote Control

.........................................................................................................

11

Replacing the Battery

................................................................................................

12

Remote Control Operation

........................................................................................

13

Installation

........................................................................................................

14

Connecting the Projector

...........................................................................................

14

Powering On/Off the Projector

..................................................................................

15

Adjusting the Projector

..............................................................................................

16

Menu Operation

............................................................................................

18

Maintenance

...................................................................................................

24

Cleaning the Lens

.....................................................................................................

24

Cleaning the Projector Housing

................................................................................

24

Replacing the Lamp

..................................................................................................

25

Specifications

...............................................................................................

27

Appendix

............................................................................................................

28

LED Indicator Messages

...........................................................................................

28

Compatibility Modes

..................................................................................................

29

Troubleshooting

........................................................................................................

31

RS-232 Command and Configuration

.......................................................................

32

IR Control Code

........................................................................................................

34

ViewSonic PJD5112 PJD5112 User Guide (English) - Page 7

Contents - replacement lamp

Page 7 highlights

Section	Page
PJD5112_UG_ENG.pdf	6
Introduction	8
Projector Features	8
Package Contents	9
Projector with Lens Cap	9
AC Power Cord	9
VGA Cable (D-SUB to D-SUB)	9
Projector Overview	10
Using the Product	12
Control Panel	12
Connection Ports	13
Remote Control	14
Replacing the Battery	15
1. Push the catch to the left and remove the battery holder.	15
2. Remove the old Lithium coin cell and install new one (CR2025). Ensure that the side with the mark “+” is up.	15
3. Push the battery holder back into the remote control until you feel a click.	15
Remote Control Operation	16
Installation	17
Connecting the Projector	17
Powering On/Off the Projector	18
Powering On the Projector:	18
1. Remove the projector lens cap.	18
2. Complete the AC power cord and peripheral signal cable(s) connections.	18
3. Press button to turn on the projector. The projector takes a minute or so to warm up.	18
4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.	18
Powering Off the Projector:	18
1. Press button to turn off the projector lamp. You will see a message \	18
2. Press button again to confirm.	18
3. Disconnect the AC power cord from the electrical outlet and the projector.	18
4. Do not turn on the projector right after power off.	18
Adjusting the Projector	19
Adjusting the Projector Height	19
1. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adjustment.	19
2. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the height.	19
Adjusting the Projector Zoom and Focus	19
1. Focus the image by rotating the focus ring. A still image is recommended for focusing.	19
2. Adjust the image by sliding the zoom ring.	19
Adjusting Projection Image Size	20
Menu Operation	21
1. Press the MENU button to open the OSD menu.	23
2. When OSD is displayed, use p / q to select any feature in the main menu.	23
3. After selecting the desired main menu item, press u to enter sub-menu for feature setting.	23
4. Use p / q to select the desired item and adjust the settings with t / u.	23
5. Press the MENU button, the screen will return to the main menu.	23
6. To exit OSD, Press the MENU button again. The OSD menu will close and the projector will automatically save the new settings.	23
Maintenance	27
Cleaning the Lens	27
Cleaning the Projector Housing	27
Cleaning the Filter Cover	27
1. Switch the projector off and unplug the AC power cord from the wall socket.	27
2. Remove the filter cover as the illustration shown.	27
3. Clean the filter cover.	27
4. Replace the filter cover.	27
5. Attach the filter cover.	27
6. Plug the power back into the projector.	27
Replacing the Lamp	28
1. Turn off the projector.	29
2. If the projector is installed in a ceiling mount, remove it	29
3. Unplug the power cord.	29
4. Loosen the screw in the side of the lamp cover and remove the cover.	29
5. Remove the screws from the lamp module, raise the handle, and lift out the module.	29
6. Insert the new lamp module into the projector and tighten the screws.	29
7. Replace the lamp cover and tighten the screw.	29
8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.	29
9. Reset the lamp hour. Refer to the “Setting” menu.	29
Specifications	30
Appendix	31
LED Indicator Messages	31
Compatibility Modes	32
Computer:	32
Video:	33
Troubleshooting	34
Start-up problems	34
Image problems	34
RS-232 Command and Configuration	35