Home » ViewSonic Manuals » Projectors » ViewSonic PJD6210-3D » Manual Viewer

ViewSonic PJD6210-3D User Guide - Page 13

Connection Ports

UPC - 766907345926

View all ViewSonic PJD6210-3D manuals

Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Connection Ports 1 2 3 1 RS232 Reserved for installation control and firmware upgrades. 2 COMPUTER IN Connect image input signal (analog RGB or component) to this jack. 3 VIDEO Connect composite video output from video equipment to this jack. ViewSonic 0 PJD6210/PJD6210-WH

Section	Page
VPD-X450_En_0403.pdf	8
Projector Features	8
Package Contents	9
Projector with Lens Cap	9
AC Power Cord	9
VGA Cable (D-SUB to D-SUB)	9
Projector Overview	10
Using the Product	12
Control Panel	12
Connection Ports	13
Remote Control	14
Replacing the Battery	15
1. Push the catch to the left and remove the battery holder.	15
2. Remove the old Lithium coin cell and install new one (CR2025). Ensure that the side with the mark “+” is up.	15
3. Push the battery holder back into the remote control until you feel a click.	15
Remote Control Operation	16
Installation	17
Connecting the Projector	17
Powering On/Off the Projector	18
Powering On the Projector:	18
1. Remove the projector lens cap.	18
2. Complete the AC power cord and peripheral signal cable(s) connections.	18
3. Press button on the control panel or the POWER button on the remote control to turn on the projector. The projector takes a minute or so to warm up.	18
4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.	18
Powering Off the Projector:	18
1. Press button on the control panel or the POWER button on the remote control to turn off the projector lamp. You will see a message \	18
2. Press button on the control panel or the POWER button on the remote control again to confirm.	18
3. Disconnect the AC power cord from the electrical outlet and the projector.	18
4. Do not turn on the projector right after power off.	18
5. This projector supports Off-To-Go function. User can safely cut off the power source immediately without causing harm to the projector lamp.	18
Adjusting the Projector	19
Adjusting the Projector Height	19
Adjusting the Projector Zoom and Focus	19
1. Focus the image by rotating the focus ring. A still image is recommended for focusing.	19
2. Adjust the image by sliding the zoom ring.	19
Adjusting Projection Image Size	20
Menu Operation	21
1. Press the MENU button to open the OSD menu.	22
2. When OSD is displayed, use p / q to select any feature in the main menu.	22
3. After selecting the desired main menu feature, press u to enter sub-menu for feature setting.	22
4. Adjust the settings with t / u.	22
5. Press the MENU button, the screen will return to the main menu.	22
6. To exit OSD, Press the MENU button again. The OSD menu will close and the projector will automatically save the new settings.	22
Maintenance	25
Cleaning the Lens	25
Cleaning the Projector Housing	25
Replacing the Lamp	26
1. Turn off the projector.	27
2. Unplug the power cord.	27
3. Loosen the screw in the lamp cover and remove the cover.	27
4. Loosen the two screws from the lamp module.	27
5. Pull up the handle, and then pull out the lamp unit by the handle.	27
6. Insert a new lamp module into the projector and tighten the screws.	27
7. Replace the lamp cover and tighten the screw.	27
8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.	27
9. Reset the lamp hour. Refer to the Setting (Computer / Video Mode) menu.	27
Specifications	28
Appendix	29
LED Indicator Messages	29
Compatibility Modes	30
Computer:	30
Video:	30
Troubleshooting	31
Start-up problems	31
Image problems	31
RS-232 Command and Configuration	32