Viking DFWB300R Designer Stainless Steel Handle Kit - 41 inch - Installation I - Page 2

IMPORTANT, Handle Installation

Get Viking DFWB300R PDF manuals and user guides View all Viking DFWB300R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

IMPORTANT-Please Read and Follow! • Before beginning, please read these instructions completely and carefully. • Use caution during assembly to minimize scratches. • Do not remove permanently affixed labels, warnings or plates from the product. This may void the warranty. • Please refer to the DFRB5, DFFB5 and DFWB Installation Instructions for more information on installing the door panel. • The installer should leave instructions with the customer who should retain for local inspector's use and future reference. Installation with Wooden Full Overlay Custom Door Front Parts Included Part Designer Handles #10 x 3/4" Hex Head Screws Installation Instructions Quantity (1) (4) Required Tools Electric Drill 3/16" (0.5 cm) Drill Bit 7/16" (1.1 cm) Spade or Forstner Bit (Counterbore) Tape Measure Hex Head Screw Driver Masking Tape and Pencil To Install: 1. Locate the wooden custom panel. 2. Using the illustrations on the next page, layout the handle location on the panels. It is recommended that masking tape be placed where the four holes will be drilled to help mark the hole placement and to prevent any damage to the door when drilling the holes. 3. The Designer handle will be mounted using (4) of the #10 x 3/4" Hex head screws provided. Using the 3/16"(0.5 cm) drill bit, drill completely through the door in the hole locations. Using the 7/16" (1.1 cm) bit, counter-bore four holes 1/2" (1.2 cm) deep max. on the BACKSIDE of the custom door panel. 4. Attach the Designer handle to the panel using (4) #10 x 3/4" screws provided. 2 Handle Installation 1-1/2" (3.8 cm) 13/16" (2.1 cm) 13-1/8" (33.3 cm) 38-19/32" (98.0 cm) A A 36" Custom Door DFRB All Refrigerator/DFFB All Freezer (Front View) Designer Handle Section A-A 13/16" (2.1 cm) 3/4" (1.9 cm) Full Overlay Panel 7/16" (1.1 cm) Counter Bore x 1/2" Depth (max) 3/16" (0.5 cm) Thru Hole 3

  • 1
  • 2
  • 3
  • 4
IMPORTANT–
Please Read and Follow!
2
3
•
Before beginning, please read these instructions completely and carefully.
•
Use caution during assembly to minimize scratches.
•
Do not remove permanently affixed labels, warnings or plates from the product. This may
void the warranty.
•
Please refer to the DFRB5, DFFB5 and DFWB Installation Instructions for more information
on installing the door panel.
•
The installer should leave instructions with the customer who should retain for local
inspector’s use and future reference.
Parts Included
Required Tools
Handle Installation
To Install:
Installation with Wooden Full Overlay
Custom Door Front
1. Locate the wooden custom panel.
2. Using the illustrations on the next page, layout the handle location on the panels. It is
recommended that masking tape be placed where the four holes will be drilled to help mark
the hole placement and to prevent any damage to the door when drilling the holes.
3. The Designer handle will be mounted using (4) of the #10 x 3/4” Hex head screws provided.
Using the 3/16”(0.5 cm) drill bit, drill completely through the door in the hole locations.
Using the 7/16” (1.1 cm) bit, counter-bore four holes 1/2” (1.2 cm) deep max. on the
BACKSIDE
of the custom door panel.
4. Attach the Designer handle to the panel using (4) #10 x 3/4” screws provided.
Part
Quantity
Designer Handles
#10 x 3/4” Hex Head Screws
Installation Instructions
(1)
(4)
Electric Drill
3/16” (0.5 cm) Drill Bit
7/16” (1.1 cm) Spade or Forstner Bit (Counterbore)
Tape Measure
Hex Head Screw Driver
Masking Tape and Pencil
A
A
13-1/8”
(33.3 cm)
13/16”
(2.1 cm)
38-19/32”
(98.0 cm)
1-1/2”
(3.8 cm)
Section A-A
36” Custom Door
DFRB All Refrigerator/DFFB All Freezer
(Front View)
Designer Handle
3/4” (1.9 cm)
Full Overlay
Panel
3/16” (0.5 cm)
Thru Hole
7/16” (1.1 cm)
Counter Bore x 1/2”
Depth (max)
13/16”
(2.1 cm)