Viking FDSB5481 Professional Stainless Steel Handle Kit - DFBB - Installation - Page 2
IMPORTANT, Handle Installation - professional series
View all Viking FDSB5481 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
IMPORTANT-Please Read and Follow! • Before beginning, please read these instructions completely and carefully. • Use caution during assembly to minimize scratches. • Do not remove permanently affixed labels, warnings or plates from the product. This may void the warranty. • Please refer to the DFSB5, DFBB5 or DFBB Installation Instructions for more information on installing the refrigerator door panel. • The installer should leave instructions with the customer who should retain for local inspector's use and future reference. Installation with Wooden Full Overlay Custom Door Front Parts Included Part Quantity Professional Series Handle Tubes (2) Professional Series End Caps (4) 1/4" x 1" Phillips Head Screws (8) Installation Instructions Required Tools Electric Drill 5/16" (.8 cm) Drill Bit 5/8" (1.6 cm) Spade or Forstner Bit (Counterbore) Tape Measure Phillips Head Screwdriver Masking Tape and Pencil Rubber Mallet To Install: 1. Locate the wooden custom panel. 2. Using the illustrations on the next page, layout the handle location on the panels. It is recommended that masking tape be placed where the four holes will be drilled to help mark the hole placement and to prevent any damage to the door when drilling the holes. 3. Each Professional Series handle will be mounted using (4) of the 1/4" x 1" Phillips head screws provided. Using the 5/16"(.8 cm) drill bit, drill completely through the door in the hole locations. Using the 5/8" (1.6 cm) bit, counter-bore two holes 1/4" (.6 cm) deep on the BACKSIDE of the custom door panel. 4. Place a handle end cap on both ends of the handle tube. Tap the endcaps firmly into place with a rubber mallet ensuring that both endcaps mounting surfaces are parallel. 5. Align the holes in the endcaps with the holes on the panel and attach the Professional handle to the panel using the (4) 1/4" (.6cm) screws provided. 6. Repeat steps 1 - 4 to attach other handle. 2 Handle Installation 17-15/16" (45.6 cm) 5/16" (.8 cm) through-holes with 5/8" x 1/4" counterbore *See section A-A. 27-1/2" (69.9 cm) 1-3/8" (3.5 cm) 1-9/16" (4.0 cm) A A 1-3/8" (3.5 cm) 9" (22.9 cm) 5/16" (.8 cm) through-holes with 5/8" x 1/4" counterbore *See section A-A. 34-11/16" (88.1 cm) AA 1-3/8" (3.5 cm) 1-9/16" (4.0 cm) CL 1-9/16" (4.0 cm) 31-11/16" (80.5 cm) Custom Door DFSB5 Side-by-Side (Front View) Professional Series Handle Section A-A Professional Series Handle (Applies to DFSB5/DFBB5 Only) 5/8" (1.6 cm) Ø x 1/4" (.6 cm) counterbore 1-3/8" (3.5 cm) Custom Door DFBB5/DFBB Bottom Mount (Front View) Professional Series Handle Section A-A Professional Series Handle 5/8" (1.6 cm) Ø x 1/4" (.6 cm) counterbore 1/4" (.6 cm) Base Panel 1-3/8" (3.5 cm) 5/16" (.8 cm) Ø through-holes 3/4" (1.8 cm) Full Overlay Panel 5/16" (.8 cm) Ø through-holes 3/4" (1.8 cm) Full Overlay Panel Specifications subject to change without notice. 3