Viking RDSCE2305BSS Countertop Rear Trim - Installation Instructions - Page 3

Curb Bases, Rear Trim Accessories

Get Viking RDSCE2305BSS PDF manuals and user guides View all Viking RDSCE2305BSS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

Rear Trim Accessories Custom VGIC ranges and 60" VGCC ranges require that two 1" standoff spacers be attached to the back of the range when using a range with a backguard against a combustible surface. (See Figure 4) Figure 4 Once you determine whether or not your product needs the provided spacers, the backguard is ready to be attached. Simply slide the backguard down onto the rear of the unit and attach using the (4) screws provided. (See Figure 5) A Figure 5 IMPORTANT: USE OF ISLAND TRIM WITH AND WITHOUT 6" (15.2 CM) CLEARANCE. Normal installation for island trim on either a range or rangetop is in an island/peninsula or where there is a minimum clearance of 6"(15.2 cm) to any type of wall at the rear of the unit. However, agency authorization has been received for island trim installations where a range or rangetop can be installed at zero clearance to the rear wall as long as the wall is non-combustible. The responsibility for ensuring that the rear wall is noncombustible and heat resistant lies with the individual owner and/or end user. Only in those cases where the island trim is installed with 6" (15.2 cm) of minimum clearance to a rear wall, or when a truly non-combustible material is used, will the warranty apply. In no case will Viking Range Corporation accept responsibility for any claims which may result from heat damage against a rear wall, including cosmetic damage. It is the total responsibility of the owner/end user to ensure that the material utilized in such applications is not only noncombustible, but is also truly heat-resistant. 4 Curb Bases STANDARD CURB BASE FRONT 1. The standard curb base front (A) is completely assembled. 2. Remove the assembly from the carton and simply clip onto the front range legs. 3. The assembly is adjustable about 2" (5.1 cm) front to back so that alignment with the cabinet toe front is possible. Loosen brackets on each side, but allow snug fit. Clip assembly onto range legs; determine front to back setting; remove, tighten bolts, and reattach. A Alternate Curb Base View for Custom Ranges Important Note: The range must be installed as specified in the range installation guide for proper airflow when using the standard curb base. 5

  • 1
  • 2
  • 3
  • 4
5
4
Curb Bases
Alternate Curb Base View
for Custom Ranges
STANDARD CURB BASE FRONT
1. The standard curb base front (A) is completely assembled.
2. Remove the assembly from the carton and simply clip onto the front range legs.
3. The assembly is adjustable about 2” (5.1 cm) front to back so that alignment with the cabinet
toe front is possible. Loosen brackets on each side,
but allow snug fit.
Clip assembly onto
range legs; determine front to back setting; remove, tighten bolts, and reattach.
A
IMPORTANT: USE OF ISLAND TRIM WITH AND WITHOUT 6” (15.2 CM) CLEARANCE.
Normal installation for island trim on either a range or rangetop is in an island/peninsula or where there is a
minimum clearance of 6”(15.2 cm) to any type of wall at the rear of the unit. However, agency authorization has
been received for island trim installations where a range or rangetop can be installed at zero clearance to the
rear wall as long as the wall is non-combustible.
The responsibility for ensuring that the rear wall is non-
combustible and heat resistant lies with the individual owner and/or end user. Only in those cases where the
island trim is installed with 6” (15.2 cm) of minimum clearance to a rear wall, or when a truly non-combustible
material is used, will the warranty apply. In no case will Viking Range Corporation accept responsibility for any
claims which may result from heat damage against a rear wall, including cosmetic damage. It is the total
responsibility of the owner/end user to ensure that the material utilized in such applications is not only non-
combustible, but is also truly heat-resistant.
Once you determine whether or not your product needs the provided spacers, the backguard is ready
to be attached.
Simply slide the backguard down onto the rear of the unit and attach using the (4) screws provided.
(See
Figure 5
)
A
Figure 5
Rear Trim Accessories
Custom VGIC ranges and 60” VGCC ranges require that two 1” standoff spacers be attached to the
back of the range when using a range with a backguard against a combustible surface. (See
Figure 4
)
Figure 4
Important Note:
The range must be installed as specified in the range installation guide for proper
airflow when using the standard curb base.