Viking VGBQ3002RE2NSS Installation Instructions - Page 7
Built-In Information, General Information - appliances
View all Viking VGBQ3002RE2NSS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 7 highlights
General Information • Keep grill area clear and free from combustible materials, gasoline, and other flammable vapors. • When the outdoor grill is not in use, the gas supply must be turned off at the LP gas supply cylinder. • The pressure regulator and hose assembly supplied with the outdoor grill must be used. Replacement pressure regulators and hose assemblies must be those specified by the manufacturer. • Finding a leak is not a "do-it-yourself" procedure. Some leaks can only be found with the burner control in the on position and this must be done by a qualified technician. • The LP supply cylinder to be used must be constructed and marked in accordance with the specifications for LP- gas cylinders of the U.S. Department of Transportation (DOT) or the National Standard of Canada, CAN/CSA- B339, Cylinders, Spheres, and Tubes for the Transportation of Dangerous Goods. • Use only extension cords with a 3-prong grounding plug, rated for the power of the equipment, and approved for outdoor use with a W-A marking. • Gas Manifold Pressure- Natural gas - 4.0" W.C.P. LP/Propane - 10.0" W.C.P. WARNING If the following instructions are not followed exactly, a fire causing death or serious injury may occur: o Do not store a spare LP gas cylinder under or near this appliance. o Never fill the cylinder beyond 80 percent full. WDAARNNGIENRG This outdoor gas grill is not intended to be installed inside a home or on recreational vehicles and/or boats. WARNING Keep electrical supply cord and the fuel supply hose away from heated surfaces. CDAAUNTGIOENR WARNING This appliance is not fused. Installer must install a ground fault interrupt. DANGER CAUTION DANGER FOR YOUR SAFETY CAUTION CAUTION FOR YOUR SAFETY 12 FOR YOUR SAFETY Built-In Information • A minimum of 6" (15.2 cm) from the sides, or a minimum of 8" (20.3 cm) from the right side if there is a rotisserie motor and a minimum of 24" (61.0 cm) from the back must be maintained from the grill above the cooking surface to adjacent vertical combustible construction. The grill is not to be located under overhead unprotected combustible construction. • A minimum of 3" (7.6 cm) clearance from the back of the grill with a canopy and a minimum of 6" (15.2 cm) from the back of the grill without a canopy to noncombustible construction is required for the purpose of allowing the lid to open fully and for proper ventilation. • Note that the grill exhausts combustion products and cooking greases to the back. Never locate the grill in a location where the exhaust is directed at a window, less than 24" (61.0 cm) to combustible material or any surface that is difficult to clean. • It is desirable to allow at least 6" side clearance to non-combustible construction above the cooking surface for counter space. If using the rotisserie option, the space is essential for motor and skewer clearance. The grill can be placed directly adjacent to combustible and/or noncombustible construction below the cooking surface. • When determining a suitable location for the grill, take into account concerns such as exposure to wind, proximity to traffic paths and keeping gas supply lines as short as possible. Locate the grill only in a well-ventilated area. Never locate the grill in a building, garage, shed or other such fully enclosed areas. During heavy use, the grill will produce a lot of smoke. Ensure there is adequate area for it to dissipate. T-Series Grills: • When using a rear wall, locate the electrical service on the right hand side for the rotisserie motor. The rotisserie motor requires a 110/120 volt supply. The power supply cord on the motor is equipped with a 3-prong (grounded) plug for protection against shock hazard. Do not cut or remove the grounding from the plug. The electrical service must be equipped with a properly grounded 3-prong receptacle as required by the National Electrical Code ANSI/NFPA 70-latest edition. Installation in Canada must be in accordance with the Canadian Electrical Code, CSA 22.1 and local codes. E-Series Grills: • When using a rear wall, locate a 110/120 volt supply outlet on the bottom left hand side beneath the solid bottom support at a maximum distance of 2 feet. This connection is to be used for the ignition system and canopy lights. In addition, the rotisserie motor requires a separate 110/120 volt supply to be located on the right hand side of the grill. Both the power supply cords for the ignition/lights and the rotisserie motor are equipped with a 3prong (grounded) plug for protection against shock hazard. Do not cut or remove the grounding from the plug. The electrical service must be equipped with a properly grounded 3-prong receptacle as required by the National Electrical Code ANSI/NFPA 70-latest edition. Installation in Canada must be in accordance with the Canadian Electrical Code, CSA 22.1 and local codes. IMPORTANT: Gas fittings, regulator, and installer supplied shut-off valve must be easily accessible. 13