Viking VMOS201SS Flush-mount Kit for VMOS Microwave with 27 inch Trim Kit - In - Page 1

Viking VMOS201SS Manual

Get Viking VMOS201SS PDF manuals and user guides View all Viking VMOS201SS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

5/16" (8.77 mm) =" Centerline to hole 12-13/16" (324.63 mm) =" Centerline to cutout 13-7/16" (341.6 mm) =" Cutout Opening Width 26-15/16" (683.2 mm) BUILT-IN TRIM KIT FLUSH MOUNTING TEMPLATE FOR CUSTOM SERIES MICROWAVE OVEN 1. Align the Flush Mounting Template center line with the center of the cabinet. Align the Floor Line with the bottom of the cabinet at the desired height. Tape it in place. 2. Cut the cabinet opening along the three Cabinet Cutout Lines and the Floor Line. 3. Install two Side Spacers (see FIGURE 1) and two Bottom Spacers (see FIGURE 2) as specified in FIGURE 4. 4. Cut out the Side Spacer Templates (R and L) and align the indicated edge to the corresponding Side Spacer (see FIGURE 3). Be careful to align the Floor Line to the bottom edges of the Side Spacers. 5. Predrill two holes indicated "A" in Side Spacer - R with a / " drill bit. 6. Predrill two holes indicated "B" in Side Spacer - L with a / " drill bit. 7. Remove template from the cabinet. CENTER LINE (2) bottom spacers 24-5/8" width 1" (25.4 mm) FIGURE 1 Side Spacer (2 required) Must protrude from edge of cabinet cutout towards center as shown. FIGURE 2 Bottom Spacers (2 required). TINSKB140MRR0 VBA @" Centerline to hole 14-5/16" (362.73 mm) @" Centerline to cutout 14-15/16" (379.71 mm) @" Cutout Opening Width 29-15/16" (759.42 mm) 1-9/16" height CABINET CUTOUT LINE The exhaust duct should be aligned left to right with the left and right edges of the bottom spacer. The front edge of the exhaust duct should be recessed from the edge of the bottom spacer by 5 mm in order for the unit to be flush with the front surface of the trim kit. The exhaust duct should be secured to the bottom spacer with Screw (C). 24-5/8" (625.5 mm) 4" (2) Bottom Spacer 22-1/16" (561.0 mm) 12-1/8" (308.45 mm) TOP VIEW 4" 1-15/16" (50.35 mm) FIGURE 3 Front of Cabinet (1) Bottom Spacer 1-15/16" (49.9 mm) Edges to align Side Spacer Templates (R and L) Side Spacer L Side Spacer R FIGURE 4 Bottom Spacers centered with cabinet cutout FLOOR LINE OF CUTOUT OPENING 2-13/16" (71.1 mm) CABINET CUTOUT LINE Height Distance Between Holes A 14-1/4" (361.8 mm) Cutout Opening Height 19-7/8" (504 mm) 5/16" (8.77 mm)

  • 1
@
"
Center
line to cutout 14-15/16" (379.71 mm)
@
"
Center
line to hole 14-5/16" (362.73 mm)
5/16" (8.77 mm)
FIGURE 1
Side Spacer (2 required)
Must protrude from edge of cabinet
cutout towards center as shown.
(2) bottom spacers
24-5/8" width
1-9/16" height
FIGURE 2
Bottom Spacers (2 required).
FIGURE 3
Front of Cabinet
BUILT-IN TRIM KIT
FLUSH MOUNTING TEMPLATE
FOR CUSTOM SERIES MICROWAVE OVEN
5/16" (8.77 mm)
@
"
Cutout Opening Width 29-15/16" (759.42 mm)
CABINET CUTOUT LINE
FLOOR LINE OF CUTOUT OPENING
CENTER LINE
Cutout Opening Height 19-7/8" (504 mm)
1"
(25.4 mm)
VBA
1.
Align the Flush Mounting Template center line with the center of the cabinet. Align
the Floor Line with the bottom of the cabinet at the desired height. Tape it in place.
2.
Cut the cabinet opening along the three Cabinet Cutout Lines and the Floor Line.
3.
Install two Side Spacers (see FIGURE 1) and two Bottom Spacers (see FIGURE 2) as
specified in FIGURE 4.
4.
Cut out the Side Spacer Templates (R and L) and align the indicated edge to the
corresponding Side Spacer (see FIGURE 3). Be careful to align the Floor Line to the
bottom edges of the Side Spacers.
5.
Predrill two holes indicated “
A
“ in Side Spacer -
R
with a
1/±6
" drill bit.
6.
Predrill two holes indicated ”
B
“ in Side Spacer -
L
with a
1/±6
" drill bit.
7.
Remove template from the cabinet.
The exhaust duct should be aligned left to right with the left and right edges of the
bottom spacer. The front edge of the exhaust duct should be recessed from the edge of
the bottom spacer by 5 mm in order for the unit to be flush with the front surface of the
trim kit. The exhaust duct should be secured to the bottom spacer with Screw (C).
1-15/16" (50.35 mm)
1-15/16" (49.9 mm)
22-1/16" (561.0 mm)
24-5/8" (625.5 mm)
4"
4"
(1) Bottom Spacer
(2) Bottom Spacer
TOP VIEW
12-1/8" (308.45 mm)
FIGURE 4
Bottom Spacers centered with cabinet cutout
Edges to align Side Spacer Templates (R and L)
Side Spacer -
L
Side Spacer -
R
Height Distance Between Holes
A
14-1/4" (361.8 mm)
2-13/16"
(71.1 mm)
CABINET CUTOUT LINE
=
"
Center
line to hole 12-13/16" (324.63 mm)
=
"
Center
line to cutout 13-7/16" (341.6 mm)
=
"
Cutout Opening Width 26-15/16" (683.2 mm)
TINSKB140MRR0