Viking VUWC1541CRSS Installation Instructions - Page 5

Door Swing DFUW 24W. - Dual Zone

Get Viking VUWC1541CRSS PDF manuals and user guides View all Viking VUWC1541CRSS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

SPECIFICATIONS/DIMENSIONS DESIGNER - 24" W. Models Basic Electric Data • 115 VAC/60 Hz • Maximum amps - 3.3 • Approximate Shipping Weight Single Zone - 140 lbs. (63.2 kg) Dual Zone - 170 lbs. (76.5 kg) Dimensions DFUW 24"W. - Dual Zone (3708-.13/c4m") (2630-.67/c8m") (2(2561340-.-.6177//cc28mm"")) (w3((e88li4ext68mh3tmg-e..tsl4334naeoifndvx/u"cce.e.l4mmlldyin")))g Door Swing DFUW 24"W. - Dual Zone 23-7/8" (60.6 cm) 21-1/2" (54.6 cm) 23-11/16" (60.2 cm) to front of locally supplied custom panel 90.0° 46-1/2" (118.1 cm) 8 CUSTOM WOOD FRAME INSTALLATION (DFUW Model) NOTE: Weight of wood panel must not exceed 20 lbs. Step 1: Verify door alignment The door should be parallel to the sides and top of the refrigerator. If alignment is necessary the door may be adjusted by loosening the 2 screws which secure the hinge adapter brackets to the door and adjusting the door side to side. Use a 5/32" allen wrench for this procedure. (See Figure 1 below). Top hinge pin Remove to remove the door Hinge adaptor screws Loosen these to adjust door, on the top and bottom of the door Door must be parallel to top and sides of refrigerator 9/32" (7 mm) Figure 1 Step 2: Remove door Remove the top hinge pin from the hinge with an 1/8" allen wrench. Remove the door by angling the top of the door outward and lifting the door off the bottom hinge. (See detail in Figure 1). Step 3: Remove gasket Lay the door on its front being careful not to scratch it. Remove the door gasket by peeling up and out of the channel. Step 4: Cut overlay panel Depending on the refrigerator model cut the overlay panel to the dimensions shown. Use Figure 2 and Table A. Note: For overlay with lock option, panel thickness to be 3/4" (19 mm) maximum to 5/8" (16 mm) minimum. Note: For the door closer to work properly, it is necessary to maintain a minimum space of 9/32" (7mm) between the door and cabinet flange as shown. This space can be adjusted by adjusting the top and bottom hinge adapters. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
9
CUSTOM WOOD FRAME INSTALLATION (DFUW Model)
NOTE:
Weight of wood panel must not exceed 20 lbs.
30-3/4”
(78.1 cm)
21-1/2”
(54.6 cm)
23-7/8”
(60.7 cm)
23-7/8”
(60.6 cm)
23-7/8”
(60.6 cm)
23-7/8”
(60.6 cm)
34”
(86.4 cm)
min.
to
34-3/4”
(88.3 cm)
max.
(with leveling
legs fully
extended)
SPECIFICATIONS/DIMENSIONS
DESIGNER - 24” W. Models
Basic Electric Data
• 115 VAC/60 Hz
• Maximum amps - 3.3
• Approximate Shipping Weight
Single Zone - 140 lbs. (63.2 kg)
Dual Zone - 170 lbs. (76.5 kg)
Dimensions DFUW 24”W. - Dual Zone
Door Swing DFUW 24”W. - Dual Zone
23-7/8”
(60.6 cm)
90.0°
46-1/2”
(118.1 cm)
21-1/2”
(54.6 cm)
23-11/16”
(60.2 cm)
to front of
locally supplied
custom panel
8
Step 1: Verify door alignment
The door should be parallel to the sides and top of the refrigerator. If alignment is necessary the door may be
adjusted by loosening the 2 screws which secure the hinge adapter brackets to the door and adjusting the door side
to side. Use a 5/32” allen wrench for this procedure. (See Figure 1 below).
Figure 1
9/32”
(7 mm)
Door must be
parallel to top and
sides of refrigerator
Hinge adaptor screws -
Loosen these to adjust
door, on the top and
bottom of the door
Top hinge pin -
Remove to remove
the door
Step 2: Remove door
Remove the top hinge pin from the hinge with an 1/8” allen wrench. Remove the door by angling the top of the door
outward and lifting the door off the bottom hinge. (See detail in Figure 1).
Step 3: Remove gasket
Lay the door on its front being careful not to scratch it. Remove the door gasket by peeling up and out of the channel.
Step 4: Cut overlay panel
Depending on the refrigerator model cut the overlay panel to the dimensions shown. Use Figure 2 and Table A.
Note:
For overlay with lock option, panel thickness to be 3/4” (19 mm) maximum to 5/8” (16 mm) minimum.
Note:
For the door closer to work properly, it is necessary to maintain a minimum space of 9/32” (7mm) between the
door and cabinet flange as shown. This space can be adjusted by adjusting the top and bottom hinge adapters.