Viper 8701V Owner Manual - Page 1

Viper 8701V Manual

Get Viper 8701V PDF manuals and user guides View all Viper 8701V manuals
Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

Assembly Guide: Viper Responder LE Case ASSY-LE-CASE-VIPER 2008-11 3a. Below are instructions for disassembly and assembly of the Viper Responder LE, and for the companion 1-way remotes. This guide applies to remote controls with Replacement Part Number (RPN) 7251V or 7152V. Finding the RPN, replacement part number Turn your remote control over and remove the battery door. With the door removed read the silk-screen on the back case to find the RPN, as shown below. b. 1-800-274-0200 1-800-274-0200 RPN 7251V RPN 7152 IC:1513A -7251 FCC D:EZSDEI7251 BATTERY: CR2016 IC: 1513A-7152 FCC ID: EZSDEI7152 BATTERY: CR2032 Parts Illustration d. 2 34 5 1 6 4. Assembly parts: 1. Front housing assembly 2. Outer bezel 3. Keypad assembly 4. Printed Circuit Board (PCB) 5. Back housing assembly 6. Elastomer contact 7. Battery door © 2008 Directed Electronics. All rights reserved. 3 71 2 5. 500-10114 Disassembly instructions 1. Turn the remote control over and remove the battery door. 2. Remove the coin cell battery or batteries. 3. Remove Back Housing. The Back Housing is held in place by tabs along its edge. Insert a small slotted screwdriver into gap between Back Housing and Outer Bezel. c. a. Start in the middle and pry the case up. b. Move the screwdriver along the edge to care fully pry up the tabs at the bottom of the remote. c. Then insert the screwdriver towards the top of the case to pry up the tab. d. Remove Back Housing. Elastomer contact 4. 5. Note: Care must be taken so that the Elastomer contact does not fall out. Remove the PCB, Printed Circuit Board. Remove Keypad assembly. Assembly instructions (not illustrated) 6. Insert Keypad assembly into Front Housing and Outer Bezel. 7. Insert PCB assembly into Front Housing and Outer Bezel 8. Inspect Back Housing Assembly to be sure Elastomer Contact is in place. 9. Assemble the Back Housing to Front Housing and Outer Bezel by snapping tabs in place. 10. Insert coin cell battery or batteries. For 7251V the remote emits beep tones. 11. Install Battery door.

  • 1
© 2008 Directed Electronics. All rights reserved.
Assembly Guide: Viper Responder LE Case
Below are instructions for disassembly and assembly of the Viper Responder LE, and for the
companion 1-way remotes. This guide applies to remote controls with Replacement Part Number
(RPN) 7251V or 7152V.
3
1
2
3
4
5
6
Parts Illustration
Disassembly instructions
Turn the remote control over and remove the bat-
1.
tery door.
Remove the coin cell battery or batteries.
2.
Remove Back Housing. The Back Housing is
3.
held in place by tabs along its edge. Insert
a small slotted screwdriver into gap between
Back Housing and Outer Bezel.
a. Start in the middle and pry the case up.
b. Move the screwdriver along the edge to
care fully pry up the tabs at the bottom of the
remote.
c. Then insert the screwdriver towards the top
of the case to pry up the tab.
d. Remove Back Housing.
Note: Care must be taken so that the Elastomer
contact does not fall out.
Remove the PCB, Printed Circuit Board.
4.
Remove Keypad assembly.
5.
Assembly instructions (not illustrated)
Insert Keypad assembly into Front Housing and
6.
Outer Bezel.
Insert PCB assembly into Front Housing and
7.
Outer Bezel
Inspect Back Housing Assembly to be sure Elas-
8.
tomer Contact is in place.
Assemble the Back Housing to Front Housing
9.
and Outer Bezel by snapping tabs in place.
Insert coin cell battery or batteries. For 7251V
10.
the remote emits
beep tones.
Install Battery door.
11.
Finding the RPN, replacement part number
Turn your remote control over and remove the battery door.
With the door removed read the
silk-screen on the back case to find the RPN, as shown below.
1-800-274-0200
1-800-274-0200
RPN 7251V
RPN 7152
IC:1513A -7251
IC: 1513A-7152
FCC D:EZSDEI7251
FCC ID: EZSDEI7152
BATTERY: CR2016
BATTERY: CR2032
Assembly parts:
1. Front housing assembly
2. Outer bezel
3. Keypad assembly
4. Printed Circuit Board (PCB)
5. Back housing assembly
6. Elastomer contact
7. Battery door
7
3a.
b.
c.
d.
4.
5.
ASSY-LE-CASE-VIPER 2008-11
500-10114
Elastomer contact