Vizio GV52LFHDTV10A User Manual - Page 7

To remove the speakers - tv

Page 7 highlights

VIZIO GV52L FHDTV10A User Manual To remove the speakers If you wish to remove the attached speakers as well and use your Home Theatre System for the audio, please follow the procedure below. 1. Unplug the speaker wires from the GV52L FHDTV10A at the rear of the TV set by carefully pulling down on these two 5-DIN pin connectors, one at a time. 2. To remove the nameplate; make sure that these four screws (T3, 8mm long, self tapping) are removed. These screws are located behind the plate. 3. Remove the four (4) screws that hold the right speaker in place and remove the speaker. The screws are identified by arrows molded into the plastic. After removing speaker, the screws could be left in place for future use if speaker needs to be reinstalled. 4. Repeat step 3 for the left speaker. After removing speaker, the screws could be left in place for future use if speaker needs to be reinstalled. Note: Do not attempt to remove speaker assembly without removing nameplate beforehand; plate will be easily removed after step 2 is done. Version 10/4/2007 7 www.VIZIO.com

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80

VIZIO GV52L FHDTV10A User Manual
Version 10/4/2007
7
www.VIZIO.com
To remove the speakers
If you wish to remove the attached speakers as well and use your Home Theatre System for the audio,
please follow the procedure below.
1.
Unplug the speaker wires from the GV52L
FHDTV10A at the rear of the TV set by
carefully pulling down on these two 5-DIN
pin connectors, one at a time.
2.
To remove the nameplate; make sure that
these four screws (T3, 8mm long, self
tapping) are removed. These screws are
located behind the plate.
3.
Remove the four (4) screws that hold the right
speaker in place and remove the speaker.
The
screws are identified by arrows molded into the
plastic. After removing speaker, the screws
could be left in place for future use if speaker
needs to be reinstalled.
4.
Repeat step 3 for the
left
speaker.
After
removing speaker, the
screws could be left in
place for future use if
speaker needs to be
reinstalled.
Note: Do not attempt to remove speaker assembly without removing nameplate beforehand; plate will
be easily removed after step 2 is done.