Weber Genesis Silver A LP Owner Manual - Page 26

Liquid Propane Cylinder

Get Weber Genesis Silver A LP PDF manuals and user guides View all Weber Genesis Silver A LP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

7) Check for leaks by wetting the fitting with the soap and water solution and watching for bubbles. If bubbles form, or if a bubble grows, there is a leak. You will need: LP cylinder, a soap and water solution and a rag or brush to apply it. 1) Turn the LP cylinder so the opening of the valve is either to the front, side or rear of the Weber Gas Barbecue. Lift and hook the cylinder onto the fuel guage. 2) Loosen the cylinder lock wing nut. Swing the cylinder lock down. Tighten the wing nut. To Connect the hose to the cylinder: 3) Remove the plastic dust cover from the valve. 4) Screw the regulator coupling onto the tank valve, clockwise, or to the right. Hand-tighten only. Note: This is a new type of connection. It tightens clockwise and will not allow gas to flow unless the connection is tight. The connection requires tightening by hand only. ƽ WARNING: Do not use a wrench to tighten the connection. Using a wrench could damage the regulator coupling and could cause a leak. 5) Mix soap and water. 6) Turn on the cylinder valve. If there is a leak, turn off the gas and tighten the fitting. Turn the gas back on and recheck with the soap and water solution. If leak does not stop, Contact the Customer Service Representative in your region using the contact information sheet provided with your manual. Do not use the barbecue. 8) When leak checking is complete, turn gas supply OFF at the source and rinse connections with water. Liquid Propane Cylinder The liquid propane cylinder manufacturer is responsible for the materials, workmanship and performance of the tank. If the tank has a defect malfunctions, or you have a question regarding the tank, call the tank manufacturer's customer service center. The phone number is on the warning decal, which is permanently attached to the tank. If the tank manufacturer has not resolved the issue to your satisfaction, then contact the Customer Service Representative in your region using the contact information sheet provided with your manual. D-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
D-5
Liquid Propane Cylinder
The liquid propane cylinder manufacturer is respon-
sible for the materials, workmanship and performance
of the tank. If the tank has a defect malfunctions, or
you have a question regarding the tank, call the tank
manufacturer’s customer service center. The phone
number is on the warning decal, which is permanently
attached to the tank. If the tank manufacturer has not
resolved the issue to your satisfaction, then contact
the Customer Service Representative in your region
using the contact information sheet provided with your
manual.
You will need: LP cylinder, a soap and water solution
and a rag or brush to apply it.
1)
Turn the LP cylinder so the opening of the valve is
either to the front, side or rear of the Weber Gas
Barbecue. Lift and hook the cylinder onto the fuel
guage.
2)
Loosen the cylinder lock wing nut. Swing the
cylinder lock down. Tighten the wing nut.
To Connect the hose to the cylinder:
3)
Remove the plastic dust cover from the valve.
4)
Screw the regulator coupling onto the tank valve,
clockwise, or to the right. Hand-tighten only.
Note: This is a new type of connection. It tightens
clockwise and will not allow gas to flow unless the
connection is tight. The connection requires tightening
by hand only.
±
WARNING: Do not use a wrench to tighten the
connection. Using a wrench could damage the
regulator coupling and could cause a leak.
5)
Mix
soap and water.
6)
Turn on the cylinder valve.
7)
Check for leaks by wetting the fitting with the soap
and water solution and watching for bubbles. If
bubbles form, or if a bubble grows, there is a leak.
If there is a leak, turn off the gas and tighten the
fitting. Turn the gas back on and recheck with the
soap and water solution.
If leak does not stop, Contact the Customer Service
Representative in your region using the contact
information sheet provided with your manual. Do not
use the barbecue.
8)
When leak checking is complete, turn gas supply
OFF at the source and rinse connections with
water.