Weber Summit Gold B6 LP Owner Manual - Page 36

be leak checked with a soap and water solution before

Get Weber Summit Gold B6 LP PDF manuals and user guides View all Weber Summit Gold B6 LP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

36 MAINTENANCE 13. Remove the Crossover® tube. 14. Pull the selected burner(s) tube(s) from manifold frame and replace with a new burner tube. 15. To reinstall the manifold assembly, reverse steps 7 through 14. ƽCAUTION: The burner openings (1) must be positioned properly over the valve orifices (2). Check proper assembly before fastening manifold in place. ƽWARNING: After reinstalling the gas lines, they should be leak checked with a soap and water solution before using the grill. (See, "Check for gas leaks.") (2) (1) CROSSOVER® IGNITION SYSTEM OPERATIONS If the Crossover® ignition system fails to ignite the LEFT burner in a burner set, light the LEFT burner with a match. If the LEFT burner lights with a match, then check the Crossover® ignition system. • Check that both ignition wires(1,2) are attached properly. (1 ) • Check that the Crossover® ignition button is activating. • You should hear the igniter sparking. If the Crossover® ignition system still fails to light, contact the Customer (2 ) Service Representative in your area using the contact information on our web site. Log onto www.weber.com®. REPLACE IGNITER BATTERIES Parts required: 1 AA alkaline battery per igniter. Unscrew igniter button from bottom of control panel. Remove igniter button and contact spring. Remove old battery and replace with a new AA alkaline battery. Positive end(1) of battery faces up as shown in illustration. Replace spring contact(2) and screw igniter button(3) back down.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
36
13.
Remove the Crossover
®
tube.
14.
Pull the selected burner(s) tube(s) from manifold frame and replace
with a new burner tube.
15.
To reinstall the manifold assembly, reverse steps 7 through 14.
±
CAUTION: The burner openings (1) must be positioned
properly over the valve orifices (2).
Check proper assembly before fastening manifold in place.
±
WARNING: After reinstalling the gas lines, they should
be leak checked with a soap and water solution before
using the grill. (See, “Check for gas leaks.”)
MAINTENANCE
(2)
(1)
(1 )
(2 )
CROSSOVER
®
IGNITION SYSTEM OPERATIONS
If the Crossover
®
ignition system fails to ignite the LEFT burner in a burner
set, light the LEFT burner with a match. If the LEFT burner lights with a
match, then check the Crossover
®
ignition system.
•
Check that both ignition wires(1,2) are attached properly.
•
Check that the Crossover
®
ignition button is activating.
•
You should hear the igniter sparking.
If the Crossover
®
ignition system still fails to light, contact the Customer
Service Representative in your area using the contact information on our
web site. Log onto www.weber.com
®
.
REPLACE IGNITER BATTERIES
Parts required:
1 AA alkaline battery per igniter.
Unscrew igniter button from bottom of control panel. Remove igniter button
and contact spring. Remove old battery and replace with a new AA alkaline
battery. Positive end(1) of battery faces up as shown in illustration. Replace
spring contact(2) and screw igniter button(3) back down.