Weider 9400 Instruction Manual - Page 13

39. Route the Leg Lever Cable (75) under a 115mm Pulley (119). Attach the Pulley and a pair of Large Pulley Covers (113) to the indicated side of the Butterfly Upright (3) with an M10 x 95mm Bolt (92), an M10 Washer (91), and an M10 Nylon Locknut (87). Make sure the tabs on the Pulley Covers are oriented as indicated. 40. Wrap the Leg Lever Cable (75) over a 90mm Pulley (78). Attach the Pulley and a pair of Pulley Covers (68) to the Double "U"-bracket (62) with an M10 x 50mm Bolt (100) and an M10 Nylon Locknut (87). Make sure the small tabs on the Pulley Covers are on the bottom. 41. Remove the preattached 90mm Pulley (not shown) from the "U"-bracket (64). Attach the end of the Leg Lever Cable (75) to the "U"-bracket (64) with an M8 Washer (90) and an M8 Nylon Locknut (34). Note: Do not completely tighten the Locknut; it should be tightened so that only two threads of the Cable show past the Locknut, as shown in the inset drawing. 39 92 Tab 119 113 75 3 87 91 40 100 62 87 68 75 78 68 Small Tab 41 75 64 75 90 34 34 42. Locate the Swivel Low Cable (72), which is the only remaining cable that has an eyelet on one end and a ball on the other end. Route the eyelet end of the Cable through the cage on the Long Base (101) and through the Swivel Upright (5), as shown. Make sure the Cable is over the short bar inside the cage. Attach a 90mm Pulley (78) to the indicated bracket on the Long Base (101) with an M10 x 45mm Bolt (93) and an M10 Nylon Locknut (87). Make sure the Cable is in the groove of the Pulley. 43. Wrap the Swivel Low Cable (72) under a 90mm Pulley (78). Attach the Pulley and a pair of Pulley Covers (68) to the indicated bracket on the Long Base (101) with an M10 x 50mm Bolt (100) and an M10 Nylon Locknut (87). Make sure the large tabs on the Pulley Covers are oriented as indicated. 42 78 72 Cage 87 101 93 5 43 Large Tab 68 101 100 68 78 72 87 16 24. Remove the preattached 90mm Pulleys (78) from the Offset Double "U"-bracket (61). Wrap the Swivel Cable (17) around a 90mm Pulley (78). Attach the Pulley to the Offset Double "U"bracket (61) with an M10 x 50mm Bolt (100) and an M10 Nylon Locknut (87). Make sure the small tabs on the Pulley Covers are on the top. 25. Wrap the Swivel Cable (17) around a 90mm Pulley (78). Attach the Pulley and a Pulley Cover (68) to the next to bottom hole in the Small Pulley Plates (31) with an M10 x 50mm Bolt (100) and an M10 Nylon Locknut (87). Make sure the small tabs on the Pulley Covers are on the bottom. 26. Wrap the Swivel Cable (17) around a 90mm Pulley (78). Attach the Pulley and a pair of Pulley Covers (68) to the bracket on the Swivel Upright (5) with an M10 x 50mm Bolt (100) and an M10 Nylon Locknut (87). Make sure the small tabs on the Pulley Covers are on the top. 27. Attach the end of the Swivel Cable (17) to the bracket on the Swivel Carriage (46) with an M10 x 20mm Bolt (86) and an M10 Nylon Locknut (87). 24 17 Small Tab 78 100 61 87 25 100 31 87 17 78 68 68 Small Tab 26 17 5 100 Small Tab 87 27 68 68 78 46 87 86 17 28. Locate the Lat Cable (88), which is 2263mm long and has a ball on one end and an eyelet on the other. Route the eyelet end of the Cable up through the Butterfly Top Frame (7) and around a 90mm Pulley (78). Attach the Pulley inside of the Butterfly Top Frame with an M10 x 65mm Bolt (18), two M10 Washers (91), two 12mm Spacers (89), and an M10 Nylon Locknut (87). 28 78 87 91 89 7 88 89 91 18 13