Weider Pro 425 English Manual - Page 8

M10 Nylon Locknut; the Backrest 8 must

Get Weider Pro 425 PDF manuals and user guides View all Weider Pro 425 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

6. Screw the Backrest Adjustment Knob (30) into the Frame (1). Pull the Knob out as far as it will go and lower the Backrest Bracket (9) between the Bench Frame. Snap the Knob into an adjustment hole in the Backrest Bracket. Lubricate an M10 x 140mm Bolt (37). Attach the indicated set of holes in the Backrest Frames (10) and the two Plastic Plates (26) to the Bench Frame (1) with the Bolt, two M10 Washers (27), and an M10 Nylon Locknut (35). Note: The warning decals on the Plastic Plates must face away from the bench. Do not overtighten the M10 Nylon Locknut; the Backrest (8) must be able to pivot easily. 7. Press the 40mm x 50mm Inner Cap (45) into the Seat Frame (6). Press six 8mm Bushings (32) into the Seat Frame and the Backrest Frames (10) . Attach the Seat Bracket (14) to the Seat Frame (6) with an M10 x 78mm Bolt (28) and an M10 Nylon Locknut (35). Attach the Seat Bracket (14) to the Frame (1) with an M10 x 100mm Bolt (38) and an M10 Nylon Locknut (35). Lubricate an M10 x 140mm Bolt (37). Attach the bottom set of holes in both the Backrest Frames (10) and the two Plastic Plates (26), and two 12.5mm Spacers (33), to the Seat Frame (6) with the Bolt and an M10 Nylon Locknut (35). Do not overtighten the M10 Nylon Locknut; the Backrest (8) must be able to pivot easily. Tighten the M8 Nylon Locknuts (42) used in step 5. 8. Press two 8mm Bushings (32) into the Leg Lever Bracket (13). Attach the Leg Lever Bracket (13) to the Seat Frame (6) with the Small Adjustment Knob (29). 9. Press three 50mm Square Inner Caps (22) into the Leg Lever (15). Press a 50mm Round Inner Cap (44) into the weight tube. Lubricate an M10 x 78mm Bolt (28). Attach the Leg Lever (15) to the Leg Lever Bracket (13) with the Bolt and an M10 Nylon Locknut (35). Do not overtighten the Nylon Locknut; the Leg Lever must pivot freely. 6 8 30 35 27 10 Hole 9 Adjustment Hole 26 27 1 Decal 26 37 Lubricate 7 33 32 32 6 35 14 38 45 33 35 32 10 28 32 26 1 37 Lubricate 8 32 6 13 29 9 22 35 13 15 28 22 44 Weight 22 Tube 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
8
6.
Screw the Backrest Adjustment Knob (30) into the
Frame (1). Pull the Knob out as far as it will go
and lower the Backrest Bracket (9) between the
Bench Frame. Snap the Knob into an adjustment
hole in the Backrest Bracket.
Lubricate an M10 x 140mm Bolt (37). Attach the
indicated set of holes in the Backrest Frames (10)
and the two Plastic Plates (26) to the Bench
Frame (1) with the Bolt, two M10 Washers (27),
and an M10 Nylon Locknut (35).
Note: The warn-
ing decals on the Plastic Plates must face
away from the bench. Do not overtighten the
M10 Nylon Locknut; the Backrest (8) must be
able to pivot easily.
7.
Press the 40mm x 50mm Inner Cap (45) into the
Seat Frame (6). Press six 8mm Bushings (32) into
the Seat Frame and the Backrest Frames (10) .
Attach the Seat Bracket (14) to the Seat Frame
(6) with an M10 x 78mm Bolt (28) and an M10
Nylon Locknut (35).
Attach the Seat Bracket (14) to the Frame (1) with
an M10 x 100mm Bolt (38) and an M10 Nylon
Locknut (35).
Lubricate an M10 x 140mm Bolt (37). Attach the
bottom set of holes in both the Backrest Frames
(10) and the two Plastic Plates (26), and two
12.5mm Spacers (33), to the Seat Frame (6) with
the Bolt and an M10 Nylon Locknut (35).
Do not
overtighten the M10 Nylon Locknut; the
Backrest (8) must be able to pivot easily.
Tighten the M8 Nylon Locknuts (42) used in
step 5.
8.
Press two 8mm Bushings (32) into the Leg Lever
Bracket (13).
Attach the Leg Lever Bracket (13) to the Seat
Frame (6) with the Small Adjustment Knob (29).
37
10
8
26
30
1
26
9
35
27
27
Lubricate
Hole
Adjustment Hole
Decal
6
37
6
14
35
35
1
26
32
32
32
33
45
13
32
6
29
38
7
8
9.
Press three 50mm Square Inner Caps (22) into
the Leg Lever (15). Press a 50mm Round Inner
Cap (44) into the weight tube.
Lubricate an M10 x 78mm Bolt (28). Attach the
Leg Lever (15) to the Leg Lever Bracket (13) with
the Bolt and an M10 Nylon Locknut (35).
Do not
overtighten the Nylon Locknut; the Leg Lever
must pivot freely.
22
22
15
22
35
13
28
44
Weight
Tube
9
Lubricate
32
33
28
10