Weider Pro Xt15 English Manual - Page 8

Lubricate an M10 x 65mm Bolt 23. Attach the Leg

Get Weider Pro Xt15 PDF manuals and user guides View all Weider Pro Xt15 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

7. Press three 45mm Square Inner Caps (17) into the Leg Lever (18). Press a 25mm Round Inner Cap 7 (33) into the indicated end of the Weight Tube (21). Attach the Weight Tube (21) to the Leg Lever (18) with an M8 x 58mm Bolt (16), two M8 Flat Washers (13), a 10mm Spacer (20), and an M8 Nylon Locknut (9). Press an Angled Outer Cap (31) onto the back end of the Weight Tube. Press a Weight Adapter Bushing (38) into each end of the Weight Adapter (37). 8. Lubricate an M10 x 65mm Bolt (23). Attach the Leg 8 Lever (18) to the Front Leg (19) with the Bolt and an M10 Nylon Locknut (11). Do not overtighten the Nylon Locknut; the Leg Lever must be able to pivot freely. 37 38 17 33 38 16 13 21 17 17 18 20 31 9 13 11 18 23 19 9. Press two 3/4" Round Inner Caps (12) into each of the three Pad Tubes (25). Slide the Pad Tubes through the indicated holes in the Front Leg (19) and the Leg Lever (18). Slide two Foam Pads (10) onto each Pad Tube (25). 9 10 12 19 25 12 10 10. Attach the Curl Pad (26) to the Curl Post (32) with two M6 x 16mm Screws (3). Insert the Curl Post into the Front Leg (19) and secure it with the Curl Post Knob (36). 10 26 18 12 10 25 10 12 32 3 11. Make sure all parts are properly tightened before you use the weight bench. The use of all remaining parts will be explained in Adjusting the Weight Bench starting on page 9. 8 36 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
8
7.
Press three 45mm Square Inner Caps (17) into the
Leg Lever (18). Press a 25mm Round Inner Cap
(33) into the indicated end of the Weight Tube (21).
Attach the Weight Tube (21) to the Leg Lever (18)
with an M8 x 58mm Bolt (16), two M8 Flat Washers
(13), a 10mm Spacer (20), and an M8 Nylon
Locknut (9). Press an Angled Outer Cap (31) onto
the back end of the Weight Tube.
Press a Weight Adapter Bushing (38) into each end
of the Weight Adapter (37).
7
17
17
38
37
38
21
33
17
16
20
13
18
13
9
31
9.
Press two 3/4” Round Inner Caps (12) into each of
the three Pad Tubes (25). Slide the Pad Tubes
through the indicated holes in the Front Leg (19)
and the Leg Lever (18).
Slide two Foam Pads (10) onto each Pad Tube (25).
10. Attach the Curl Pad (26) to the Curl Post (32) with
two M6 x 16mm Screws (3). Insert the Curl Post
into the Front Leg (19) and secure it with the Curl
Post Knob (36).
9
10
25
25
12
19
18
12
12
26
19
32
3
36
12
10
10
10
10
8.
Lubricate an M10 x 65mm Bolt (23). Attach the Leg
Lever (18) to the Front Leg (19) with the Bolt and
an M10 Nylon Locknut (11).
Do not overtighten
the Nylon Locknut; the Leg Lever must be able
to pivot freely.
8
18
11
19
23
11.
Make sure all parts are properly tightened
before you use the weight bench. The use of all
remaining parts will be explained in Adjusting
the Weight Bench starting on page 9.