Weider Victory X25 Power Guide English Manual - Page 19
Backrest, &mci, Extension, Assembly
View all Weider Victory X25 Power Guide manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 19 highlights
PAGE 15 WEIDER SPORTING GOODS STEP 8 BACKREST, SEAT, & &MCI EXTENSION ASSEMBLY Aftti.N*Mt. ' 41 5/16" NYLON LOCK NUT 43 5116" X 21/4" HEX HEAD BOLT 45 5/16" X 2 3/4" CARRIAGE BOLT 49 5/16" X 2" EYE-BOLT 60 1/4" FLAT WASHER 61 114" NYLON LOCK NUT 62 1/4" X 3M" ROUND HEAD MACHINE SCREW 64 114" X 2 112" ROUND HEAD MACHINE SCREW 65 1/4" X 2" CARRIAGE BOLT 76 11/2" SQUARE PLASTIC INSERT CAP 77 3/4" ROUND PLASTIC INSERT CAP 99 5/16" THREADED KNOB QTY " , 2 1 1 1 4 2 4 2 2 2 4 1 Cap the end of the SEAT FRAME (29) with a 1 1/2" SQUARE PLASTIC INSERT CAP (76). a Cap the bottom of the LEG EXTENSION (30) with a 1 1/2" SQUARE PLASTIC INSERT CAP (76). Assemble the ARM PRESS BACKREST (31) to the MAIN UPRIGHT (10) by first assembling 1/4" FLAT WASHERS (60) onto two 1/4" X 2 1/2" ROUND HEAD MACHINE SCREWS (64) and then bolt through the back of the Upright and into the Backrest. Orient the SEAT FRAME (29) so that the end of the tube turns upward. Fit the Bracket of the Seat Frame around the MAIN UPRIGHT (10) Post and set the slot in the Seat Frame over the Pin in the Post. Insert a 5/16" X 2 3/4" CARRIAGE BOLT (45) through the Seat Bracket and Main Upright Post and secure with a 5/16" THREADED KNOB (99). Attach the SEAT MOUNTING BRACKETS (32) (These are flat brackets 2"X 6" with two round holes and a square hole in the center.) to the top side of the SEAT FRAME (29) by bolting down through the Mounting Bracket and then through the Seat Frame with 1/4" X 2" CARRIAGE BOLTS (65). Fasten in place with 1/4" FLAT WASHERS (60) and1/4" NYLON LOCK NUTS (61). DO NOT tighten at this time. Locate the ARM PRESS SEAT (33) over the SEAT MOUNTING BRACKETS (32) so that the wide end of the Seat is to the front of the unit Assemble up through the Brackets and into the bottom of the Seat with 114" X 3/4" ROUND HEAD MACHINE SCREWS (62). Now tighten the Carriage Bolts holding the Brackets. u Bolt the LEG EXTENSION (30) to the hole location at the- end of the SEAT FRAME (29) using a 5/16" X 2 1/4" HEX HEAD BOLT (43) and a 5/16" NYLON LOCK NUT (41). DO NOT OVER TIGHTEN SO THAT THE LEG EXTENSION WILL BE ABLE TO SWING FREELY. 0 31 10 60 64 Press 3/4" ROUND PLASTIC INSERT CAPS (77) into the ends of the 3/4" X 13" PAD BARS (34). Wipe a small amount of liquid dish detergent along the length of the Pad Bars. This will help in the assembly of the Foam Rollers. When the detergent dries, it will also act as an adhesive. Insert the Pad Bars into the 3" X 5 3/4" FOAM ROLLERS (35). Insert one Pad Bar assembly into the access hole at the front of the 34 76 77 SEAT FRAME (29) and slide on a second 3" X 5 3/4" FOAM ROLLER (35). 35 0 0 Insert the other Pad Bar 30 assembly into the bottom section of the LEG EXTENSION (30) and slide on another 3" X 5 3/4" FOAM ROLLER (35). aro 41 Assemble a 5/16" X 2" EYE-BOLT (49) in through the back and bottom of the LEG 35 34 77 EXTENSION (30). Secure with a 5/16" NYLON LOCK NUT (41). 76 33 3 29 41 49 0 35 99 5 2 35 60 64 PIN