Weslo Aero 700 English Manual - Page 5
Maintenance And Trouble-shooting - bike
View all Weslo Aero 700 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 5 highlights
MAINTENANCE AND TROUBLE-SHOOTING Inspect and tighten all parts of the AERO 700 regularly. Replace any worn parts immediately. The AERO 700 can be cleaned with a soft, damp cloth. Keep liquid away from the electronic monitor. Keep the monitor out of direct sunlight or the display may be damaged. Remove the batteries when storing the AERO 700. ELECTRONIC MONITOR TROUBLE-SHOOTING If the electronic monitor does not function properly, the batteries should be replaced. See assembly step 5 on page 5 for instructions. In addition, make sure that the sensor wire is connected to the wire on the monitor. See assembly step 6 on page 5. If the electronic monitor displays incorrect information, the reed switch should be checked. First, remove the pedal and the side shield from one side of the exer- cise bike. Next, refer to the drawing at the right Reed Switch and locate the reed switch. Turn the sprocket until the magnet on the sprocket Magnet Screw is as close as possible to the reed switch. Loosen the screw in the reed switch, move the reed switch slightly closer to the magnet, and tighten the screw. Make sure that the magnet will not hit the reed switch when the sprocket turns. Repeat until the monitor displays correct information. HOW TO TIGHTEN THE PEDALS If the pedals become loose, refer to assembly step 8 on page 5. Tighten the pedal axles into the arms of the crank. Tighten the 1/2" locknuts on the pedal axles. HOW TO ADJUST THE CHAIN The exercise bike features a precision chain that must be kept properly lubricated. Apply a few drops of light multi-purpose oil to the chain every three months. In addition, the chain must be kept properly adjusted. If the chain is too tight, the bearings may be damaged; if the chain is too loose, the fan may be damaged. If the chain causes excessive noise or slips as you pedal, check the chain in the following manner: Fan Axle Nut Adjustment Nuts 1. Remove the fan guards from the front of the exercise bike. Remove the pedal and the side shield from one side of the exercise bike. 2. Press down on the center of the chain. There should be between 1/4Ó and 1Ó of vertical movement in the center of the chain. If the chain is properly adjusted, reattach the pedal, side shield, and fan guards. If the chain needs to be adjusted, see step 3. 3. Loosen both axle nuts. To tighten the chain, turn the adjustment nuts clockwise; to loosen the chain, turn the adjustment nuts counterclockwise. Make sure that the fan is straight and tighten the axle nuts. Reattach the pedal, side shield, and fan guards. 8 5. The Electronic Monitor (19) requires two ÒAAÓ batteries (not included). Alkaline batteries are recommended. Open the battery cover on the back of the Monitor. Insert two batteries into the Monitor. Make sure that the negative ends of the batteries (marked ÒÐÓ) are touching the springs in the Monitor. Close the battery cover. 5 19 Batteries 6. Connect the Sensor Wire (47) into the wire extending from the Electronic Monitor (19). Slide the Electronic Monitor onto the bracket on the Frame (46). Make sure that the Sensor Wire is not pinched between the Monitor and the Frame. 6 46 Cover 19 47 7. This step may have been completed. If not, please apply a small 7 amount of grease to the bolt welded in the Right Handlebar (38). Connect a Link Arm (26) to the lower end of the Right Handlebar (38) with a Brass Handlebar Bushing (27), an M8 Zinc Washer (43), and an 8mm Zinc Locknut (36) as shown. Attach the other Link Arm to the Left Handlebar in the same manner (not shown). 26 38 27 36 43 8. Note: Apply a small amount of grease to all of the small parts 8 assembled in this step. Slide a 13mm Washer (23) onto the 11 24 23 26 32 23 33 39 22 indicated end of a Pedal Axle (24). Insert the Pedal Axle into the right Link Arm (26). Slide a Steel Link Arm Bushing (32), a 13mm Washer (23), and a Pedal Spacer (33) onto the Pedal Axle. Firmly tighten the Pedal Axle clockwise into the right arm of the Crank (39). Tighten a 1/2Ó Locknut (22) onto the Pedal Axle. Attach the other Pedal to the left arm of the Crank (not shown) in the same manner. 9. Make sure that all parts of the exercise bike are properly tightened. 5