Weslo Cadence 340cs Treadmill English Manual - Page 6

POWER IS TURNED ON. Do not disconnect or connect

Get Weslo Cadence 340cs Treadmill PDF manuals and user guides View all Weslo Cadence 340cs Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

3. Hold the Console Base (87) near the right Handrail (4). Make a loop with the indicated plastic tie, and insert the two Wires (53) through the loop. Pull out just enough of the Wires to connect them to the two connectors in the Console Base (87). Plug the red connector into the corresponding connector in the Console Base. The connectors should snap together without being forced. If they do not, rotate the red connector on the Wire and try again. Next, plug the other Wire into the other connector on the Console Base. Important: Make sure that the Wires (53) are fully inserted. Do not force the connectors together. IF THE CONNECTORS ARE NOT INSERTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. Do not disconnect or connect the Wires while the treadmill power cord is plugged in. Refer drawing 3a. Set the Console Base (87) on the Handrails (4, 88). Thread four Console Screws (3) into the Handrails and the Console Base. After all four Screws have been started, tighten the Screws until they are snug; do not overtighten the Screws. Feed the excess Wire Harness (53) into the upper end of the right Handrail (4). Pull the plastic tie tight and cut off the end. 4. Attach the Storage Latch (16) to the left Upright (38) with two Latch Screws (14). Refer to step 2. Tighten the four Handrail Bolts (1). 3 Plastic Tie 4 3a 4 Plastic Tie 4 53 87 87 53 3 88 3 38 16 14 5. Hold a Weight Rack (15) against the right Upright (38) in the position shown. Loosely thread two Rack Screws (14) into the bottom holes in the Weight Rack and the 5 38 Upright. Next, loosely thread four Rack Screws into the other four holes. Then, tighten all six Rack Screws. Set a 3-lb. Weight (not shown) on the bottom hanger on the Weight Rack (15), a 2-lb. Weight on the middle hanger, and a 1-lb. Weight on the top hanger. Attach the other Weight Rack and Weights to the left Upright in the same way (not shown). 15 14 14 Hanger 14 6. Make sure that all parts are tightened before you use the treadmill. To protect the floor or carpet, place a mat under the treadmill. 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
6
3.
Hold the Console Base (87) near the right Handrail (4).
Make a loop with the indicated plastic tie, and insert the
two Wires (53) through the loop. Pull out just enough of
the Wires to connect them to the two connectors in the
Console Base (87). Plug the red connector into the corre-
sponding connector in the Console Base. The connectors
should snap together without being forced. If they do not,
rotate the red connector on the Wire and try again.
Next,
plug the other Wire into the other connector on the
Console Base.
Important: Make sure that the Wires (53)
are fully inserted. Do not force the connectors togeth-
er
.
IF THE CONNECTORS ARE NOT INSERTED PROP-
ERLY, THE CONSOLE MAYBE DAMAGED WHEN THE
POWER IS TURNED ON. Do not disconnect or connect
the Wires while the treadmill power cord is plugged in.
Refer drawing 3a. Set the Console Base (87) on the
Handrails (4, 88). Thread four Console Screws (3) into
the Handrails and the Console Base. After all four
Screws have been started,
tighten the Screws until
they are snug; do not overtighten the Screws.
Feed the excess Wire Harness (53) into the upper end
of the right Handrail (4). Pull the plastic tie tight and cut
off the end.
4. Attach the Storage Latch (16) to the left Upright (38)
with two Latch Screws (14).
Refer to step 2. Tighten the four Handrail Bolts (1).
5. Hold a Weight Rack (15) against the right Upright (38) in
the position shown. Loosely thread two Rack Screws
(14) into the bottom holes in the Weight Rack and the
Upright. Next, loosely thread four Rack Screws into the
other four holes. Then, tighten all six Rack Screws.
Set a 3-lb. Weight (not shown) on the bottom hanger on
the Weight Rack (15), a 2-lb. Weight on the middle
hanger, and a 1-lb. Weight on the top hanger.
Attach the other Weight Rack and Weights to the left
Upright in the same way (not shown).
6.
Make sure that all parts are tightened before you use the treadmill.
To protect the floor or carpet, place a
mat under the treadmill.
14
38
16
38
15
14
14
Hanger
5
88
3
3
4
53
87
3
3a
4
Plastic
Tie
Plastic
Tie
87
53
4
14